Sharp Lc 52xs1e Operation Manual

1 3 2  4 5 
Supplying power to the antenna
You must supply power to the antenna in order to receive digital terrestrial broadcasts or satellite broadcasts 
after running the initial auto installation. Go to “MENU” > “Se\
tup” > “Antenna Setup-DIGITAL” > “Digital Setup” 
> “Supply Voltage” > select “On”.
Quick guide
Setting the TV and antenna cables
Insert the fixture for 
the HDMI cable into 
the hole below the 
DISPLAY OUTPUT 
terminal on the AVC 
System.
1Detach the parts 
of the fixture 
while...

Turning on and running the initial auto installation
Plugging the AC cord to the AC outlet
AC cord*
AC cord*
Place the TV close to the AC 
outlet, and keep the power 
plug within reach.
Product shape varies in some countries.
*
Power on and run the auto installation
Turn on the main power using 
a  on the Display.
Run the initial auto installation 
(Pages 11–15).
Language setting
English
Italiano
Svenska
Home/Store setting
STORE
HOME
Country setting
Austria A  B/G
Finland FIN B/G
Greece GR B/G
Channel...

Quick guide
Initial auto installation
When the TV is powered on for the first time after 
purchase, the initial auto installation wizard appears. 
Follow the menus and make the necessary settings 
one after another.Press  a on the Display.
The initial auto installation wizard appears.
Setting the OSD language.
English
Italiano
Svenska
Press  a/b /c /d  to select the desired language, 
and then press  OK.
Selecting the location of the TV.
STORE
HOME
Press  c/d  to select where you will use this TV, 
and...

Quick guide
“Cable” searching
The current DVB-C settings are displayed on the 
screen.
Change Setting
Start Search Scrambled stations:
Search method: 
No
Channel
Start frequency:  47.0 MHz
Network ID: 
Symbol rate 1:  None
6875
Symbol rate 2:  6900
QAM modulation 1: 
QAM modulation 2:  64
None
no
When you start searching for DVB-C channels 
with the current setting:
Press  c/d  to select “Start Search”, and 
then press  OK.
01 628.2502 693.2503 767.2504 831.25
The TV searches for, sorts and stores all...

Set up “Symbol rate 2” if the cable provider uses several 
symbol rates.
*
Menu Description Selectable Item
Scrambled 
Stations Specifies if you 
need to add pay-TV 
services.
Yes, No
Search 
Method Specifies how you 
search channels. Channel: Extracts 
all of information 
from a channel 
(quick, but needs 
corresponding TV 
stations).
Frequency: 
Checks every 
frequency in range 
(slow).
Start 
frequency ————————— 47.0–858.0 MHz
Network ID
Specifies the network. 
Set this to register only 
the...

Quick guide
“Satellite Search” setting
Press c/d  to select “Yes”, and the then press 
OK .
No
Ye s
If you do not perform “Satellite Search” setting, select “No”, 
and then press  OK.
The current DVB-S setting screen is displayed.
Change Setting 
Next  Satellite System
Max. 4 satellites on DiSEqC multiswitch
LNB Frequency
Satellite
ASTRA1
SAT1 Low
9700
High
10700
no
You must first complete “Change Setting” before moving to 
the “Next” setting.
When starting the satellite search after setting 
the...

Quick guide
When you change the antenna connection 
setting:
Press c/d  to select “Change Setting” on the DVB-S 
setting screen in the left column, and then press  OK.
The antenna connection setting screen is displayed.
Single satellite
2 satellites on 22kHz switchbox
2 satellites on toneburst switchbox
Max. 4 satellites on DiSEqC multiswitch
Communal satellite system
NOTEYou can select the antenna connection method from the five types. 
Consult your dealers before using a method other than “Single...

Checking signal strength and 
channel strength (DVB-T/C)
If you install a DVB-T/C antenna for the first time or 
relocate it, you should adjust the alignment of the 
antenna to receive a good reception while checking 
the antenna setup screen.Press  MENU  and the “MENU” screen displays.
Press  c/d  to select “Setup”.
Press  a/b  to select “Antenna Setup-DIGITAL”, 
and then press  OK.
Press  a/b  to select “Digital Setup”, and then 
press  OK.
Checking signal strength
Press  a/b  to select “Signal...

Watching TV
Selecting a sound mode
DTV/SAT mode:
If multi sound modes are received, each time you press 2 
the mode switches as follows.
Audio (ENG) : STEREO
L/R LRLR
Audio (ENG) : CH A
CH A CH B CH AB
Audio (ENG) : MONO
Press c/d  to select L or R sound when the STEREO or 
DUAL MONO screen is displayed.
Audio (ENG) : STEREO
L/R LRLR
NOTEThe sound mode screen disappears in six seconds.
Selectable items vary depending on the received broadcasts.
ATV mode:
Each time you press  2, the mode switches as...

Watching TV
Useful functionsE
Common Operation
Press MENU  and the “MENU” screen displays.
Press  c/d  to select “Digital Setup”.
Press  a/b  to select “EPG Setup”, and then 
press  OK.
Digital Setup 
REC Picture Size
Download Setup
EPG Setup
Subtitle
CI Select
CI Menu [Yes]
[16:9 TV]
Press 
a/b  to select the desired item, and then 
press  OK (Example: “EPG Setup”, “Display 
Range Setup”, etc.).
Ye s No
EPG Setup
Display Range Setup
Genre Icon Setup
Press 
a/b /c /d  to select or adjust the desired...