Sharp Mxm264n User Guide

4-51
FACSIMILE
Contents Specifying the original scan size (by numerical values)
When scanning a non-standard size original such as a postcard or card, follow these steps to specify the original size. 
The width can be from 25
 mm to 432 mm (1 to 17), and the height can be from 25 mm to 297 mm (1 to 11-5/8).
1
Touch the [Original] key.
The automatically detected original size appears to the right of the [Original] key.

IMAGE SETTINGS (page 4-46)
2
Touch the [Scan Size] key.
3
Touch the [Size Input] key....

4-52
FACSIMILE
Contents
5
Touch the [OK] key.
The specified size appears in the [Scan Size] key.
 When the scan size is specified by numerical values, the send size cannot be specified.
 When the automatic document feeder is used, an original longer that 432 mm (17) can be scanned (maximum width 
1000 mm (39-3/8)). In this case, touch the [Long Size] key in the screen of step 3.

Specifying the original scan size (by paper size) (page 4-49)

TRANSMITTABLE ORIGINAL SIZES (page 4-29)
AutoX420 Y297Scan...

4-53
FACSIMILE
Contents Specifying the send size of the original
Specify the send size as a paper size. If a send size bigger than the scan size is selected, the image will be enlarged. If 
a send size smaller than the scan size is selected, the image will be reduced.
The send size cannot be specified when [Long Size] is selected for the scan size, or when the scan size is specified by 
numerical values.
1
Touch the [Original] key.

IMAGE SETTINGS (page 4-46)
2
Touch the [Send Size] key.
3
Specify the...

4-54
FACSIMILE
Contents
4
Specify the orientation in which the 
original is placed.
(1) Touch the appropriate [Image Orientation] 
key.
If the wrong orientation is selected here, the image may 
not be sent properly when using enlargement/reduction.
(2) Touch the [OK] key.
The ratio used for reduction or enlargement of the original will appear between the Scan Size and the Send Size.
A3Auto    A4Scan SizeSend Size141%
Fax/OriginalOK
2-Sided
Booklet2-Sided
Tablet
Image Orientation
(2)(1) 

4-55
FACSIMILE
Contents
CHANGING THE EXPOSURE
The exposure can be changed to match the darkness of the original.
Refer the following tables to select appropriate settings.
Exposure settings
ExposureWhen to select
AutoThis setting automatically adjusts the exposure for light and dark parts of the original.
Manual
1-2Select this setting when the original consists of dark text.
3Select this setting for a normal original (neither dark nor light).
4-5Select this setting when the original consists of faint...

4-56
FACSIMILE
Contents
CHANGING THE RESOLUTION
The resolution can be selected to match the characteristics of the original, such as text or photo, the size of the text, and 
the darkness of the image.
Refer the following tables to select appropriate settings.
Resolution settings
ResolutionWhen to select
StandardSelect this setting when your original consists of normal-sized text (like the text in this manual).
FineSelect this setting when your original has small text or diagrams with fine lines.
The...

4-57
FACSIMILE
Contents
CHECKING THE IMAGE TO BE TRANSMITTED 
(Preview)
This function requires the hard disk drive.
If you touch the [Preview] key before scanning the original, you can check the scanned image in the touch panel before 
sending the image.
* The factory default setting is disabled.
Depending on the size of the transmission data, part of the preview image may not appear in the preview screen in the touch 
panel.
1
Place the original.
Place the original face up in the document feeder tray,...

4-58
FACSIMILE
Contents
PREVIEW CHECK SCREEN
This section explains the preview check screen.
(1) Preview image
A preview of the scanned original appears.
If the image is cut off, use the scroll bars at the right and 
bottom of the screen to scroll the image. Touch a bar and 
slide it to scroll. (You can also touch the   keys to 
scroll.)
(2) Change page keys
When there are multiple pages, use these keys to 
change pages.
  keys:  Go to the first or the last page.
  keys:  Go to the previous page or the...

4-59
FACSIMILE
Contents
This section explains the basic procedures for receiving faxes.
RECEIVING FAXES
When the reception mode is set to Auto Reception, the machine will receive and print faxes automatically. The fax 
reception mode is displayed in the base screen.
FAX RECEPTION
 When fax reception is in progress, it is possible to reserve a transmission by performing the transmission in memory 
transmission mode.

TRANSMISSION METHODS (page 4-26)
 To print received faxes, make sure that the required...

4-60
FACSIMILE
Contents
RECEIVING A FAX
When a fax is transmitted to the machine, the machine automatically receives and prints the fax.
1
The machine rings and fax reception 
begins automatically.
A beep sounds when reception ends.
System Settings (Administrator): Speaker Settings
This is used to change the volume and tone of the reception beep.
System Settings (Administrator): Number of Calls in Auto Reception
This is used to change the number of rings on which fax reception begins automatically. To...