Sharp LC-70LE735U Hdtv Owners Guide

							
9
QUICK INSTALLATION TIPS
1Attach your antenna to the back of the television. 
(See page 10.)
2Connect the AC plug for the television into the AC 
outlet.
AC outlet
2
1
1
•  Place the TV close to the AC outlet, and keep the power plug within reach.
•  TO PREVENT RISK OF ELECTRIC SHOCK, DO NOT 
TOUCH UN-INSULATED PARTS OF ANY CABLES 
WITH THE AC CORD CONNECTED.
3When turning on the TV for the fi rst time, press 
POWER  on the television.
POWER
4Insert the batteries into the remote control unit. (See 
page 10.)
•  Speakers cannot be detached from the TV.
•  The TV angle cannot be adjusted.
QUICK REFERENCE
Experiencing HD Images
An HDTV without an HD source is just an ordinary 
TV.
To enjoy HD images on the TV, you should get 
HD programming from the following:
•  Over-the-air broadcasting via HD quality antenna
•  HD cable/satellite subscription
•  HD compatible external equipment
•  For information on updating to HD programming, ask your 
cable/satellite service provider.
Using the Remote Control Unit
Use the remote control unit by pointing it towards the 
remote control sensor on the TV. Objects between the 
remote control unit and the remote control sensor may 
prevent proper operation.
30º 30º
30º
30º
17´ (5 m)Remote control sensor
■  Cautions regarding the remote control unit
•  Do not expose the remote control unit to shock. In addition, 
do not expose the remote control unit to liquids, and do not 
place in an area with high humidity.
•  Do not install or place the remote control unit under direct  sunlight. The heat may cause deformation of the remote 
control unit.
•  The remote control unit may not work properly if the remote  control sensor on the TV is under direct sunlight or strong 
lighting. In such cases, change the angle of the lighting 
or the TV, or operate the remote control unit closer to the 
remote control sensor.
IMPORTANT:
IF THE UNIT DOES NOT POWER ON - UNPLUG THE 
TELEVISION FROM THE OUTLET AND REPEAT THE 
INSTALLATION STEPS.
IF YOU STILL ENCOUNTER NO POWER, PLEASE CONTACT 
US AT 1-800-BE-SHARP.
-$-&6@&@JOEE


-$-&6@&@JOEE








 
						

							10
Antennas
To enjoy a clearer picture, use an outdoor antenna. The following is a brief explanation of the types of connections 
that are used for a coaxial cable. If your outdoor antenna uses a 75-ohm coaxial cable with an F-type connector, 
plug it into the antenna terminal at the rear of the TV set. For connecting the antenna cable to the TV, use 
commercially available cables.
300-ohm twin-lead cable 75-ohm coaxial cable (round)
75-ohm coaxial cableINOUT
300-ohm
twin-lead cable VHFANTENNAUHF
ANTENNA
Combiner
To TV antenna 
terminal
300/75-ohm adapter300-ohm twin-lead cable (flat) 75-ohm coaxial cable (round)
Cable TV lead-In
Coaxial cable
Coaxial cable Home Antenna
terminal (75-ohm) Home Antenna
terminal (75-ohm)
or
or
Installing Batteries in the Remote Control Unit
If the remote control fails to operate TV functions, replace the batteries in the remote control unit.
1Open the battery cover.
2  Insert two “AAA” size batteries (supplied with 
the product).
•  Place the batteries 
with their terminals 
corresponding to the (
e)
and (
f) indications in the 
battery compartment.
3  Close the battery cover.
CAUTION
Improper use of batteries can result in chemical leakage or explosion. Be sure to follow the instructions below.
•  Do not mix batteries of different types. Different types of batteries have different characteristics.
•  Do not mix old and new batteries. Mixing old and new batteries can shorten the life of new batteries or cause chemical leakage
in old batteries.
•  Remove batteries as soon as they are worn out. Chemicals that leak from batteries that come in contact with skin can cause a 
rash. If you fi nd any chemical leakage, wipe thoroughly with a cloth.
•  The batteries supplied with this product may have a shorter life expectancy due to storage conditions.
•  If you will not be using the remote control unit for an extended period of time, remove batteries from it.
Preparation
Connecting Antenna Cable
•Connect the antenna cable to the TV using one of the methods in the illustration as shown (
1,
2,
3 or 
4).
1  Cable without a CATV 
converter
3 Combination VHF/
UHF antenna
4 Separate VHF/UHF 
antenna 2 VHF/UHF antenna
1. A 75-ohm system is generally a round cable with F-type connector 
that can easily be attached to a terminal without tools.
2. A 300-ohm system is a fl at “twin-lead” cable that can be attached 
to a 75-ohm terminal through a 300/75-ohm adapter.
F-type connector 300-ohm twin-lead cable (fl at)F-type connector
75-ohm coaxial cable (round)
75-ohm coaxial cableNOTICE
When connecting the RF cable to the TV set, do not tighten F-type 
connector with tools.
If tools are used, it may cause damage to your TV set. (The breaking 
of internal circuit, etc.)F-type connector should be fi nger-tightened only.
-$-&6@&JOEC


