Sharp MX M453N User Manual
Have a look at the manual Sharp MX M453N User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 615 Sharp manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
![Page 226
2-114
COPIER
Contents
The image can be reduced when using the centring function, but not enlarged.
When the original size or the paper size is displayed as a special size, this function cannot be used.
To cancel centring...
Touch the [Centring] key in the screen of step 3 so that it is not highlighted.
Downloaded From ManualsPrinter.com Manuals](http://img.usermanuals.tech/thumb/68/37907/w64_Sharp_MX-M453N-225.png "Page 226
2-114
COPIER
Contents
The image can be reduced when using the centring function, but not enlarged.
When the original size or the paper size is displayed as a special size, this function cannot be used.
To cancel centring...
Touch the [Centring] key in the screen of step 3 so that it is not highlighted.
Downloaded From ManualsPrinter.com Manuals")
![Page 227
2-115
COPIER
Contents
ADJUSTING THE SHARPNESS OF AN
IMAGE (Sharpness)
This is used to sharpen an image or make it softer.
1
Place the original.
Place the original face up in the document feeder tray, or face down on the document glass.
2
Select the special modes.
(1) Touch the [Special Modes] key.
(2) Touch the keys to switch through the screens.
(3) Touch the [Sharpness] key.
3
Adjust the image.
(1) Touch the [Soft] key or the [Sharp] key so
that it is highlighted.
(2) Touch the [OK] key.
You will...](http://img.usermanuals.tech/thumb/68/37907/w64_Sharp_MX-M453N-226.png "Page 227
2-115
COPIER
Contents
ADJUSTING THE SHARPNESS OF AN
IMAGE (Sharpness)
This is used to sharpen an image or make it softer.
1
Place the original.
Place the original face up in the document feeder tray, or face down on the document glass.
2
Select the special modes.
(1) Touch the [Special Modes] key.
(2) Touch the keys to switch through the screens.
(3) Touch the [Sharpness] key.
3
Adjust the image.
(1) Touch the [Soft] key or the [Sharp] key so
that it is highlighted.
(2) Touch the [OK] key.
You will...")
![Page 229
2-117
COPIER
Contents
4
Set the number of copies (number of
sets) with the numeric keys.
If you will copy multiple originals using the document glass,
switch to sort mode after this step.
☞Sort mode (page 2-33)
Up to 999 copies (sets) can be set.
If an incorrect number of copies is set...
Press the [CLEAR] key ( ) and then enter the correct number.
5
Press the [START] key.
One set of copies is printed.
If you are using the document glass to copy multiple originals, change originals and press the...](http://img.usermanuals.tech/thumb/68/37907/w64_Sharp_MX-M453N-228.png "Page 229
2-117
COPIER
Contents
4
Set the number of copies (number of
sets) with the numeric keys.
If you will copy multiple originals using the document glass,
switch to sort mode after this step.
☞Sort mode (page 2-33)
Up to 999 copies (sets) can be set.
If an incorrect number of copies is set...
Press the [CLEAR] key ( ) and then enter the correct number.
5
Press the [START] key.
One set of copies is printed.
If you are using the document glass to copy multiple originals, change originals and press the...")
![Page 230
2-118
COPIER
Contents
7
Change the settings.
(1) Touch the key of the setting that you want
to change.
The setting screen of the touched key opens. Change the
settings and touch the [OK] key.
(2) Touch the [OK] key.
To change the number of sets printed, set the desired number of copies (sets) with the numeric keys. After changing
the number of sets, touch the [End] key in the touch panel (not the [START] key) to print the sets.
Special modes that can be adjusted are Margin Shift, Pamphlet Copy,...](http://img.usermanuals.tech/thumb/68/37907/w64_Sharp_MX-M453N-229.png "Page 230
2-118
COPIER
Contents
7
Change the settings.
(1) Touch the key of the setting that you want
to change.
The setting screen of the touched key opens. Change the
settings and touch the [OK] key.
(2) Touch the [OK] key.
To change the number of sets printed, set the desired number of copies (sets) with the numeric keys. After changing
the number of sets, touch the [End] key in the touch panel (not the [START] key) to print the sets.
Special modes that can be adjusted are Margin Shift, Pamphlet Copy,...")
