Sharp MX M453N User Manual

							2-29
COPIER
Contents
2
Store the original size.
(1) Touch the [Store/Delete] tab.
(2) Touch a key for storing a custom original 
size.
Touch a key that does not show a size ( ).
If you wish to edit or clear a previously stored key...
Touch the key that you want to edit or clear. The following screen will appear.
 To edit the key, touch the [Amend] key and go to the next step.
 To clear the key, touch the [Delete] key. Make sure that the original size has been cleared and touch the [OK] key.
3
Enter the original size.
(1) Enter the X (horizontal) dimension of the 
original.
Touch the X (width) numeric value display key to open a 
number entry screen. Enter the width of the original with 
the numeric keys, and touch the [OK] key in the number 
entry screen. A dimension from 25 mm to 432 mm (1 to 
17) can be entered.
(2) Enter the Y (vertical) dimension of the 
original.
Touch the Y (height) numeric value display key to open a 
number entry screen. Enter the height of the original with 
the numeric keys, and touch the [OK] key in the number 
entry screen. A dimension from 25 mm to 297 mm (1 to 
11-5/8) can be entered.
(3) Touch the [OK] key.
You can also touch the   keys to change the number.
The stored original size will be retained even if the main power is turned off.
To cancel the operation...
Press the [CLEAR ALL] key ( ).
OriginalOK
OK
X254 Y210
RecallStore/Delete
Custom Size
(1)(2)
AmendDeleteCancel
A custom size has already been stored
in this location.
OK
OK
Size InputCancel
Original
(25~432)
mm
(25~297)
mm
420X
Y297
(3)(1)
(2)
Downloaded From ManualsPrinter.com Manuals 
						

							2-30
COPIER
Contents Retrieving a stored original size
To retrieve a stored original size, touch the [Original] key in the base screen of copy mode and perform the steps below.
1
Touch the [Custom Size] key.
2
Retrieve the desired stored original size.
(1) Touch the [Recall] tab.
(2) Touch the key of the original size that you 
wish to retrieve.
(3) Touch the [OK] key.
To cancel the operation...
Press the [CLEAR ALL] key ( ).
A5
A5R
B5
216x340
A4R
216x343
A4A3
B5RB4
Custom Size
OriginalOK
Size Input
Inch
AB
A4Auto
Manual
X254 Y210
Custom Size
OriginalOK
OK
RecallStore/Delete
(3)(2)(1)
Downloaded From ManualsPrinter.com Manuals 
						

							2-31
COPIER
Contents
OUTPUT
To select output functions and the output tray, touch the [Output] key in the base screen of copy mode. Output functions 
that can be selected are sort, group, offset, staple sort, saddle stitch, and punch. All explanations of the settings below 
assume that a saddle stitch finisher is installed.
(1) [Offset Tray] key ([Centre Tray] key*)
Output is delivered to the offset tray. The [Offset Tray] 
key is automatically selected when the [Staple Sort] key 
is selected.
* When a finisher or saddle stitch finisher is not installed, 
this key is the [Centre Tray] key.
(2) [Offset] key
This is used to offset each set of output from the previous 
set.
The offset function operates when the checkbox is 
selected   and does not operate when the checkbox is 
not selected  . (The offset checkmark is automatically 
cleared when the staple sort function is selected.)
☞Offset function (page 2-33)
(3) [Sort] key
This is used to sort (collate) output into sets.
☞Sort mode (page 2-33)
(4) [Staple Sort] key
This is used to sort output into sets, staple each set, and 
deliver the sets to the tray. (Note that the sets will not be 
offset in the output tray.) When this function is selected, 
three keys will appear for selecting the staple position.
☞Staple sort function / Saddle stitch function (page 
2-34)
(5) [Group] key
This is used to group copies by page.
☞Group mode (page 2-33)
(6) Output display
An icon will appear to indicate the output mode.(7) [Right Tray] key
Select this key to have output delivered to the right tray.
When the right tray is selected, offset, staple sort, saddle 
stitch, punch, and fold cannot be selected.
(8) [OK] key
Touch this key to close the output screen and return to 
the base screen.
(9) [Saddle Stitch] key
This is used to staple and fold each set of copies at the 
centreline.
☞Staple sort function / Saddle stitch function (page 
2-34)
When this key is touched, the saddle stitch setting screen 
appears. (Only when Automatic Saddle Stitch is 
enabled in the system settings (administrator).)
(10) [Punch] key
This is used to punch holes in the output.
☞Punch function (page 2-37)
(11) [Fold] key
This folds printed output in half. You can choose whether 
the output is folded inward or outward.
☞Paper folding function (page 2-36)
OKOutput
Sort
Right Tray
Offset
Offset
Tray
Staple
Sort
Group
Saddle
StitchPunch
Fold
(6)(7)(8)
(3)
(4)
(5)
(1)
(2)
(11)
(9)
(10)
Downloaded From ManualsPrinter.com Manuals 
						

