Sharp LC-70LE735U Hdtv Owners Guide

							39
■Updating the Software via the Network
1 Press 
a/
bon the Manual Update screen to select 
"Network Update", and then press ENTER.
•  The TV connects to the network and checks for updates.•  To cancel, press ENTER.
Abort Connecting to Internet..
Checking for the latest software version..
Accessing..
2  The current version of the TV and the latest version 
of software are displayed. To update the TV 
software, select “Yes”, and then press ENTER.
Latest software version has been found.
A software update is available.
Proceed with update?
Update time may change depending on the network environmentCurrent Version
 XXXXXXXX
Latest Version
 XXXXXXXX
Estimated Update Time
 XX
NoYe s
•  When a server connection cannot be established or an 
update is not available, a message is displayed.
If a server connection cannot be established, check the 
broadband connection and Internet Setup.
Cannot reach the server.
Check the network settings and try again.
OK
OK
The TV does not need to be updated.
3  After the update fi le is downloaded, the software 
update process begins.
Downloading the latest software..
30%Abort Update Version
 XXXXXXXX
50%
Do not unplug AC cord. Remote control operation is disabled during update process.
Updating to the latest software..
Update Version
 XXXXXXXX
CAUTION
•Do not unplug the AC cord while the software is 
being updated.
4  When the software is successfully updated, a 
screen is displayed indicating that the update 
process is completed.
A screen indicating that the update is completed 
is displayed. 4 seconds later, the TV restarts 
automatically.
Software update is complete.
Update Version
 XXXXXXXX
•  If the software was not updated successfully, check the 
broadband connection and Internet Setup, and then try 
updating the software again.
OK Failed to complete update.
Please retry from Software Update menu.
■Updating the Software with a USB Memory DeviceTo check for the availability of a software update, visit
http://www.sharpusa.com/products/support/. If you 
have any questions, please
call 1-800-BE-SHARP (800-237-4277).
CAUTION
•  Do not remove the USB memory device or unplug 
the AC cord while the software is being updated.
•  Be sure to properly follow the whole procedure 
described below, step by step. Otherwise, for 
example, the TV cannot read the data in the USB 
memory device and software updating will fail.
1  Insert the USB memory device with the update fi le 
into the USB 1 or USB 2 terminal on the TV.
•  When you update the software, use only one USB 
terminal. Either USB 1 or USB 2 is usable.
or
2 Press 
a/
b on the Manual Update screen to select 
"USB Update", and then press ENTER.
On-Screen Display Menu
-$-&6@&JOEC


-$-&6@&JOEC








 
						

							40
3 Press ENTER to start checking the data in the USB 
memory device.
Insert the USB memory device 
containing the software update file.
OK
4  During the data checking, “Checking” blinks.
Now checking the data 
in the USB memory device.
Checking
•  The current version of the TV software and the version 
of the update fi le on the USB memory device are 
displayed.
Example
Software update file is detected 
in the USB memory device.
Start update?
NoYe sCurrent Version                  :  UXXXXXX1
Update Version                  :  UXXXXXX2
•  If the USB memory device is not properly installed or 
the correct update fi le cannot be found on the USB 
memory device, an error message is displayed.
  Check the fi le on the USB memory device, and then 
reinsert the USB memory device correctly.
Software update file is not detected in the USB memory device.
Confirm that you have transferred the file
to the USB memory device and retry software update.
OK
There is more than one software file in the USB memory device.
Confirm that only the software update file is 
in the USB memory device.
OK
On-Screen Display Menu
5  To update the TV software with the update fi le, 
select “Yes”, and then press ENTER.
Software update file is detected 
in the USB memory device.
Start update?
NoYe sCurrent Version                  :  UXXXXXX1
Update Version                  :  UXXXXXX2
Example
30% Now updating
Update Version                  :  UXXXXXX2
Do not unplug AC cord. Remote Control operation is disabled during Update process.
CAUTION
•Do not remove the USB memory device or unplug 
the AC cord while the software is being updated.
6  When the software is successfully updated, a 
screen is displayed indicating that the update 
process is completed.
  After this screen is displayed, the TV automatically 
turns off and then turns on again.
Example
Software update is complete.
OK Update Version                  :  UXXXXXX2
•  If the update has failed, check the fi le in the USB 
memory device and try Software Update again.
Failed to complete update.
Retry Software Update.
If system Update fails again,
contact the customer service center.
OK Update Version                  :  UXXXXXX2
7  After the screen shown below is displayed, press 
ENTER.
System software was 
successfully updated.
Remove the USB memory device.
OK
8  Remove the USB memory device.
-$-&6@&JOEC


