Sharp MX M310 User Manual

							69
NETWORK SCANNER FUNCTION
4
RESTRICTING USE OF THE NETWORK SCANNER 
FUNCTION (USER AUTHENTICATION)
Use of the network scanner function can be restricted by means of user passwords stored in an LDAP server.
Settings required for user authentication
To implement user authentication, the following settings are required:
 Enable user authentication (step 3 on page 58)
 Configure LDAP server settings (p.60)
 Store login names (p.67)
Logging in when user authentication is enabled
To use the network scanner function when user authentication is enabled, you must first log in. Follow these steps:
1Press the [SCAN] key on the operation panel.
The login screen will appear in the touch panel.
If you will use the [SELECT FROM SENDER LIST] key, go to step 3.
2Touch the [LOGIN NAME] key, 
[E-MAIL ADDRESS] key.
A text entry screen will 
appear when each key is 
touched. Enter the 
LOGIN NAME, SENDER 
NAME, and E-MAIL 
ADDRESS. (Go to step 
4.)
3Touch the [SELECT FROM SENDER 
LIST] key.
The sender list screen 
appears. When you 
select your login name, 
sender name and e-mail 
address are entered.
4Enter the password.
For the password, enter the user password that is stored in the server.
5Touch the [OK] key.
If the login name and password are valid, the initial screen (p.70) of scanner mode appears.
JOB STATUS
COPY
PRINT
SCAN
FA X
ON LINE
D ATA
D ATA
LINE
D ATA
SYSTEM SETTINGS
USER AUTHENTICATION
SENDER NAME:
E-MAIL ADDRESS
LOGIN NAME
PASSWORD
OK
SELECT FROM
SENDER LIST
 To logout, press the [LOGOUT] key ( ). If audit mode is enabled, you will also log out of your account.
 To switch to a mode other than network scanner mode, you must log out.
SPACE12#$%
abcABC
AB/ab
CANCELOKPASSWORD
Note
Downloaded From ManualsPrinter.com Manuals 
						

							70
INITIAL SCREEN OF SCANNER MODE
The condition setting screen of scanner mode is displayed by pressing the [SCAN] key (refer to the operation 
manual for copier) while the copy mode, print mode, fax mode, or job status screen appears in the touch panel.
If user authentication is enabled, the initial screen will appear after authentication. (p.69)
In the explanations that follow, it is assumed that the initial screen that appears after pressing the [SCAN] key is the 
condition setting screen (shown below). If you have set the display to show the address book screen (following 
page) when the [SCAN] key is pressed, touch the [CONDITION SETTINGS] key in the address book screen to 
display the condition setting screen.
Condition settings screen
The display is initially set (factory setting) to show the following condition setting screen as the initial screen.
Message display
Messages appear here to indicate the current 
status of the machine.
[ADDRESS BOOK] key (p.71)
This displays the address book screen (next page). 
Touch this key when you wish to use a one-touch key 
that has a destination (or group) programmed in it.
[ADDRESS REVIEW] key (p.74)
When performing Scan to E-mail broadcast 
transmission, touch this key to check your selected 
destinations. A list of the destinations will appear, 
and you can delete any incorrect destinations.
[ADDRESS ENTRY] key (p.74)
When performing Scan to E-mail, touch this key if 
you wish to enter the e-mail address of the recipient 
manually instead of using a one-touch key.
[SEND SETTINGS] key (p.82)
Touch this key to change the subject*, file name, or 
sender* when sending a scanned image.
* When using Scan to E-mail.
[INFORMATION] icon (p.79)
The [INFORMATION] icon appears in the base 
screen when one or more special modes are 
selected.[ORIGINAL] key (p.76, 77, 78)
Touch this key to set the original size manually, 
select two-sided scanning, or select job build 
(when an RSPF is installed).
[FILE FORMAT] key (p.81)
Touch this key to change the format of the image 
file to be sent, or change the number of pages per 
file. The selected format is highlighted at the top of 
the key.
[RESOLUTION] key (p.80)
Touch this key to change the resolution setting for 
the original to be scanned. The selected resolution 
setting will be highlighted above the key. 
[QUALITY] key (p.79)
Touch this key to change the image quality and 
density settings for scanning. The selected image 
quality and density are highlighted at the top of the 
key.
The administrator setting DEFAULT DISPLAY SETTINGS can be used to set the display to show either the 
condition setting screen (shown below) or the address book screen (following page) when the [SCAN] key is 
pressed (refer to 6. SYSTEM SETTINGS (ADMINISTRATOR)).Note
ADDRESS
BOOK
READY TO SEND.
300dpi
AUTO
QUALITY
RESOLUTION
TIFF-G4FILE FORMAT
AUTOORIGINAL
ADDRESS ENTRY
ADDRESS REVIEW
SEND SETTINGS
1
10
9
8
7
6
2
3
4
5
1
2
3
4
5
6
7
8
9
10
Downloaded From ManualsPrinter.com Manuals 
						