							2-32
COPIER
Contents
The above screen shows the keys that appear when a saddle stitch finisher is installed. The keys that appear will vary 
depending on what peripheral devices are installed.
In addition, it may not be possible to select some keys depending what peripheral devices are installed. If your screen is 
different from the screen of previous page, see the screens that follow.
Example
The screen when a finisher or saddle stitch finisher is not installed.
Right TrayOffset
Tray
Sort
Group
Offset
OutputOK
Downloaded From ManualsPrinter.com Manuals 
						

							2-33
COPIER
Contents
OUTPUT MODES
This section explains the output modes.
Sort mode
This is used to sort (collate) output into sets.
Example: Sorting the output into 5 sets
Group mode
This function groups copies by page.
Example: Groups of 5 copies of each page
Offset function
This function offsets each set of copies from the previous set in the output tray, making it easy to separate sets of copies.
The sort function is automatically selected when 
originals are placed in the automatic document feeder.
 When the Quick File Folder for document filing is 
full, copying of a large number of originals using the 
sort function will be impeded. Delete unneeded files 
from the Quick File Folder.
Sort
Output
Originals Output
Set the number of copies (5).
Touch the [Output] key.
Touch the [Sort] key.
Press the [START] key.
The group function is automatically selected when an 
original is placed on the document glass.
Group
Output
Originals Output
Set the number of copies (5).
Touch the [Output] key.
Touch the [Group] key.
Press the [START] key.
 The offset function cannot be used in the right tray.
 The offset function cannot be selected when the staple sort function is selected.
Offset function ON Offset function OFF
Downloaded From ManualsPrinter.com Manuals 
						

							2-34
COPIER
Contents Staple sort function / Saddle stitch function
The staple sort function sorts output into sets, staples each set, and delivers the sets to the tray.
The saddle stitch function staples each set in 2 places at the centreline and folds the stapled set.
The relations between the stapling positions, paper orientation, permitted paper sizes for stapling, and number of sheets 
that can be stapled are shown below.
For original placement orientations, see Original placement orientation (for the staple sort and punch functions) (page 
2-37).
*1 When the top left corner or the bottom left corner of the paper is stapled in one place by the finisher (large stacker), the staple is 
placed diagonally. (Diagonal stapling)
*2 Two sheets (one sheet when pamphlet stapling is performed) of paper up to 256 g/m
2 (68 lbs.) can be stapled as covers. When this 
is done, the number of sheets that can be used is two less (one less for saddle stitch) than the stated maximum.
Stapling positionsVertically-oriented paperHorizontally-oriented paper
1 staple at top left 
corner*1
Applicable paper sizes
A4, B5, 8-1/2 x 11, 16K
Number of sheets that can 
be stapled:
Max. 50 sheets*
2
Saddle stitch finisher
Applicable paper sizes
A3, B4, A4R, B5R, 11 x 17, 
8-1/2 x 14, 8-1/2 x 13-1/2, 
8-1/2 x 13-2/5, 8-1/2 x 13, 
8-1/2 x 11R, 8K, 16KR
Number of sheets that can be stapled
A3, B4, 11 x 17, 8-1/2 x 14, 
8-1/2 x 13-1/2, 8-1/2 x 13-2/5,  
8-1/2 x 13, 8K:
Max. 25 sheets*
2
A4R, B5R, 8-1/2 x 11R, 16KR:
Max. 50 sheets*2
Finisher
Applicable paper sizes
A3, B4, A4R, 11 x 17, 8-1/2 x 14, 
8-1/2 x 13-1/2, 8-1/2 x 13-2/5,  
8-1/2 x 13, 8-1/2 x 11R, 8K, 16KR
Number of sheets that can be stapled
A3, B4, 11 x 17, 8-1/2 x 14, 
8-1/2 x 13-1/2, 8-1/2 x 13-2/5,  
8-1/2 x 13, 8K:
Max. 30 sheets*
2
A4R, 8-1/2 x 11R, 16KR:
Max. 50 sheets*2
Finisher (large stacker)
Applicable paper sizes
A3, B4, A4R, 11 x 17, 8-1/2 x 14, 
8-1/2 x 13-1/2, 8-1/2 x 13-2/5,  
8-1/2 x 13, 8-1/2 x 11R, 8K
Number of sheets that can be stapled
Max. 30 sheets*
2
1 staple at bottom left 
corner*1
2 staples at left edge
Saddle stitch (only with 
saddle stitch finisher)Saddle stitch cannot be used 
when the paper is oriented 
verticallyApplicable paper sizes
A3, B4, A4R, 11 x 17, 8-1/2 x 14, 
8-1/2 x 11R, 8K, 16KR
Number of sheets that can be stapled: 
Max. 15 sheets*
2
45
Saddle stitch Staple sort
Downloaded From ManualsPrinter.com Manuals 
						