-$-&6@&JOEC








 
						

							11
Part Names
TV (Front)
Center Icon illumination
(See page 33.)
Remote control sensor
*1 OPC: Optical Picture Control (See page 27.)
*2 This panel emits the infrared signal towards the 3D Glasses you wear when you view 3D images. 
Do not place anything between the 3D infrared emitter on the TV and the infrared receiver on the 3D Glasses.
3D infrared emitter *2
OPC sensor *1
TV (Rear/Side)
RS-232C terminal
Antenna/
Cable in POWER
button
MENU
button
INPUT
button
Channel
buttons
(CH
U/
V)
Volume
buttons
(VOL
k/
l)COMPONENT
terminals
DIGITAL AUDIO 
OUTPUT terminalHDMI 3 terminal
HDMI 4 terminal HDMI 1 terminal
ARC:  Audio Return Channel
  (See pages 57 and 58.)VIDEO 2 terminals
VIDEO 1 terminals
AUDIO OUT terminal
USB 1 terminal
USB 2 
terminal
ETHERNET
terminalHDMI 2 terminal
PC IN terminal
*1 *2
*1
*1
AUDIO IN terminal 
(shared for PC IN 
and HDMI 1) *3
*1 See pages 13 to 17 and 57 for external equipment connection.
*2 See pages 18 and 25 for button operations.
*3 See page 62 for details on the Audio Select function.
-$-&6@&JOEC


-$-&6@&JOEC








 
						