							71
NETWORK SCANNER FUNCTION
4
Address book screen
Touch the [ADDRESS BOOK] key in the condition setting screen (previous page) to display the screen shown below 
at right.
Destinations stored using the Web page are grouped in indexes ( ) according to the letter entered in Initial for 
each destination, and the name entered in Display Name is displayed in the one-touch key ( ).
One-touch key display
This shows the one-touch keys that have been 
stored on the selected index card. The key type is 
indicated by the icon at the right.
:Scan to E-mail
:Scan to FTP
:Scan to Desktop
The number of one-touch keys that appear in one 
screen can be changed to 6, 8, or 12 using THE 
NUMBER OF DIRECT ADDRESS / SENDER 
KEYS DISPLAYED SETTING in the administrator 
settings.
Display switching keys
In cases where the one-touch keys cannot all be 
displayed on one screen, this shows how many 
screens are left. Touch the     keys to 
move through the screens.
[CONDITION SETTINGS] key
This displays the condition setting screen (p.70), 
which is used to set various conditions.
[GLOBAL ADDRESS SEARCH] key (p.75)
If an LDAP server is used, touch this key to select 
a Scan to E-mail destination in the LDAP server. If 
an LDAP server is not used, the key is greyed out 
and cannot be selected.[ABC GROUP] key
Touch this key to switch between the alphabetical 
index and the group index. The selected index type 
is displayed.
Index keys
One-touch key destinations are stored on each of 
these index cards (alphabetical index or group 
index). Touch an index key to display the card.
Group indexes make it possible to store one-touch 
keys by group with an assigned name for easy 
reference. This is done with the system settings 
(p.61). Frequently used one-touch key destinations 
can be stored on the [FREQUENT USE] card for 
convenient access.
6
1
USER 1USER 2USER 3USER 4USER 5USER 6ABCGROUP
ABCGROUPFREQUENT USEABCDEFGHIJKLMNOPQRSTUVWXYZ
TEST5TEST6
TEST7TEST8
TEST3
TEST1TEST2CONDITION
SETTINGS1/2
ADDRESS REVIEW
READY TO SEND.
GLOBAL
ADDRESS SEARCH
TEST4
E-mail Destination Management page
6
6
1
1234
56
1
2
3
4
5
6
 If the initial screen has been set to the address book screen in the administrator settings, the above screen will 
be the initial screen.
 If desired, you can use the administrator settings, DEFAULT DISPLAY SETTINGS, to set the default screen 
to the group index. (See 6. SYSTEM SETTINGS (ADMINISTRATOR).)Note
Downloaded From ManualsPrinter.com Manuals 
						

							72
SENDING AN IMAGE
BASIC TRANSMISSION METHOD
1Make sure the machine is in scanner 
mode.
When the [SCAN] key 
light is on, the machine is 
in scanner mode. If the 
light is not on, press the 
[SCAN] key.
If user authentication is 
enabled, you must log in. 
(p.69) 
2Load the original.
For detailed information 
on loading an original, 
refer to the operation 
manual for copier.
3Check the original size that appears in 
the top half of the [ORIGINAL] key.
The original size is 
automatically detected. 
If you loaded a 
non-standard size 
document or wish to 
change the scanning size, 
touch the [ORIGINAL] key 
and set the document 
size. (Refer to page 78.)
4Adjust the quality setting. (p.79)
The factory default 
settings are:
 Image quality: 
TEXT/PHOTO
 Density: AUTO
5Adjust the resolution setting. (p.80)
The factory default 
setting is 300dpi.
6Select the file format. (p.81)
The factory default 
settings are:
 FILE TYPE: TIFF