-$-&6@&JOEC








 
						

							
41
CAUTION
•The 3D Glasses are precision equipment. Handle them with care.
• Improper use of the 3D Glasses or failure to follow these instructions c\
an result in eye strain.
• If you experience dizziness, nausea, or other discomfort while viewing 3\
D images, immediately discontinue use 
of the 3D Glasses. Using the 3DTV with incompatible 3D broadcasts or sof\
tware can make images appear blurry 
or create overlapping images.
• When viewing 3D images continuously, be sure to take a break periodicall\
y to prevent eye strain.
• If you are nearsighted or farsighted or have astigmatism or a different \
level of eyesight between the left and right 
eyes, you should take the necessary steps, such as wearing eyeglasses, t\
o correct your eyesight before viewing 
3D images. The 3D Glasses can be worn over eyeglasses.
• When viewing 3D images, keep the 3D Glasses horizontally level with the \
TV screen. If you tilt the 3D Glasses 
with respect to the TV screen, the images viewed by the left and right e\
yes may appear signifi  cantly different or 
images may appear overlapping.
• View 3D images at the appropriate distance from the TV screen. The recom\
mended distance is three times the 
effective height of the TV screen.
  Examples of recommended distances
  70-inch screen: Approx. 8.5 ft (2.6 m) Viewing should not be done closer than the recommended distance.
• Be careful of your surroundings when viewing 3D images. When you view 3D\
 images, objects may appear 
closer or farther than they are. This may cause you to misjudge the dist\
ance and possibly result in injury if you 
accidentally hit the screen or surrounding objects. 
• The 3D Glasses are not recommended for people aged less than 6.
• When children are viewing 3D images, be sure a parent or guardian is pre\
sent. Monitor children viewing 3D 
images, and if they show signs of discomfort, immediately discontinue us\
e of the 3D Glasses.
• People with a known history of photosensitivity and people with heart pr\
oblems or poor health should not use 
the 3D Glasses. This can worsen existing health conditions.
• Do not use the 3D Glasses for other purposes (such as general eyeglasse\
s, sunglasses, or protective goggles).
• Do not use the 3D function or 3D Glasses while walking or moving around.\
 This may result in injuries due to 
running into objects, tripping, and/or falling.
•
When using the 3D Glasses, take care not to accidentally strike the TV s\
creen or other people. Viewing 3D images may 
cause you to misjudge the distance to the TV screen and accidentally str\
ike the screen, resulting in possible injury.
• It is recommended that you do not view 3D images if you are sleep depriv\
ed or if you have been drinking alcohol.
Display Methods for 3D and 2D Images
Display method Example display Description
3D mode 
(using the 3D 
Glasses) 2D
➝ 3D
• Converts normal 2D images into 3D images.
Side by Side
• Creates 3D images from 3D images displayed side  by side. The image is split into a left and right image, 
and then the images are stretched and displayed 
sequentially to create a 3D image.
Top and Bottom
• Creates 3D images from 3D images displayed on  the top and bottom. The image is split into a top and 
bottom image, and then the images are stretched and 
displayed sequentially to create a 3D image.
2D mode 
(without using 
the 3D Glasses) Side by Side 
➝ 2D
• Creates 2D images from 3D images displayed side by 
side. Only the left image is stretched and displayed. The 
image does not appear in 3D.
Top and Bottom  ➝ 2D
• Creates 2D images from 3D images displayed on the 
top and bottom. Only the top image is stretched and 
displayed. The image does not appear in 3D.
Enjoying 3D Image Viewing
You can use special 3D Glasses to watch 3D-supported images on this TV.•  You can enjoy 3D movies on this TV by viewing the movie through SHARP 3D\
 Glasses sold separately.
•  To produce 3D images, liquid crystal shutters in the 3D Glasses alternat\
ely open and close imperceptibly fast to exactly  match alternating left and right video images displayed by the TV.
•  Not all consumers can experience and enjoy 3DTV. Some people suffer from\
 stereo blindness which prevents them from  perceiving the intended depth of 3D entertainment. Also, some people who\
 watch 3D programming may experience initial 
feelings of motion sickness as they adjust to the picture. Others may ex\
perience headaches, eye fatigue or motion sickness. 
Some viewers might also experience epileptic seizures. Like a roller coa\
ster, the experience is not for everyone.
-$-&6@&@JOEE