							
12
118
19
20
21
4 3 2
5
23
24
8 7 6
9
25
26
28
29
15 14 13 12 11 10
16
17 27 22
1 POWER:
 Switch the TV power on or enter standby. (See 
page 18.)
2TV ,STB ,DVD•VCR ,AUDIO:  Switches the remote 
control for TV, STB, DVD, BD, VCR and AUDIO operation. 
(See pages 55 to 56 for details.)
  * To enter the code registration mode, you need to press  an appropriate button ( STB,DVD •VCR  or AUDIO ) and 
DISPLAY  at the same time.
3 External equipment operational buttons:  Operate the 
external equipment.
4 OPTION:  Display the Link Operation Menu screen. This 
button will function only when AQUOS LINK is used. (See 
pages 57 to 60 for details.)
5 SLEEP:  Set the sleep timer. (See page 21.)
60 –9:  Set the channel. (See page 21.)
7 • (DOT):  (See pages 21 and 55.)
8 CC:  Display captions from a closed-caption source. (See 
page 23.)
9
AV MODE:  Select an audio or video setting. (See page 22.)
10 MUTE:  Mute the sound. (See page 21.)
11 VOL k/
l :
 Set the volume. (See page 21.)
12 MENU:  Display the menu screen. (See page 25.)
13 3D:  Select between 3D and 2D image viewing. (See 
pages 42 to 43 for details.)
14 a/
b /
c /
d ,
ENTER:  Select a desired item on the screen.
15 EXIT:  Turn off the menu screen.
16 FAVORITE CH:  Set the favorite channels. (See page 35.)
17 A , B , C , D:  Select 4 preset favorite channels in 4 different 
categories. (See page 35.)
  While watching, you can toggle the selected channels by  pressing A,B ,C  and  D.
18 DISPLAY:  Display the channel information.
19 POWER (SOURCE):  Turns the power of the external 
equipment on and off.
20 FREEZE:  Set the still image. Press again to return to 
normal screen. (See page 21.)
21 POWER SAVING:  Select Power Saving settings. (See 
page 22.)
22 ENT:  Jumps to a channel after selecting with the  0–9
buttons.
23 FLASHBACK:  Return to the previous channel or external 
input mode. (See page 21.)
24 VIEW MODE:  Select the screen size. (See pages 24 and 
61.)
25 INPUT:  Select a TV input source. (TV, HDMI1, HDMI2, 
HDMI3, HDMI4, COMPONENT, VIDEO1, VIDEO2, PC IN, 
Home Network (DLNA), USB)  (See pages 13 and 22.)
26 CH U/
V :
 Select the channel. (See page 21.)
27 APPS:  Display the application window. (See page 22.)
28 RETURN:  Return to the previous menu screen.
29 FAV APP 1, 2, 3:  You can assign your favorite 
applications to these buttons. (See page 35.)
Remote Control Unit
•  When using the remote control unit, point it at the TV.
Part Names
-$-&6@&@JOEE


-$-&6@&@JOEE








 
						

							
13
Introduction to Connections
Types of Connection
For connecting the TV to external equipment, use commercially available \
cables.•   The illustrations of the terminals are for explanation purposes and may\
 vary slightly from the actual products.
■ Connecting to video equipment or PC
Image quality differs depending on the terminal used. To enjoy clearer i\
mages, check the output terminals of your 
external equipment and use its appropriate terminals for higher quality \
images.
Pages
14, 16, 17
Terminal
on the TV CableTerminal on external
equipment
Image
Quality
AV cable
Component video cable
Audio cable
HDMI-certified cable
Ø 3.5 mm stereo minijack cable
DVI-HDMI conversion cable
HD
Quality
Standard Quality
AUDIO
DVI OUT
Pages
14, 17
 Page 15
  Page 15
■  Connecting to audio equipment
Cable Terminal on external
equipment
Optical fiber cable
Ø3.5 mm stereo minijack to RCA audio cable
Terminal on the TV
DIGITAL AUDIO INPUTOPTICAL
ANALOG AUDIO IN
 Page 16
  Page 16
1 Press 
INPUT.
•  The INPUT list screen displays.
2 Press  a/
b  to select the input source.
•  You can also select the input source by pressing  INPUT . Each time  INPUT is pressed, the input source 
toggles.
HDMI4TV
HDMI1 HDMI2 HDMI
3
•  An image from the selected source automatically 
displays.
•  If the corresponding input is not plugged in, you  cannot change the input. Be sure to connect the 
equipment beforehand.
INPUT
INPUT
TV
HDMI1
HDMI2
HDMI3
Menu
AIR
Input
Example
Displaying an External Equipment Image
To view external source images, select the input source by pressing  INPUT on the remote control unit or on the TV.
-$-&6@&@JOEE


-$-&6@&@JOEE








 
						