COMPRESSION MODE: 
MMR (G4)
PAGES PER FILE: ALL
7Touch the [ADDRESS BOOK] key.
The address book screen 
appears.
You cannot load documents in both the 
RSPF and on the document glass and send 
them in a single transmission. If documents 
are loaded in both the RSPF and on the 
document glass, only the document in the 
RSPF will be scanned and transmitted.
To scan a two-sided original (when an RSPF 
is installed), refer to page 76.
If you are scanning a large number of 
originals (and the RSPF is installed), follow 
the procedure on page 77.
 To rotate the document image 90° before 
transmission, see page 78.
JOB STATUS
COPY
PRINT
SCAN
FA X
ON LINE
D ATA
D ATA
LINE
D ATA
SYSTEM SETTINGS
Note
AUTO   A4
ORIGINAL
300dpi
RESOLUTION
TIFF-G4
FILE FORMAT
Note
AUTO A4
300dpiRESOLUTION
QUALITY
TIFF-G4
AUTO
FILE FORMAT
AUTO   A4ORIGINAL
300dpiRESOLUTION
QUALITY
TIFF-G4FILE FORMAT
AUTO   A4ORIGINAL
300dpiRESOLUTION
QUALITY
TIFF-G4FILE FORMAT
ADDRESS
BOOK
ADDRESS ENTRY
ADDRESS REVIEW
SEND SETTINGS
Downloaded From ManualsPrinter.com Manuals 
						

							73
NETWORK SCANNER FUNCTION
4
8Touch the one-touch key of the desired 
destination.
The key you touched is 
highlighted. If you touch 
the wrong key, touch the 
key again to cancel the 
selection. The key 
display will return to 
normal.
9Enter a file name for the scanned 
image. (p.82)
If the send settings are 
not changed, a file name 
is assigned based on the 
items specified in the 
Web page.
Using the RSPF
10Press the [START] key ( ).
Scanning begins. When 
scanning is finished, 
SENDING. PRESS [C] 
TO CANCEL. appears in 
the touch panel and 
transmission begins.
When transmission is 
finished, SENDING 
COMPLETED. appears 
in the touch panel.
Using the document glass
10Press the [START] key ( ).
The original is scanned 
and the [READ-END] key 
appears.
11If you have another page to scan, 
change pages and then press the 
[START] key ( ).
Repeat this sequence until all pages have been 
scanned. 
12After the final page is scanned, touch 
the [READ-END] key.
SENDING. PRESS [C] 
TO CANCEL. appears in 
the touch panel and 
transmission begins.
When transmission is 
finished, SENDING 
COMPLETED. appears 
in the touch panel.
 Refer to pages 62 to 65 for information on 
programming one-touch key destinations.
 When touching a one-touch key, 
corresponding information from the e-mail 
destination screen is shown in the 
message display.
 The destination e-mail address for Scan to 
E-mail can be entered manually, or you 
can search for a destination in an LDAP 
server on the network (p.74 to 75).
 Multiple destinations can be specified for 
a Scan to E-mail transmission (p.74).
When sending an image by Scan to E-mail, 
a subject and senders name can be 
entered.
Normally the subject and sender are 
automatically entered based on the 
information stored in Reply E-mail Address 
in SMTP Setup in the Web page.
If user authentication is enabled, the e-mail 
address of the user who logged in is used as 
the sender.
FREQUENT USEABCDEFGHIJKLMNOP
TEST5TEST6
TEST7TEST8
TEST3
TEST1TEST2
READY TO SEND.
TEST4
Note
ADDRESS
BOOK
ADDRESS ENTRY
ADDRESS REVIEW
SEND SETTINGS
Note
If no action is taken for one minute, scanning 
automatically ends and transmission begins.Note
READ-END
ESS [START].
EAD-END].
 To cancel transmission while SCANNING ORIGINAL. appears in the display or before the [READ-END] key 
is touched, press the [CLEAR] key ( ) or the [CLEAR ALL] key ( ). If you press the [CLEAR] key ( ), the 
destination and scan settings are saved. To cancel a transmission, press the [JOB STATUS] key and cancel 
the job. (p.83)
 If you exceed the number of pages that can be scanned while scanning an original, THE MEMORY 
BECOMES FULL. will appear in the touch panel. To send the data that has been scanned to that point, touch 
the [SEND] key. To cancel the transmission, touch the [CANCEL] key. 
 If a misfeed occurs while an original is being scanned, remove the original according to the instructions in the 
touch panel. To resume scanning after removing the misfeed, press the [START] key ( ).Note
Downloaded From ManualsPrinter.com Manuals 
						

