Sharp MX B200 User Manual

DIGITAL MULTIFUNCTIONAL
SYSTEM
OPERATION GUIDE
Page
MX-B200
MODEL
CONTENTS .......................... 2
INTRODUCTION .................. 3
LOADING PAPER ................ 9
INSTALLING THE 
SOFTWARE ....................... 14
COPIER FUNCTIONS ........ 25
PRINTER FUNCTIONS ...... 35
SCANNER FUNCTIONS .... 49
SPECIAL FUNCTIONS ...... 61
MAINTENANCE ................. 66
TROUBLESHOOTING THE 
UNIT ................................... 71
OPTIONAL EQUIPMENT.... 87
Downloaded From ManualsPrinter.com Manuals 

2
1
2
4
3
5
6
8
7
9
10
1INTRODUCTION
CONVENTIONS USED IN THIS 
MANUAL .......................................... 3
PART NAMES .................................. 4 
OPERATION PANEL ........................ 5
INDICATORS ON THE OPERATION 
PANEL .............................................. 6
POWER ON ..................................... 7
2LOADING PAPER
PAPER ............................................. 9
LOADING THE PAPER TRAY ........ 10
BYPASS FEED (including special 
paper)...

1
1
3
This chapter provides basic information for using the unit.
CONVENTIONS USED IN THIS MANUAL
• The explanations in this manual assume that a single pass feeder and lower paper 
tray are installed on the machine.
For some functions and procedures, the explanations assume that devices other 
than the above are installed.
 Wherever MX-xxxx appears in this manual, please substitute your model name 
for xxxx.
 Illustrations of driver screens and other computer screens show the screens that 
appear in...

1
4 PART NAMES
Interface
USB 
connector
Original cover
Toner cartridge
Photoconductive
drum
SPF (Peripheral device)
Exit area
3
4
5
6
2
8
9
12
16
17
18
Original guides
Document feeder trayPeep holeDocument
feeder cover
8
4
13
14
11
7
151
10
SPF scanning area
Document glass
Operation panel
Front cover
Paper tray 1
Paper tray 2
Multi-bypass tray
Side cover
Side cover open button1
2
3
4
5
6
7
8
9
Bypass tray paper guides
Paper output tray
Paper output tray extension
Pow er  sw it ch
Handle
Power cord...

1
5 OPERATION PANEL
Sort key and indicators
Use to select sort mode.
Exposure mode selector key and 
indicators
Use to sequentially select the exposure 
modes: AUTO, MANUAL or PHOTO. 
Selected mode is shown by a lit 
indicator. (p.28)
Light and dark keys and indicators
Use to adjust the MANUAL or PHOTO 
exposure level. Selected exposure level 
is shown by a lit indicator. (p.28) Use to 
star t and terminate user program 
setting. (p.63)
Alarm indicators
Developer replacement required 
indicator (p.86)...

1
6
INDICATORS ON THE OPERATION PANEL
The start ( ) indicator indicates the state of the printer or scanner.
Start indicator
On: Indicates the unit is ready for copying or scanning is being performed.
Blinking: The indicator blinks in the following situations:
 When a print job is interrupted.
 When reserving a copy job.
 When toner is being replenished during a copy or print job.
Off: The indicator is off in the following situations:
 During copying or scanning.
 The unit is in the auto power shut-off...

1
7 POWER ON
Turn the power switch on the left side of the unit to the ON position. The start ( ) 
indicator will light up and other indicators which show the initial settings of the 
operation panel will also light up to indicate the ready condition. For the initial 
settings, see Initial settings of operation panel (p.8).
About the scan head
The scan head lamp remains on constantly when the unit is in the ready condition 
(when the start ( ) indicator is illuminated).
The unit adjusts the scan head...

1
8
Initial settings of operation panel
When the unit power is on, the operation panel will revert to the initial settings when 
the time set with the Auto clear time setting (p.63) elapses after a job is finished, or 
when the clear key is pressed twice.
The initial settings of the operation panel are shown below.
When copying has begun in this state, the settings in the following table are used.
Power off methods
If not used for a certain period of time, the unit will automatically enter auto power...

2
2
9
Follow the steps below to load paper into the tray.
PAPER
For best results, use only paper recommended by SHARP.
*1 Do not use non-standard envelopes, and envelopes that have metal clasps, 
plastic snappers, string closures, windows, linings, self-adhesive, patches or 
synthetic materials. Do not use envelopes that are filled with air or envelopes that 
have labels or stamps attached. These will cause physical damage to the unit.
*2 For paper weighing from 105g/m2 to 128g/m2 , A4 is the maximum...

2
10 LOADING THE PAPER TRAY
1Raise the handle of the paper tray 
and pull the paper tray out until it 
stops.
2Adjust the paper guides on the paper tray to the copy paper 
width and length. Squeeze the lever of paper guide   and slide 
the guide to match with the width of the paper. Move paper 
guide   to the appropriate slot as marked on the tray.
3Fan the paper and insert it into the tray. Make sure the edges go 
under the corner hooks.
Do not load paper above the maximum height line ( ). Exceeding...