							
14
Connecting to External Equipment
You can connect many types of external equipment to your TV. To view ext\
ernal source images, select the input 
source from INPUT on the remote control unit or on the TV. (See pages 13 and 22.)
For connecting the TV to external equipment, use commercially available \
cables.
CAUTION
• To protect equipment, always turn off the TV before connecting any exter\
nal equipment.
• Please read the relevant operation manual (Blu-ray disc player, etc.) \
carefully before making connections.
Connecting a Blu-ray Disc/DVD Player or HD Cable/Satellite Set-top Box 
■  When using HDMI cable (HDMI 1, 2, 3 or 4):
The HDMI (High Defi nition Multimedia Interface) terminal is an audio-video interface that \
enables a connection for audio and 
video signals using a single cable. The HDMI terminal supports high-reso\
lution video input.
• Blu-ray disc player      • DVD player
• HD cable/satellite set-top box
HDMI OUT
HDMI-certified cable
• To enjoy 1080p display capability, connect your external equipment using\
 an HDMI-certifi ed cable or a component cable 
and set the equipment to 1080p output.
• Supported Audio format: Linear PCM, sampling rate 32/44.1/48kHz.
• When you connect external equipment using a DVI-HDMI conversion cable or\
 when you connect ARC-compatible  equipment, use HDMI 1.
■ When using DVI-HDMI conversion cable (HDMI 1):
•Blu-ray disc player     •DVD player
• HD cable/satellite set-top box
AUDIO DVI OUT
Ø 3.5 mm stereo minijack cable DVI-HDMI conversion cable
• When using a DVI-HDMI conversion cable, you should make an analog audio \
connection. In this case, in addition to 
connecting a DVI-HDMI conversion cable to the HDMI 1 terminal, connect a\
 Ø 3.5 mm stereo minijack cable to the AUDIO 
IN terminal and set "Audio Select" to "HDMI+Analog".  (See page 62.)
-$-&6@&@JOEE


-$-&6@&@JOEE








 
						

							
15
Connecting to External Equipment
■ When using Component cable (COMPONENT):
• Blu-ray disc player      • DVD player
• HD cable/satellite set-top box
COMPONENT OUT
AUDIO-L (White) AUDIO-R (Red)
Y (Green)
P
B (Blue)
P
R (Red) Audio cable
Component video cable
•  To enjoy 1080p display capability, connect your external equipment using\
 an HDMI-certifi ed cable or a component cable and  set the equipment to 1080p output.
•  See page 14 for connecting a Blu-ray disc player, DVD player or an HD ca\
ble/satellite set-top box to the HDMI terminal.
Connecting a VCR, Game Console, Camcorder or Cable/Satellite Set-top Box\
■  When using Composite cable (VIDEO 1 or 2):
• Game console  • VCR
• Camcorder  • Cable/Satellite set-top box
AV cableVIDEO (Yellow)
AUDIO-L (White) AUDIO-R (Red)
-$-&6@&@JOEE


-$-&6@&@JOEE








 
						

							
16
Connecting to External Equipment
Connecting a Surround System/Audio System
■ When connecting an AV amplifi
 er for surround system
DIGITAL AUDIO INPUTOPTICALHDMI IN
HDMI OUT
HDMI OUTHDMI-certified cable *1 HD Cable/Satellite set-top box
Optical fiber cable *2
•  Letting the TV output the audio to an AV amplifi er: *1 When you connect ARC-compatible equipment, use the HDMI 1 terminal.
*2 If the equipment to be connected is not compatible with the ARC, connect\
 an optical fi ber cable.
•  If the image is not in sync with the audio, check the settings of the co\
nnected surround system.
■ When connecting an Audio amplifi
 er
It is possible to output audio through the DIGITAL AUDIO OUTPUT terminal\
. (See page 32 for details.) PCM audio 
outputs from the terminal.
DIGITAL AUDIO INPUTOPTICAL
Optical fiber cable
•  Depending on the connected equipment, audio will not output from the DIG\
ITAL AUDIO OUTPUT terminal in HDMI  connection. In this case, set the audio formats of the connected equipme\
nt to PCM, 32/44.1/48 kHz.
•
Optical digital audio will be output in 2-ch stereo when it is from the \
external equipment connected to the TV using an HDMI ca ble.
ANALOG AUDIO IN
Ø3.5 mm stereo minijack to RCA audio cable
•  See page 32 for details on the Output Select function.
-$-&6@&@JOEE


-$-&6@&@JOEE








 
						