							74
NETWORK SCANNER FUNCTION
TRANSMISSION METHODS FOR SCAN TO E-MAIL
The destination for a Scan to E-mail transmission can be selected from the address book or entered manually. You 
can also use an e-mail address stored on an LDAP server. 
It is possible to select multiple destinations for a Scan to E-mail transmission using a combination of these methods.
Use the following procedure when you wish to enter the e-mail address manually or use an e-mail address stored on 
an LDAP server.
Sending an image by entering an e-mail address manually
1Perform steps 1 through 6 of BASIC 
TRANSMISSION METHOD. (p.72)
2Touch the [ADDRESS ENTRY] key.
The e-mail address entry 
screen appears.
3Touch the keys on the keyboard to 
enter the e-mail address.
 If you make a mistake, touch the   key to move the 
cursor ( ) back to the mistake and then enter the 
correct character.
 To enter a number, touch the [AB/ab   12#$%] key. 
The screen will change to the number entry screen.
To return to the text entry screen, touch the [AB/ab 
 12#$%] key again.
4Touch the [OK] key.
5If you wish to enter another e-mail 
address, repeat steps 2 through 4.
If you wish to select an e-mail address from the 
address book screen, follow steps 7 and 8 of 
BASIC TRANSMISSION METHOD (p.72 to 73).
If you wish to select an e-mail address in an 
LDAP server, follow the steps in Sending an 
image by selecting an e-mail address in an LDAP 
server (p.75).
6Touch the [ADDRESS REVIEW] key 
and check the destinations.
When the [ADDRESS 
REVIEW] key is touched, 
only the entered 
destinations are displayed.
To delete a destination, 
touch the key of the 
destination that you wish 
to delete.
Touch the [OK] key to 
return to the initial screen.
7Continue from step 9 of BASIC 
TRANSMISSION METHOD (p.73).
ADDRESS
BOOK
ADDRESS ENTRY
ADDRESS REVIEW
SEND SETTINGS
SPACE12#$%
abcABC
AB/ab
CANCELOKE-MAIL ADDRESS
[email protected]
abcABC
CANCELOK
If you frequently transmit to a fixed group of 
destinations, you can store the destinations 
as a group (p.65).
The entered or selected destinations appear in 
the address review screen as one touch keys. 
A maximum of 18 characters of the name or 
e-mail address can appear in each key.
To cancel the operation when selecting 
destinations, press the [CLEAR ALL] key ( ).
Note
ADDRESS
BOOK
ADDRESS ENTRY
ADDRESS REVIEW
SEND SETTINGS
Note
Note
Important points when using Scan to E-mail
Be very careful not to send image data files that are too large. Your mail servers system administrator may 
have placed a limit on the amount of data that can be sent in one e-mail transmission. If this limit is 
exceeded, the e-mail will not be delivered to the recipient. Even if there is no limit and your e-mail is 
successfully delivered, a large data file may take a long time to be received and place a heavy burden on the 
recipients network, depending on the recipients network (Internet) connection environment. If large image 
data files are repeatedly sent, the resulting burden on the network may slow down the speed of other, 
unrelated data transmissions and in some cases, may even cause the mail server or network to go down. In 
cases where you need to send multiple documents, try such measures as lowering the resolution mode.
A limit can be set for the size of image files sent by Scan to E-mail in Maximum Size of File (p.58) in the Web page.
Caution
Downloaded From ManualsPrinter.com Manuals 
						

