Sharp Mx5001n Owners Manual

DIGITAL FULL COLOUR MULTIFUNCTIONAL SYSTEM
Safety GuideSafety GuideSafety Guide
Before installing this product, be sure to read the 
CAUTIONS and INSTALLATION 
REQUIREMENTS sections.
Keep this manual close at hand for reference 
whenever needed.
MX-4100N
MX-4101N
MX-5000N
MX-5001N MODEL:
SPECIFICATIONS
INFORMATION ON DISPOSAL
SUPPLIES INSTALLATION REQUIREMENTS
CAUTIONS
TO THE ADMINISTRATOR OF THE MACHINE
Please see opposite side to access
to Software Setup Guide and Sharpdesk
Installation Guide. 

EMC (this machine and peripheral devices)
Caution!
For complete electrical disconnection, pull out the main plug.
The socket-outlet shall be installed near the equipment and shall be easily accessible.
Shielded interface cables must be used with this equipment to maintain compliance with EMC regulations.
Warning:
This is a Class A product. In a domestic environment this product may cause radio interference in which case the user may be 
required to take adequate measures.
This machine contains the...

1
For the users of the fax function
FAX interface cable and Line cable:
These special accessories must be used with the device.
The Declaration of Conformity can be viewed at the following URL address.
http://www.sharp.de/doc/MX-FXX2.pdf 

2
Contents
The products that meet the ENERGY STAR®  guidelines carry the logo shown above.
The products without the logo may not meet the ENERGY STAR®  guidelines.
Warranty
While every effort has been made to make this document as accurate and helpful as possible, SHARP Corporation makes no 
warranty of any kind with regard to its content. All information included herein is subject to change without notice. SHARP is not 
responsible for any loss or damages, direct or indirect, arising from or related to...

3
CAUTIONS
1. Do not touch the transfer belt. Scratches or smudges on the transfer belt will 
cause dirty prints.
2. The fusing unit is extremely hot.  Exercise care in this area. 
3. Do not look directly at the light source. Doing so may damage your eyes.
4. When the machine is installed, the adjusters (4) must be lowered to the floor 
to secure the machine (prevent it from moving).
Rotate the adjusters in the locking direction until they are in firm contact with 
the floor.
If you find it necessary to...

4
CAUTIONS
Laser information
Wave length 790 nm ±10 nm
Pulse times
(North America and Europe)MX-4100N/MX-4101N:
3.5 µs ±3.5 ns /7 mm Heavy Paper 3.2 µs ±3.2 ns /7 mm
MX-5000N/MX-5001N:
2.8 µs ±2.8 ns /7 mm Heavy Paper 3.2 µs ±3.2 ns /7 mm
Output power Max 0.6 mW (LD1+LD2)
Caution
Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure.
This Digital Equipment is CLASS 1 LASER PRODUCT (IEC 60825-1 Edition 1.2-2001)
For North...

5
INSTALLATION REQUIREMENTS
Improper installation may damage this product. Please note the following during initial installation and whenever the 
machine is moved.
1. The machine should be installed near an accessible 
power outlet for easy connection.
2. Be sure to connect the power cord only to a power 
outlet that meets the specified voltage and current 
requirements. Also make certain the outlet is properly 
grounded.
• For the power supply requirements, see the name 
plate in the lower left corner...

6
SUPPLIES
Standard supplies for this product that can replaced by the user include paper, toner cartridges, and staple cartridges for 
the finisher.
Be sure to use only SHARP-specified products for the toner cartridges, finisher staple cartridge, saddle stitch finisher 
staple cartridge, and transparency film.
Storage of supplies
Proper storage
1. Store the supplies in a location that is:
• clean and dry,
• at a stable temperature,
• not exposed to direct sunlight.
2. Store paper in the wrapper and...

7
SPECIFICATIONS
Machine specifications / copier specifications
* First copy out time is measured with original on the document glass in full ready condition with fuser at operating temperature and 
mirror motor at operating speed in each of black and white mode and colour mode, actual time may vary based on environment 
conditions.
NameDigital Full Colour Multifunctional System MX-4100N/MX-4101N/MX-5000N/MX-5001N
TypeDesktop
Photoconductive typeOPC drum
Printing methodElectrophotographic system (laser)...

8
SPECIFICATIONS
Machine specifications / copier specifications (Continued)
*1 Output tray (Center tray) cannot be used when the finisher or saddle stitch finisher is installed.
*2 Type A connectors are located on the front of the machine and on the right side of the machine at the back (total of two 
connectors); however, the connectors cannot be used simultaneously. Only one of the connectors can be used.
Bypass tray
Paper sizes: A3W, A3, B4, A4, A4R, B5, B5R, A5R, envelopes, 12 x 18, 11 x 17, 8-1/2 x...