Sharp Pgf212xl Manual
Here you can view all the pages of manual Sharp Pgf212xl Manual. The Sharp manuals for Projector are available online for free. You can easily download all the documents as PDF.
Page 61
57 Appendix RS-232C Terminal : mini DIN 9 pin female connector RD SD SG RS CS Signal Name 8 9 6 5 2143 7Pin No. 1. 2. 3. 4. 5. 6. 7. 8. 9.I/O Reference Not connected Connected to internal circuit Connected to internal circuit Not connected Connected to internal circuit Not connected Connected to CS in internal circuit Connected to RS in internal circuit Not connected Receive Data Send Data Signal Ground Request to Send Clear to SendInput Output RS-232C Terminal : D-sub 9 pin male connector of the...
Page 62
58 Info •When controlling the projector using RS-232C commands from a computer, wait for at least 30 seconds after the power has been turned on, and then transmit the commands. •After sending an input selection or picture adjustment command and then receiving an “OK” re- sponse code, the projector may take some time to process the command. If a second command is sent while the projector is still processing the first command, you may receive an “ERR” response code. If this happens, try resending the...
Page 63
59 Appendix Computer DVINormal Stretch Dot By Dot Full Border Area Zoom V-Stretch Normal Stretch Dot By Dot Full Border Area Zoom V-Stretch CONTROL CONTENTSPower ONStandby mode (or 30-second startup time)COMMAND PARAMETERRETURN Power Projector Condition Lamp Name Input Change Volume Keystone AV Mute Freeze Auto Sync Resize On Off Status Status Power Status Quantity Usage Time(Hour) Usage Time(Minute) Life(Percentage) Model Name Check Model Name Check Projector Name Setting 1 (First 4 characters) *1...
Page 64
60 CONTROL CONTENTS Power ONStandby mode (or 30-second startup time)COMMAND PARAMETERRETURN Resize ALL Reset Computer INPUT DVI INPUTOK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or...
Page 65
61 Appendix CONTROL CONTENTSPower ONStandby mode (or 30-second startup time)COMMAND PARAMETERRETURN S-Video INPUT Video INPUT C.M.S. Setting C.M.S. Clock Phase H-position V-position Fine Sync Adjustment Reset OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR OK or ERR...
Page 66
62 CONTROL CONTENTS Power ONStandby mode (or 30-second startup time)COMMAND PARAMETERRETURN Image Shift OSD Display Video System Background Lamp Setting Auto Sync Auto Power Off Auto Restart STANDBY Mode PRJ Mode Language Setup Guide System Sound Internal Speaker RGB Frequency Check Fan Mode Lamp Timer Reset *3-96 – +96 On Off Auto PAL SECAM NTSC4.43 NTSC3.58 PAL-M PAL-N PAL-60 Logo Blue None Bright Eco + Quiet On Off On Off On Off Standard Eco Reverse Invert English Deutsch Español Nederlands...
Page 67
63 Appendix Computer Computer Compatibility Chart •Multiple signal support Horizontal Frequency: 15-110 kHz, Vertical Frequency: 45-85 Hz, The following is a list of modes that conform to VESA. However, this projector supports other signals that are not VESA standards. 27.0 31.5 37.5 27.0 31.5 37.9 27.0 31.5 27.0 31.5 37.9 26.2 31.5 34.7 37.9 37.5 43.3 31.4 35.2 37.9 46.6 48.1 46.9 53.7 40.3 48.4 56.5 60.0 68.7 45.0 47.8 49.7 62.8 47.7 47.8 55.0 66.2 67.5 64.0 80.0 64.0 65.3 75.0 34.9 49.7 60.2 68.7 60...
Page 68
64 Troubleshooting ProblemCheck•Projector power cord is not plugged into the wall outlet.•Power to the external connected devices is off.•The selected input mode is wrong.•Cables are incorrectly connected to the projector.•Remote control battery has run out.•External output has not been set when connecting notebook computer.•The lamp unit cover is not installed correctly. •If the connected DVI digital equipment is turned on before the “DVI-D” input mode is selected on the projector, the image may not be...
Page 69
65 Appendix Problem An unusual sound is occasionally heard from the cabinet. Maintenance indicator on the projector illuminates or blinks in red. The projector cannot be turned on or put into the standby mode using STANDBY/ON on the projector. Picture is green on COMPUTER (Component)/ DVI (Component). Picture is pink (no green) on COMPUTER (RGB)/ DVI (RGB). Picture is too bright and whitish. The cooling fan becomes noisy. The lamp does not light up even after the projector turns on. The lamp suddenly...
Page 70
66 For SHARP Assistance If you encounter any problems during setup or operation of this projector, first refer to the “Troubleshooting” section on pages 64 and 65. If this operation manual does not answer your question, please contact the SHARP Service departments listed below. U.S.A. Sharp Electronics Corporation 1-888-GO-SHARP (1-888-467-4277) [email protected] http://www.sharpusa.com Canada Sharp Electronics of Canada Ltd. (905) 568-7140 http://www.sharp.ca Mexico Sharp Electronics Corporation...