![Page 232
2-120
COPIER
Contents
4
After scanning is finished, check the
number of sheets that were scanned and
touch the [OK] key.
Copying will begin.
When job build mode is used, the number of scanned sheets
appears when the [Read-End] key is touched.
The number that is displayed is the number of scanned
original sheets, not the number of scanned original pages.
For example, when two-sided copying is performed using
one original, the number 1 will appear to indicate that one
original sheet was scanned,...](http://img.usermanuals.tech/thumb/68/37907/w64_Sharp_MX-M453N-231.png "Page 232
2-120
COPIER
Contents
4
After scanning is finished, check the
number of sheets that were scanned and
touch the [OK] key.
Copying will begin.
When job build mode is used, the number of scanned sheets
appears when the [Read-End] key is touched.
The number that is displayed is the number of scanned
original sheets, not the number of scanned original pages.
For example, when two-sided copying is performed using
one original, the number 1 will appear to indicate that one
original sheet was scanned,...")
![Page 234
2-122
COPIER
Contents
1
Insert the originals face up in the
document feeder tray.
●When Same Width is used
Place the originals with the sides that are the same length
aligned on the left.
●When Different Width is used
Place the originals with the corners aligned in the far left corner
of the document feeder tray.
2
Select the special modes.
(1) Touch the [Special Modes] key.
(2) Touch the keys to switch through the screens.
(3) Touch the [Mixed Size Original] key.
☞Special modes menu (2nd screen)...](http://img.usermanuals.tech/thumb/68/37907/w64_Sharp_MX-M453N-233.png "Page 234
2-122
COPIER
Contents
1
Insert the originals face up in the
document feeder tray.
●When Same Width is used
Place the originals with the sides that are the same length
aligned on the left.
●When Different Width is used
Place the originals with the corners aligned in the far left corner
of the document feeder tray.
2
Select the special modes.
(1) Touch the [Special Modes] key.
(2) Touch the keys to switch through the screens.
(3) Touch the [Mixed Size Original] key.
☞Special modes menu (2nd screen)...")
![Page 235
2-123
COPIER
Contents
4
Press the [START] key.
Copying will begin.
To cancel scanning and copying...
Press the [STOP] key ( ).
When [Different Width] is selected on the MX-M283N, the 2-Sided to 2-Sided and 2-Sided to 1-Sided settings of
automatic 2-Sided copying cannot be used.
When [Different Width] is selected, the staple function cannot be used.
The mixed size original function cannot be used to copy originals that are the same size but are placed in different
orientations (A4 and A4R (8-1/2 x 11...](http://img.usermanuals.tech/thumb/68/37907/w64_Sharp_MX-M453N-234.png "Page 235
2-123
COPIER
Contents
4
Press the [START] key.
Copying will begin.
To cancel scanning and copying...
Press the [STOP] key ( ).
When [Different Width] is selected on the MX-M283N, the 2-Sided to 2-Sided and 2-Sided to 1-Sided settings of
automatic 2-Sided copying cannot be used.
When [Different Width] is selected, the staple function cannot be used.
The mixed size original function cannot be used to copy originals that are the same size but are placed in different
orientations (A4 and A4R (8-1/2 x 11...")
2-119 COPIER Contents CHECKING THE NUMBER OF SCANNED ORIGINAL SHEETS BEFORE COPYING (Original Count) The number of scanned original sheets can be counted and displayed before copying is executed. By allowing you to check the number of original sheets that were scanned, this helps reduce the occurrence of copy mistakes. 1 Insert the originals face up in the document feeder tray. Insert the originals all the way into the document feeder tray. Multiple originals can be placed in the document feeder tray. The stack of originals must not be higher than the indicator line on the tray. 2 Select Original Count. (1) Touch the [Special Modes] key. ☞SPECIAL MODES (page 2-41) (2) Touch the keys to switch through the screens. (3) Touch the [Original Count] key so that it is highlighted. (4) Touch the [OK] key. You will return to the base screen of copy mode. 3 Press the [START] key. To cancel scanning and copying... Press the [STOP] key ( ). 1 1 Indicator line Special Modes 22 OK Image Edit Quick FileProof Copy Sharpness Slow Scan ModeOriginal CountMixed Size Original Stamp File (4)(2)(3) Downloaded From ManualsPrinter.com Manuals
2-120 COPIER Contents 4 After scanning is finished, check the number of sheets that were scanned and touch the [OK] key. Copying will begin. When job build mode is used, the number of scanned sheets appears when the [Read-End] key is touched. The number that is displayed is the number of scanned original sheets, not the number of scanned original pages. For example, when two-sided copying is performed using one original, the number 1 will appear to indicate that one original sheet was scanned, not 2 to indicate the front-side page and the reverse side page. If the displayed number of original sheets is different from the actual number of original sheets... Press the [STOP] key ( ). To cancel the original count mode setting... Touch the [Original Count] key in the screen of step 2 so that it is not highlighted. OKCancel 130 pages of original have been scanned. Copy the scanned data? Downloaded From ManualsPrinter.com Manuals
2-121
COPIER
Contents
COPYING ORIGINALS OF DIFFERENT SIZES
(Mixed Size Original)
Even when B4 (8-1/2 x 14) originals are mixed in with A3 (11 x 17) originals, all originals can be copied at once. When
scanning the originals, the machine automatically detects the size of each original and uses paper appropriate for that size.