-$-&6@&@JOEE








 
						

							42
Switching from 3D to 2D Mode
4 Press 3D during the 3D mode.
  Select “Yes” and press ENTER to switch to 2D 
mode.
NoYe s
• Take off the 3D Glasses and turn off the power.
Ending 3D Image Viewing
5  Take off the 3D Glasses and turn off the power.
•  If the input signal switches to 2D, 2D images are displayed 
automatically.
•  3D mode is canceled automatically when the setting is 
changed, input selection is changed, or the power is 
turned off.
Receiving a 3D Image Signal That Cannot 
Be Detected Automatically
1 Press 3D.
•  A screen appears prompting you to select between 3D 
and 2D image viewing.
2D3D
2 Press 
c/
d to select “3D” or “2D”, and then press 
ENTER.
•To view in 3D mode: Select “3D”, and then go to step 3.•To view in 2D mode: Select “2D”, and then go to step 6.
3 Press 
c/
d to select the 3D signal type ( “2D
➝3D”,
“Side by Side” or “Top and Bottom”) and then press 
ENTER.
Select to convert regular 2D picture to 3D.
2D -> 3D Side by Side Top and Bottom
•  If you select the same system as that of the input signal, 
3D images are displayed.
4  Turn on the 3D Glasses and place them on your 
head.
5  You can now view 3D images.
Viewing 3D Images
•  The TV screen may temporarily become black when the TV 
is trying to detect a 3D image signal and when switching 
from 3D to 2D mode.
Receiving a 3D Image Signal That Can Be 
Detected Automatically
The image signal may contain a 3D identifi cation 
signal. You can enable the TV to automatically detect 
the 3D image type by selecting “System Options” > “3D 
Setup” > “3D Auto Change” on the TV. (See page 44.)
1When “3D Auto Change” is set to “Yes”
•
The 3D image type is detected automatically and the 
appropriate 3D image is displayed.
Changed to 3D mode. Put on 3D glasses
and press the power button on the glasses. 
If you are in bad physical conditions 
or feel uncomfortable watching 3D picture 
please stop watching TV.
3D
  When “3D Auto Change” is set to “No”
•
The following message is displayed. Press 3D.
3D picture is detected. 
Press the power button on the 3D glasses.
(Need to wear the 3D glasses to watch 3D picture)
•Press
c/
d to select the "Yes", and then press ENTER.
NoYe s
2  Turn on the 3D Glasses and place them on your 
head.
3  You can now view 3D images.
Enjoying 3D Image Viewing
-$-&6@&JOEC


-$-&6@&JOEC








 
						

