Sharp Lc 52xs1e Operation Manual

Check programme information
Press a/b /c /d  to select the programme you 
want to check.
Press  R.
040
10 : 00AM - 1 : 00 AM BBC News 24
BBC News
Programme Info. Back to EPG The BBC’s rolling news service with headlines every 15 minutes.
10 AM11 0 PM 1 2 3
BBC TWO    002
BBC THREE   007
BBC FOUR    010
BBC FIVE    012
CBBC Channel  030
BBC 1   061
BB22     062
BBC NEWS 24  340
BBCi     351 This is BBC THREE 
BBC NEWS BBC NEWS 
BBC NEWS BBC NEWS 
BBCi BBCi 
This is BBC THREE 
RNextB
Press 
OK to tune to...

Watching TV
Timer recording using EPG
You can record TV programmes using data from the 
EPG.Press  EPG.
Press  a/b /c /d  to select the programme you 
want to record, and then press  OK.
Press  c/d  to select the preferred timer setting, 
and then press  OK.
Watch Record No
If you select “No”, the TV returns to the EPG screen.
Watching a programme at a set time
Press c/d  to select “Watch”, and then press 
OK .
Press  c/d  to select “Yes”, and then press  OK.
The selected TV programme is marked with an...

Buttons for teletext operations
Buttons Description
P r /s Increase or decrease the page number.
Colour (R/G/
Y/B) Select a group or block of pages 
displayed in the coloured brackets at the 
bottom of the screen by pressing the 
corresponding 
Colour (R/G/Y/B)  on the 
remote control unit.
0–9 Directly select any page from 100 to 899 
by using the 0–9  numeric buttons.
v  (Top/
Bottom/Full) Switch the teletext image to Top, Bottom 
or Full.
k  (Reveal 
hidden 
Teletext) Reveal or hide hidden...

Connecting external devices
Before connecting ...
Be sure to turn off the TV and any devices before making any connections.
Firmly connect a cable to a terminal or terminals.
Carefully read the operation manual of each external device for possible connection types. This also helps you get the be\
st 
possible audiovisual quality to maximise the potential of the TV and the\
 connected device.
Refer to page 46 for connecting a PC to the AVC System.
Introduction to connections
The AVC System is equipped...

Connecting external devices
HDMI connection
The HDMI connections permit digital video and audio 
transmission via a connection cable from a player/
recorder. The digital picture and sound data are 
transmitted without data compression and therefore 
lose none of their quality. Analogue/digital conversion 
is no longer necessary in the connected devices, 
which also would result in quality losses.
DVI/HDMI conversion
Using a DVI/HDMI cable, the digital video signals of 
a DVD can also be played via the...

Connecting external devices
NOTEIn cases when the decoder needs to receive a signal from the TV, make sure to select the appropriate input terminal to which 
the decoder is connected in “Manual Adjust” in the “Analogue Se\
tting” menu (Page 36).
TV-VCR advanced AV Link systems may not be compatible with some external sources.
You cannot connect the VCR with decoder using a fully wired SCART cable when selecting “Y/C” under “EXT2” in the “Input 
Select” menu.
Controlling devices with SCART using AV Link...

Connecting external devices
DIGITAL AUDIO  INAUX1 INL
RAUX OUT L
R
Connecting an amplifier with analogue 
audio inputEConnecting an amplifier with digital audio 
inputE
Speaker/amplifier connection
Connect an amplifier with external speakers as shown below.
After connecting
Digital audio output setting
After connecting an amplifier with digital audio 
input and external speakers as shown, you should 
set an audio output format compatible with 
the programme you are watching or the device 
connected.
Go...

Connecting external devices
Inserting a CA Card
In order to receive coded digital stations, a Common 
Interface Module (CI Module) and a CA Card must be 
inserted in the CI slot of the AVC System (See below).
The CI Module and the CA Card are not supplied 
accessories. They are usually available from your 
dealers.
Inserting the CA Card into the CI Module
With the side with the gold coloured contact 
chip facing the side of the CI Module marked 
with the provider’s logo, push the CA Card 
into the CI...

AQUOS LINK
Controlling HDMI devices using AQUOS LINK
What is AQUOS LINK?
Using the HDMI CEC protocol, with AQUOS LINK you can interactively operate 
compatible system devices (AV amplifier, DVD player/recorder, Blu-ray player/recorder) 
using a single remote control unit.
NOTE
AQUOS LINK-compatible AQUOS AUDIO speaker system and AQUOS Recorder are scheduled 
to be on sale after the release of this TV (as of October 2008).
What you can do with AQUOS LINK
One Touch Recording (DTV/SAT only)
You do not have...

AQUOS LINK
AQUOS LINK Control
Set to “On” to enable AQUOS LINK functions.Press  MENU  and the “MENU” screen displays.
Press  c/d  to select “Option”.
Press  a/b  to select “AQUOS LINK Setup”, and 
then press  OK.
Press  a/b  to select “AQUOS LINK Control”, 
and then press  OK.
Press  c/d  to select “On”, and then press  OK.
Auto Power On
If this is activated, the One Touch Play function 
is enabled. While the TV is in standby mode, it 
automatically turns on and plays back the image from 
the HDMI...