When mixed size original is combined with auto ratio selection, the ratio is adjusted individually for each original according
to the selected paper size, enabling output on a uniform paper size.
When mixed size original is combined with auto ratio selection
(Auto ratio selection and A3 (11 x 17) are selected)
There are two settings for mixed size originals.
Same Width
Use this setting for originals that are different sizes but have sides that are the same length. The originals
are inserted in the document feeder tray with the sides that are the same length aligned together on the left.
x 17 and 8-1/2 x 11 x 14 and 8-1/2 x 11R x 14 and 5-1/2 x 8-1/2
x 13 and 8-1/2 x 11R x 13 and 5-1/2 x 8-1/2 x 11R and 5-1/2 x 8-1/2
Different Width
Use this setting when the originals are different sizes and do not have sides that are the same length. This
setting can only be used for the following combinations of sizes:
x 17 and 8-1/2 x 14 x 17 and 8-1/2 x 13 x 17 and 5-1/2 x 8-1/2
OriginalsCopies
A3 B4
A3 B4
OriginalsCopies
A B4 (8-1/2 x 14) size original will be
enlarged to A3 (11 x 17) size.
A3 B4
A3 A3
Downloaded From ManualsPrinter.com Manuals
2-122 COPIER Contents 1 Insert the originals face up in the document feeder tray. ●When Same Width is used Place the originals with the sides that are the same length aligned on the left. ●When Different Width is used Place the originals with the corners aligned in the far left corner of the document feeder tray. 2 Select the special modes. (1) Touch the [Special Modes] key. (2) Touch the keys to switch through the screens. (3) Touch the [Mixed Size Original] key. ☞Special modes menu (2nd screen) (page 2-42) 3 Select Mixed Size Original settings. (1) Touch the [Same Width] key or the [Different Width] key as appropriate for the originals. (2) Touch the [OK] key. You will return to the base screen of copy mode. A3 (11 x 17) A4 (8-1/2 x 11) Place with the sides that are the same length aligned on the left. B4 (8-1/2 x 14) A3 (11 x 17) B4 (8-1/2 x 14) Place the originals aligned to the far left corner. OKCancel Same Width Different Width OKSpecial Modes Mixed Size Original Place the same width originals. (1)(2) Downloaded From ManualsPrinter.com Manuals
2-123 COPIER Contents 4 Press the [START] key. Copying will begin. To cancel scanning and copying... Press the [STOP] key ( ). When [Different Width] is selected on the MX-M283N, the 2-Sided to 2-Sided and 2-Sided to 1-Sided settings of automatic 2-Sided copying cannot be used. When [Different Width] is selected, the staple function cannot be used. The mixed size original function cannot be used to copy originals that are the same size but are placed in different orientations (A4 and A4R (8-1/2 x 11 and 8-1/2 x 11R), etc.). To cancel the mixed size original setting... Touch the [Cancel] key in the screen of step 3. System Settings (Administrator): Original Feeding Mode The original feeding mode can be set to always scan mixed size originals. Downloaded From ManualsPrinter.com Manuals
2-124 COPIER Contents COPYING THIN ORIGINALS (Slow Scan Mode) Use this function when you wish to scan thin originals using the automatic document feeder. This function helps prevent thin originals from misfeeding. 1 Insert the originals face up in the document feeder tray. Insert the originals all the way into the document feeder tray. Multiple originals can be placed in the document feeder tray. The stack of originals must not be higher than the indicator line on the tray. If the originals are inserted with too much force, they may crumple and misfeed. 2 Select Slow Scan Mode. (1) Touch the [Special Modes] key. ☞SPECIAL MODES (page 2-41) (2) Touch the keys to switch through the screens. (3) Touch the [Slow Scan Mode] key so that it is highlighted. (4) Touch the [OK] key. You will return to the base screen of copy mode. 3 Press the [START] key. Copying will begin. To cancel scanning and copying... Press the [STOP] key ( ). D C B A D C BA 1 1 Indicator line Special Modes 22 OK Image Edit Quick FileProof Copy Sharpness Slow Scan ModeOriginal CountMixed Size Original Stamp File (4)(2)(3) Downloaded From ManualsPrinter.com Manuals