							43
Switching from 3D to 2D Mode
6 Press 
c/
d to select the 2D signal type ( “Side by 
Side” or “Top and Bottom”) and then press ENTER.
Select when two images are displayed next to each other.
Side by Side Top and Bottom
•  If you select the same system as that of the input signal, 
2D images are displayed.
• Take off the 3D Glasses and turn off the power.
Ending 3D Image Viewing
7Take off the 3D Glasses and turn off the power.
Watching 2D Images in 3D
You can convert normal 2D images into 3D images.
1 Press 3D.
2 Press 
c/
d to select “2D
➝3D convert”, and then 
pressENTER.
3  Turn on the 3D Glasses and place them on your 
head.
•  The TV returns to 2D mode after 1 hour has passed.
Switching to the Previous Mode
You can switch back to the previous mode by pressing 3D.
1 Press 3D.• A confi rmation screen is displayed.
NoYe s
2  Select “Yes” and then press ENTER.• The TV returns to the previous mode.
3D Menu
Pressing3D in 3D mode displays the 3D menu. Press 
the colored buttons to make the necessary settings.
A: 3D Brightness Boost
B:3D Surround (See page 29.)
The surround mode changes each time you press B.
C:2D
➝3D Convert Effect (See page 44.)
D: 3D Setup (See page 44.)
Confi guring the TV Settings to 
Enhance 3D Image Viewing
MenuPicture
Settings
AV MODE (Changing Pic.Quality)[STANDARD (3D)]OPC[Off]
3D Brightness Boost[Middle]
Backlight[b5]a16b16
Contrast[b30] 0
b40
Brightness[0]
a30b30
Color[b2]a30b30
Tint[0]a30
b30
Sharpness[b2]a10
b10
Advanced
Picture Settings
Example
1 Press MENU to display the MENU screen, and then 
press
c/
d to select “Picture Settings”.
2 Press 
a/
b to select a specifi c adjustment item, 
and then press ENTER.
3 Press 
a/
b (or 
c/
d) to select the desired item, 
and then press ENTER.
4 Press MENU to exit.
•  Which items can be selected/adjusted differs depending 
on whether the TV is in 2D mode or in 3D mode.
AV MODE
The audio and video settings can be changed to suit 
the program or input content being watched.
STANDARD(3D):For a highly defi ned image in a normal 
lighting.
MOVIE(3D):For a movie.
GAME(3D):Lowers image brightness for easier viewing.
•  You can select AV MODE by pressing AV MODE on the 
remote control unit.
3D Brightness Boost
You can adjust the backlight of the TV for 3D image 
viewing.
High/Middle/Low:Select a desired level of 3D 
Brightness Boost.
•  When "High" or "Low" is selected, "OPC", "Backlight" and 
"Range of OPC" are not available.
Enjoying 3D Image Viewing
-$-&6@&JOEC


-$-&6@&JOEC








 
						