							2-35
COPIER
Contents
 The number of sheets that can be stapled at once includes any covers and/or inserts that are inserted.
 When Mixed Size Original in the special modes is used with the Same Width setting, the maximum number of sheets that 
can be stapled is 25 for a saddle stitch finisher or 30 for a finisher regardless of the paper size.
 The saddle stitch function can only be used when a saddle stitch finisher is installed.
Downloaded From ManualsPrinter.com Manuals 
						

							2-36
COPIER
Contents Paper folding function
When a saddle stitch finisher is installed, the fold function can be used to fold printed output in half.
Paper sizes that can be folded using the paper folding function are A4R, B4, A3, 8-1/2 x 11R, 8-1/2 x 14, 11 x 17, 
16KR, and 8K. For detailed information on the sizes and types of paper that can be folded, see the specifications in the 
Safety Guide.
Touch the [Fold] key to open the fold settings screen. To fold inward (printed side inside), touch the [Fold Inside] key. To 
fold outward (printed side outside), touch the [Fold Outside] key.
 Special media such as transparency film and tab paper cannot be used.
 When the paper folding function is selected, the staple or hole punch function cannot be used.
 When two-sided printing is disabled in the machines system settings (administrator), the paper folding function cannot be 
used.
Fold insideFold outside
Output
Fold
Select fold direction for 1-sided copy.
Select fold direction of Side 1 for 2-sided copy.
Fold copies inside.
OK
OKCancel
Fold Inside
Fold Outside
Downloaded From ManualsPrinter.com Manuals 
						

							2-37
COPIER
Contents Punch function
If an optional punch module is installed, holes can be punched in output.
Paper size that can be punched is B5R to A3 (7-1/4 x 10-1/2 to 11 x 17). However, A3W (12 x 18) sized paper and 
special media such as transparency film and tab paper cannot be used.
Original placement orientation (for the staple sort and punch functions)
When using the staple sort function or the punch function, the original must be placed as shown below to enable stapling 
or punching in the desired position on the paper.
The hole punch function cannot be used with the saddle stitch or paper folding function together.
Staple sortPunch
Document feeder trayDocument glassDocument feeder trayDocument glass
One staple (top)
Two staples
One staple (bottom)
[Original 1] [Punch positions] [Examples]
[Original 2] [Punch positions]
abcabc
abcabc
abcabc
abcabc
abcabc
Downloaded From ManualsPrinter.com Manuals 
						

							2-38
COPIER
Contents
MAKING COPIES USING THE BYPASS TRAY
In addition to plain paper, the bypass tray allows you to make copies on transparency film, envelopes, tab paper, and 
other special media.
For detailed information on paper that can be loaded in the bypass tray, see IMPORTANT POINTS ABOUT PAPER 
(page 1-27) in 1. BEFORE USING THE MACHINE. For precautions when loading paper in the bypass tray, see 
LOADING PAPER IN THE BYPASS TRAY (page 1-34) in 1. BEFORE USING THE MACHINE.
1
Place the original.
Place the original face up in the document feeder tray, or face 
down on the document glass.
When placing the originals on the document glass...
After placing the original, be sure to close the automatic 
document feeder. If left open, parts outside of the original will 
be copied black, causing excessive use of toner.
2
Place paper in the bypass tray.
Insert the paper with print side face down.
However, if the paper type is Letter Head or Pre-Printed, 
load the paper with the print side face up*.
* If Disabling of Duplex is enabled in the system settings 
(administrator), load the paper in the normal way (face up in 
trays 1 to 5; face down in the bypass tray).
When loading paper larger than A4R or 8-1/2 x 11R, be sure 
to pull out the bypass tray extension. Pull the bypass tray 
extension all the way out. If the bypass tray extension is not 
pulled all the way out, the size of the loaded paper will not be 
correctly displayed.
3
Touch the [Paper Select] key.
1 1
Special Modes
Plain2-Sided Copy
Output
File
Quick File
Copy Ratio
100%
A33.2.1.A4R
OriginalPaper SelectAuto
A4
PlainAuto
ExposureAutoB44.
A4A4
A4Preview
Downloaded From ManualsPrinter.com Manuals