							75
NETWORK SCANNER FUNCTION
4
Sending an image by selecting an e-mail address in an LDAP server
To use an LDAP server, the LDAP server settings must be configured in the Web page.
1Perform steps 1 through 6 of BASIC 
TRANSMISSION METHOD. (
p.72)
2Touch the [ADDRESS BOOK] key.
The address book screen 
appears.
3Touch the [GLOBAL ADDRESS 
SEARCH] key.
The global address 
search screen appears.
4Touch the key of the server that you 
wish to search and then touch the 
[OK] key.
 If you make a mistake, touch the   key to move the 
cursor ( ) back to the mistake and then enter the 
correct character.
 To enter a number, touch the [AB/ab   12#$%] key. 
The screen will change to the number entry screen.
To return to the text entry screen, touch the [AB/ab 
 12#$%] key again.
5Touch the [OK] key.
The server begins searching.
When the search is finished, a list of the matching 
e-mail addresses appears.
6Touch the one-touch key of the 
desired destination.
If you touch the wrong 
key, touch the correct key.
7Touch the [ADD SELECTED] key.
The destination selected 
in step 6 is entered as a 
destination of the 
transmission.
8If you wish to enter another e-mail 
address, repeat steps 6 through 7.
If multiple LDAP servers have been configured and 
you wish to select a different server, touch the 
[ADDRESS BOOK] key and then touch the 
[GLOBAL ADDRESS SEARCH] key.
9Touch the [ADDRESS REVIEW] key 
and check the destinations.
When the [ADDRESS 
REVIEW] key is touched, 
only the entered 
destinations are displayed.
To delete a destination, 
touch the key of the 
destination that you wish 
to delete.
Touch the [OK] key to 
return to the initial screen.
10Continue from step 9 of BASIC 
TRANSMISSION METHOD (p.73).
If multiple LDAP servers have been 
configured, the server select screen appears.
Touch the key of the server that you wish to 
search and then touch the [OK] key.
The selected server key is highlighted.
ADDRESS
BOOK
ADDRESS ENTRY
ADDRESS REVIEW
SEND SETTINGS
ABCGROUPJKLMNOPQRSTUVWXYZ
CONDITION
SETTINGS1/2
ADDRESS REVIEW
GLOBAL
ADDRESS SEARCH
Note
1/2
CANCELOKSERVER SELECT
SERVER 1
SERVER 2
SERVER 3
SERVER 4
SPACE12#$%
abcABC
AB/ab
CANCELOKGLOBAL ADDRESS SEARCH
test
If there are no matches, touch the [OK] key 
in the message screen that appears. Touch 
the [SEARCH AGAIN] key and repeat the 
procedure from step 4.
To cancel the operation when selecting 
destinations, press the [CLEAR ALL] key ( ).
Note
test5test6
test3
test1
ADD SELECTED
tes
test2
READY TO SEND.
test4
test5test6
test3
test1
ADD SELECTED
tes
test2
No.001:test1
[email protected]
test4
CONDITION
SETTINGS
ADDRESS REVIEW
SEARCH AGAIN
ADDRESS BOOK
Note
Downloaded From ManualsPrinter.com Manuals 
						

							76
NETWORK SCANNER FUNCTION
SCANNING AND TRANSMITTING A TWO-SIDED 
ORIGINAL (when an RSPF is installed)
Follow these steps to automatically scan a two-sided original.
1Make sure the machine is in scanner 
mode and then load the document in 
the RSPF. (p.72)
2Touch the [ORIGINAL] key.
3Touch the [2-SIDED BOOKLET] key or 
the [2-SIDED TABLET] key as 
appropriate for the original you 
loaded.
If you wish to rotate the 
original 90° when 
creating an image file, 
touch the [ROTATE THE 
IMAGE 90 DEGREES] 
checkbox (a checkmark 
should appear in the 
box).
4Touch the [OK] key.
You will return to the 
initial screen.
5Continue from step 4 of BASIC 
TRANSMISSION METHOD (
p.72 to 73).
If the correct original size does not appear in 
the screen of step 2, touch the [MANUAL] 
key and specify the correct original size 
(p.78).
AUTO   A4
ORIGINAL
300dpi
RESOLUTION
TIFF-G4
FILE FORMAT
MANUAL
ROTATE THE 
AUTO
2-SIDED
BOOKLET2-SIDED
TABLET
ORIGINAL SIZE
Note
MANUAL
ROTATE THE IMAGE 90 DEGREES
OK
2-SIDED
TABLETJOB
BUILD
INAL SIZE
 Booklets and tablets
Two-sided originals that are bound at the side are booklets, and two-sided 
originals that are bound at the top are tablets.
 Two-sided scanning mode turns off after transmission is finished. Two-sided 
scanning mode can also be cancelled by pressing the [CLEAR ALL] key  
().NoteBooklet Tablet
Downloaded From ManualsPrinter.com Manuals 
						