							44
3D Setup
You can make various settings to enhance 3D image viewing.
Menu
View Option System Options
System
Options
3D Setup
Input Terminal Setting AQUOS LINK Setup
Example
1 Press MENU to display the MENU screen, and then 
press
c/
d to select “System Options”.
2 Press 
a/
b to select “3D Setup”, and then press 
ENTER.
3 Press 
a/
b to select a specifi c item, and then press 
ENTER.
4 Press 
a/
b (or 
c/
d) to select the desired setting, 
and then press ENTER.
5 Press MENU to exit.
3D Auto Change
This setting can be used to switch to 3D mode 
automatically when a 3D identifi cation signal is 
detected.
Yes: When a 3D signal is detected, 3D mode is selected 
automatically.
No: Auto change is not performed.
•  3D signal may not be detected depending on the signal 
format.
2D➝3D Convert Effect
You can adjust the 3D effect when converting images 
from 2D mode to 3D mode.
Select a desired level of convert effect from +1 to +16.
•  This function is only available when converting 2D images 
to 3D images.
•  When you use this function, image conversion on the TV 
will result in some differences in the original images and 
how they appear.
•  2D images that have been converted to 3D images may be 
viewed only for personal use.
3D Still Image Effect Setting
Select the method for adjusting the 3D still image 
effect (depth).
Auto: Adjusts the still image effect (depth) automatically.
Manual: Manually adjust the still image effect (depth).
•  If you selected "Manual", adjust the 3D still image effect 
(depth) with "3D Still Image Effect Adjustment".
•  This function can be adjusted when viewing 3D still images 
in USB mode.
•  Even if you selected "Auto", the 3D still image effect (depth) 
may not be correctly adjusted depending on the 3D still 
image.
•  3D still images taken in macro mode will be displayed with 
excessive depth.
•  If you experience discomfort while viewing 3D images, 
immediately discontinue viewing.
3D Still Image Effect Adjustment
You can adjust the 3D still image effect (depth).
Adjust the level from –5 to +10. "0" is the level where 
no adjustment is made (factory preset value).
•  This function can be adjusted when viewing 3D still images 
in USB mode.
•  If you experience discomfort while viewing 3D images, 
immediately discontinue viewing.
Viewing Time Info
This displays the elapsed time of 3D image viewing.
Yes:Displays the elapsed viewing time on the screen 
every hour.
No:Does not display the elapsed viewing time.
3D Test
This displays 3D images for testing the 3D operation. 
Clicking "Start" on the screen plays back 3D test 
images.
•  If you press RETURN during playback, the previous 
screen will be displayed.
3D Glasses Control
To enable this function, set "TV Location" to "Store".
Selecting "Yes" prevents the 3D Glasses from receiving 
3D signals from other TVs.
Enjoying 3D Image Viewing
-$-&6@&JOEC


-$-&6@&JOEC








 
						

							45
Enjoying 3D Image Viewing
•  Appropriate 3D Glasses (sold separately) are required to view 3D images. Purchase 3D Glasses for use with Sharp brand 3D 
LCD TVs.
■3D Glasses lenses•  Do not apply pressure to the lenses of the 3D Glasses. Also, do not drop or bend the 3D Glasses.
•  Do not scratch the surface of the lenses of the 3D Glasses with a pointed instrument or other object. Doing so may damage 
the 3D Glasses and reduce the quality of the 3D image.
•  Use only the cloth provided with the optional 3D Glasses to clean the lenses.
■3D Glasses infrared receiver•Do not allow the infrared receiver to become dirty, and do not attach stickers to or otherwise cover the infrared receiver. Doing
so may prevent the receiver from operating normally.
•If the 3D Glasses are affected by other infrared data communication equipment, the 3D images may not be displayed correctly.
■Caution during viewing •Do not use devices that emit strong electromagnetic waves (such as cellular phones or wireless transceivers) near the 3D 
Glasses. Doing so may cause the 3D Glasses to malfunction.
•The 3D Glasses cannot operate fully at extreme high or low temperatures. Please use them within the specifi ed usage 
temperature range.
•If the 3D Glasses are used in a room with fl uorescent lighting (60 Hz), the light within the room may appear to fl icker. In this
case, either darken or turn off the fl uorescent lights when using the 3D Glasses.
•Wear the 3D Glasses correctly. 3D images will not be correctly visible if the 3D Glasses are worn upside down or back-to-front.•Other displays (such as computer screens, digital clocks, and calculators) may appear dark and diffi cult to view while wearing 
the 3D Glasses. Do not wear the 3D Glasses when watching anything other than 3D images.
•If you lie on your side while watching the TV with 3D Glasses, the picture may look dark or may not be visible.•Be sure to stay within the viewing angle and optimum TV viewing distance when watching 3D images. Otherwise, you may not 
be able to enjoy the full 3D effect.
•The 3D Glasses may not work properly if there is any other 3D product or electronic devices turned on near the glasses or TV. If
this occurs, turn off the other 3D product or electronic devices or keep the devices as far away as possible from the 3D Glasses.
•Stop using the 3D Glasses in any of the following situations:
–  When images consistently appear doubled while you are wearing the 3D Glasses
–  When you have diffi culty perceiving the 3D effect
•If the 3D Glasses are faulty or damaged, stop using them immediately. Continued use of the 3D Glasses may cause eye 
fatigue, headaches and illness.
•If you have any abnormal skin reaction, stop using the 3D Glasses. In very rare instances, such reactions may be due to an 
allergic reaction to the coating or materials used.
•If your nose or temples become red or you experience any pain or itchiness, stop using the 3D Glasses. Pressure caused by 
long periods of use may lead to such reactions and may result in skin irritation.
■Usage range of the 3D Glasses•  The 3D Glasses can be used by receiving an infrared signal sent from the TV.
 Operating range:
  From directly in front of the 3D infrared emitter on the TV: approx. 17 ft (5 m)
  (within approx. 30° horizontally and 20° vertically)
–  The 3D infrared emitter lights in 3D mode.
•  For further details, refer to the operation manual of your 3D Glasses.
-$-&6@&JOEC