2-125 COPIER Contents The 2-Sided to 2-Sided and 2-Sided to 1-Sided modes of automatic 2-sided copying cannot be used. To cancel the slow scan mode setting... Touch the [Slow Scan Mode] key in the screen of step 2 so that it is not highlighted. System Settings (Administrator): Original Feeding Mode This is used to have scanning always take place in slow scan mode. Downloaded From ManualsPrinter.com Manuals
2-126 COPIER Contents This section explains convenient copy functions such as interrupting a copy run, changing the order of reserved copy jobs, and storing copy settings in a program. INTERRUPTING A COPY RUN (Interrupt copy) When you need to make an urgent copy and the machine is busy with a long copy run or other job, use interrupt copy. Interrupt copy temporarily stops the job in progress and lets you perform the interrupt copy job first. CONVENIENT COPY FUNCTIONS 1 Touch the [Interrupt] key. The [Interrupt] key does not appear while an original is being scanned. 2 Place the original. Place the original face up in the document feeder tray, or face down on the document glass. 3 Select copy settings and press the [START] key. The interrupt copy job begins. 4 When the interrupt copy job is completed, the interrupted job resumes. To cancel scanning and copying... Press the [STOP] key ( ). Special Modes Plain2-Sided Copy Output File Quick File Copy Ratio 100% A33.2.1.A4R OriginalPaper SelectAuto A4 PlainAuto ExposureAutoB44. A4A4 Copies in progress from tray 4. Ready to scan for next copy job.Interrupt7 Preview 1 1 Downloaded From ManualsPrinter.com Manuals
2-127 COPIER Contents If user authentication is enabled, the login screen will appear when the [Interrupt] key is pressed. Enter your user name and password to log in. The number of copies made will be added to the count of the user that logged in. Depending on the settings of the job in progress, the [Interrupt] key may not appear. Interrupt copy cannot be used in combination with the following special modes: Job Build, Tandem Copy, Book Copy, Card Shot, Multi-Page Enlargement, Original Count If the document glass is used for an interrupt copy job, 2-sided copying, sort copying, and staple sort copying cannot be selected. If any of these functions are necessary, use the automatic document feeder. Downloaded From ManualsPrinter.com Manuals
2-128 COPIER Contents CHECKING A PREVIEW IMAGE OF A COPY (Preview) You can touch the [Preview] key so that it is highlighted in the base screen and then scan the original to check a preview image of the copy in the touch panel before printing the copy. 1 Place the original. Place the original face up in the document feeder tray, or face down on the document glass. 2 Touch the [Preview] key so that it is highlighted. 3 Select copy settings and press the [START] key. After the original is scanned, a preview image of the copy appears in the touch panel. The copy is not printed until the [Start Copy] key is touched in the preview screen. 4 Check the preview image and then touch the [Start Copy] key. Copy printing begins. For details on the preview screen, see PREVIEW SCREEN (page 2-130). If you need to change the copy settings, touch the [Reset] key. To cancel copying... Press the [STOP] key ( ). Special Modes Plain2-Sided Copy Output File Quick File Copy Ratio 100% A33.2.1.A4A4R OriginalPaper SelectAuto A4 PlainAuto ExposureAutoB44. A4 A4Preview PreviewReset Display Rotation Start Copy Function Rev. Display Output /00100001 Downloaded From ManualsPrinter.com Manuals