							77
NETWORK SCANNER FUNCTION
4
SCANNING A LARGE NUMBER OF ORIGINALS (when 
an RSPF is installed)
If you have a large number of originals, the originals can be scanned in batches using the RSPF.
1Make sure the machine is in scanner 
mode and then load the document in 
the RSPF. (p.72)
2Touch the [ORIGINAL] key.
3Touch the [JOB BUILD] key.
If you wish to rotate the 
original 90° when creating 
an image file, touch the 
[ROTATE THE IMAGE 90 
DEGREES] checkbox (a 
checkmark should appear 
in the box).
4Touch the [OK] key.
You will return to the 
initial screen.
5Perform steps 4 through 9 of BASIC 
TRANSMISSION METHOD
. (p.72 to 73)
6Press the [START] key ( ).
Scanning of the originals 
begins. A message 
appears in the touch 
panel.
7When all of the originals in the RSPF 
have been scanned, load the next 
batch and press the [START] key ( ).
Repeat this sequence until all pages have been 
scanned.
8When all originals have been 
scanned, touch the [READ-END] key.
SENDING. PRESS [C] 
TO CANCEL. appears in 
the touch panel and 
transmission begins.
When transmission is 
finished, SENDING 
COMPLETED. appears 
in the touch panel.
If the correct original size does not appear in 
the screen of step 2, touch the [MANUAL] key 
and specify the correct original size (p.78).
AUTO   A4
ORIGINAL
300dpi
RESOLUTION
TIFF-G4
FILE FORMAT
MANUAL
ROTATE THE IMAGE 90 DEGREES
OK
2-SIDED
TABLETJOB
BUILD
RIGINAL SIZE
Note
MANUAL
ROTATE THE IMAGE 90 DEGREES
OK
2-SIDED
TABLETJOB
BUILD
NAL SIZE
If no action is taken for one minute, scanning 
automatically ends and transmission begins.Note
READ-END
ESS [START].
EAD-END].
 Job build mode turns off after transmission is finished. Job build mode can also be cancelled by pressing the 
[CLEAR ALL] key ( ).
 When performing Scan to E-mail, see the notes on page 74.Note
Downloaded From ManualsPrinter.com Manuals 
						

							78
SCANNING SETTINGS
(ORIGINAL SIZE, QUALITY, RESOLUTION, 
FILE FORMAT, AND SEND SETTING)
When sending an image, you can change the original scan size, quality, resolution, file format, and file name.
MANUALLY SETTING THE SCANNING SIZE
If you load an original that is not a standard size, or if you wish to change the scanning size, touch the [ORIGINAL] 
key and set the original size manually.
Perform the following steps after loading the document in the RSPF or on the document glass.
1Touch the [ORIGINAL] key.
2Touch the [MANUAL] key.
The sizes that can be 
selected are displayed.
3Touch the desired original size key.
[AUTO] is no longer 
highlighted. [MANUAL] 
and the original size key 
you touched are 
highlighted.
If you wish to select an inch size, 
touch the [AB INCH] key and then 
touch the desired original size key.
[INCH] is highlighted and 
inch size keys are 
displayed. To return to 
the AB size, touch the 
[AB INCH] key once 
again.
4Touch the outer [OK] key.
You will return to the 
initial screen.
Touching the inner [OK] 
key in the step above 
returns you to step 2.
5The selected size appears in the top 
half of the [ORIGINAL] key.
*Standard sizes:
The following originals sizes will be correctly detected:
 Countries/regions that use AB standard sizes: A3, A4, A4R, A5, A5R*, B4, B5, B5R.
 Countries/regions that use inch-based standard sizes:11x17, 8-1/2x14, 8-1/2x11, 8-1/2x11R, 
5-1/2x8-1/2, 5-1/2x8-1/2R*.
* These sizes can only be automatically detected when the RSPF is used.
If a non-standard size original is loaded (including special sizes), the closest standard size may be displayed, or 
the original size may not appear.Note
If you wish to rotate the original 90° when 
creating an image file, touch the [ROTATE 
THE IMAGE 90 DEGREES] checkbox (a 
checkmark should appear in the box).
 The [2-SIDED] key and [JOB BUILD] key 
do not appear on models that do not have 
an RSPF installed.
AUTO   A4
ORIGINAL
300dpi
RESOLUTION
TIFF-G4
FILE FORMAT
MANUAL
ROTATE THE IMAGE 90 D
O
DED
LET2-SIDED
TABLETJOB
BUIL
ORIGINAL SIZE
Note
AUTOMANUALOKORIGINAL SIZE
OKB5
A4R
A5R
A4
A5
B5R
INCH
AB
A3B4
You can return to automatic detection by 
pressing the [CLEAR ALL] key ( ).
5 X81 
/
 21 
/
 25 X8 R1 
/
 21 
/
 2
8 X11R1 
/
 28 X131 
/
 28 X141 
/
 28 X111 
/
 2
11X17
AUTOMANUALOKORIGINAL SIZE
OK
INCH
AB
MANUAL
OKINAL SIZE
OKB5
A4R
5R
4
INCH
AB
3
A4
ORIGINAL
300dpi
RESOLUTION
TIFF-G4
FILE FORMAT
A4
Note
Downloaded From ManualsPrinter.com Manuals