-$-&6@&JOEC








 
						

							46
Enjoying Photo/Music/Video Playback
You can connect the TV to a USB memory device, USB hard drive or home network (DLNA) server to enjoy 
viewing pictures, listening to music, and watching videos.
•  Depending on the USB memory device/USB hard drive/home network (DLNA) server, the TV may not be able to recognize the 
recorded data.
•  It may take time to read the recorded data if the USB memory device/USB hard drive/home network (DLNA) server contains 
many fi les or folders.
•  Use only alphanumeric characters for naming fi les.
•  File names over 80 characters (may vary depending on character set) may not be displayed.
Connecting a USB Memory Device/USB Hard Drive
Insert the USB memory device with recorded photos, music or videos into the USB 1 or USB 2 terminal on the TV.•  If USB memory devices are inserted into both terminals, the USB 1 terminal has priority.
or
•  When connecting a USB hard drive, be sure to use a hard drive with an AC adapter.
•  Do not remove a USB memory device or memory card from the TV while transferring fi les, using the slide show function, or 
switching screens, or before you exit "USB" from the INPUT list.
•  Do not insert and remove a USB memory device/USB hard drive to and from the TV repeatedly.
•  When using a card reader, be sure to insert Memory fi rst before using the card reader.
•  USB input cannot be selected when displaying the browser. Close the browser fi rst.
CAUTION
•  Do not use a USB extension cable when connecting a USB memory device to the USB terminal on the TV.
• Using a USB extension cable with the USB memory device may prevent the TV from performing correctly.
Connecting a Home Network (DLNA) Server
Connect the TV to the home network (DLNA) server using an ETHERNET cable.
Home network (DLNA) serverETHERNET cable
Router
•  Do not disconnect a home network (DLNA) server from the TV while transferring files, when a screen is switching to another or 
before you exit "Home Network (DLNA)" from the INPUT list.
•  Do not connect and disconnect a home network (DLNA) server from the TV repeatedly.
-$-&6@&JOEC


-$-&6@&JOEC








 
						