							17
Connecting a PC
Refer to page 62 for a list of PC signals compatible with the TV.
■ When using HDMI cable (HDMI 1, 2, 3 or 4):
HDMI OUT
HDMI-certified cable
•  Depending on the board, only video signals may be output. In this case, in addition to connecting an HDMI-certifi ed cable 
to the HDMI 1 terminal, connect a Ø 3.5 mm stereo minijack cable to the AUDIO IN terminal and set "Audio Select" to 
"HDMI+Analog". (See page 62.)
•
The HDMI terminals only support digital signal.
■ When using DVI-HDMI conversion cable (HDMI 1):
DVI OUT
AUDIO
DVI-HDMI conversion cable
Ø 3.5 mm stereo minijack cable
•  When using a DVI-HDMI conversion cable, you should make an analog audio connection. In this case, in addition to 
connecting a DVI-HDMI conversion cable to the HDMI 1 terminal, connect a Ø 3.5 mm stereo minijack cable to the AUDIO IN 
terminal and set "Audio Select" to "HDMI+Analog". (See page 62.)
■ When using analog RGB cable (PC IN):
Ø 3.5 mm stereo minijack cable
RGB AUDIO
Analog RGB cable
(D-sub 15-pin cable or VGA cable)
•  When using an analog RGB cable, input the audio signal to the AUDIO IN terminal of PC IN.
•  When connecting a PC to the PC IN, set "Audio Select" to "Video+Audio". (See page 62.)
Connecting to External Equipment
-$-&6@&@JOEE


-$-&6@&@JOEE








 
						

							18
Turning On/Off the Power
POWER
POWER(On/Standby)
PressPOWER on the TV or on the remote control unit 
to turn the power on.
•  The Initial Installation starts when the TV powers on for the 
fi rst time. If the TV has been turned on before, the Initial 
Installation will not be invoked. For changing the settings of 
the Initial Installation, perform "EZ setup" on the Initial Setup 
menu on page 34.
PressPOWER on the TV or on the remote control unit 
again to turn the power off.
•  The TV enters standby and the image on the screen 
disappears.
•  If you are not going to use this TV for a long period of time, 
be sure to remove the AC cord from the AC outlet.
•  Weak electric power is still consumed even when the TV is 
turned off.
Watching TV
Initial Installation
When you turn on the TV for the fi rst time, it will 
automatically memorize the broadcasting channels 
available in the region where you live. Perform the 
following steps before you press POWER on the 
remote control unit.
1.Insert the batteries into the remote control unit. (See page 10.)2.  Connect the antenna cable to the TV. (See page 10.)
3.  Plug in the AC cord to the AC outlet. (See page 9.)
Language (Language setting)
Select from among 3 languages: English, French and 
Spanish.
1 Press 
a/
b to select the desired language listed 
on the screen, and then press ENTER.
Language
TV Location
Antenna & Cable/STB
Air/CableEnglish
Español Français
CH SearchCompleted
TV Location
Select "Home" or "Store" for the location where 
you plan to install the TV. This product qualifi es for 
ENERGY STAR in Home mode default setting.
2 Press 
c/
dto select "Home" or "Store".
 Press ENTER to enter the setting.
Select
StoreHome
Home: “Power Saving” is set to "Advanced", and AV 
MODE is set to "STANDARD".
Store: “Power Saving” is set to "Off" and AV MODE is 
set to "DYNAMIC (Fixed)". Picture Reset and Feature 
Demo can be set.
Picture Reset: AV MODE will be set to "DYNAMIC (Fixed)" 
regardless of whether Picture Reset is "On" or "Off".
• If you select "On" and there is no operation for 30 minutes:
-
AV MODE will be reset to "DYNAMIC (Fixed)" and, when a 
3D signal is detected, 3D images will switch to 2D images. 
• When "Off" is selected:
- AV MODE will be set to "DYNAMIC (Fixed)".
Feature Demo: When “On” is selected, after all the settings 
are completed, the Feature Demo screen is displayed if there 
is no operation for several minutes.
•  ENERGY STAR qualifi cation is based on AV MODE 
"STANDARD".
-$-&6@&JOEC


-$-&6@&JOEC