							47
Select the Files to Play Back
•  To play back data on a USB memory device, insert the 
USB memory device on the TV. USB mode is selected 
automatically. (Go to step 2)
•  Use the following procedure to switch back to USB mode 
after switching from USB mode to another mode.
1   Select "USB" or "Home Network (DLNA)" from 
INPUT list screen.
2   Press D.
■ USB memory device
Pressa
/
b/c
/d
 to select the drive where you 
want to fi nd your fi les, and then press ENTER.
Drive1Drive2
Drive5 Drive6Drive3 Drive4
Example
•  If the TV is turned off and then on again, the number 
assigned to the USB drive may change.
■ Home Network (DLNA)
Pressa
/
b to select the server where you want to 
find your files, and then press ENTER.
Server1
Server2
Example
3   Press 
c/
d to select "Photo", "Music" or "Video", 
and then press ENTER.
Music
Photo
Video
Example
4   Press 
c/
d to select the desired folder, and then 
pressENTER.
•  You cannot switch the input mode if a USB memory device 
is not connected.
•  You do not need to select the drive/server in step 2 when 
there is only one drive in the connected USB memory 
device or there is only one home network (DLNA) server 
connected to the TV.
•  16 is the maximum number of USB drives and 10 is the 
maximum number of home network (DLNA) servers that 
can be displayed.
•  "VIEW MODE" is fi xed during the Photo or Music mode. 
During "Video mode", you can select "Auto" or "Original".
•  The key guide display disappears automatically after a 
set time. To display the key guide display again, press 
DISPLAY.
■ When displaying the data with the APPS
The Media screen can be displayed even by using the 
application window.
1   Press APPS to display the application window.
2   Press a
/
b/
c/
d to select "USB Media" or "Home 
Network (DLNA)", and then press ENTER.
• If "" is displayed after you switch to USB mode, 
check the USB connection.
• If "
" is displayed after you switch to Home Network 
(DLNA) mode, check your TV's network settings and 
connection.
•  You can also display the Media screen by pressing 
FAV APP on the remote control unit. See page 35 for 
details on the FAV APP Key Assign function.
Enjoying Photo/Music/Video Playback
-$-&6@&JOEC


-$-&6@&JOEC








 
						

							48
Enjoying Photo/Music/Video Playback
Playing Back Files on a USB 
Memory Device
Photo Mode
Viewing Thumbnails
... ...picture 5picture 4picture 2picture 1picture 3
Example
Buttons for thumbnail operations
Buttons Description
a/
b/
c/
dSelect a desired item.
ENTERDisplay the photo.
RETURNReturn to the previous process.
A (red)Select the images to be displayed. Press 
this button to add or remove a checkmark.
B (green)Display the music list screen.
C (blue)Start the slide show.
D (yellow)Display the USB MENU screen.
•  When there are invalid photo fi les, the X mark will be 
displayed for the fi le.
• The icon 
 appears on the thumbnails of 3D images. If 
you do not switch to 3D mode for the 3D images, they will 
be displayed in 2D.
•  You can see the fi le name, shooting date, fi le size and pixel 
size of the selected photo in the lower-left corner of the 
screen (shooting date is only available in the EXIF fi le format).
Viewing Individual Photos
The photo selected on the thumbnail selection screen 
is displayed.
Buttons for individual display operation
Buttons Description
c/
dGo to the previous/next photo in the same 
directory.
RETURNReturn to the thumbnail selection screen.
3DSwitches between 2D and 3D modes.
A (red)Rotate the photo by 90 degrees to the left.
B (green)Rotate the photo by 90 degrees to the right.
•  Rotating photos only applies to the temporarily selected 
item and this setting is not saved.
•  The key guide display disappears automatically after a 
set time. To display the key guide display again, press 
DISPLAY.
Slide Show
The photos displayed on the thumbnail selection 
screen are displayed as a slide show.
Buttons for slide show operation
Buttons Description
RETURNReturn to the thumbnail selection screen.
3DSwitches between 2D and 3D modes.
D (yellow)Display the USB MENU screen.
•  The selected BGM is played repeatedly.
•  The slide show continues until you press RETURN.
•  For setting the slide show speed, select "Select Slide Show 
Interval" on the USB MENU screen.
•  The key guide display disappears automatically after a 
set time. To display the key guide display again, press 
DISPLAY.
USB Menu
Remove USB Device
[10sec] Select Slide Show Intrerval
Select Slide Show BGM
Set All Slide Show Image
Reset All Slide Show Image
[On]
3D DisplayUSB MENU
Example
■ 3D Display
You can view photos in 3D.
1   Press D to display the USB MENU screen.
2   Press a
/
b to select "3D Display", and then press 
ENTER.
3   Press c/
d to select "On", and then press ENTER.
•  In 3D mode, you cannot rotate the photos.
•  You can select "3D display" from "USB MENU" only when 
the thumbnails screen for the photo mode in USB mode is 
displayed on the screen.
-$-&6@&JOEC


-$-&6@&JOEC