Sharp Lc 40le810 Operation Manual

							
RS-232C command list
CONTROL ITEM COMMAND PARAMETER CONTROL CONTENTS
POWER 
SETTINGP O W R 0 _ _ _ POWER OFF (STANDBY)
INPUT 
SELECTION A I T G D _ _ _ _ INPUT SWITCHING 
(TOGGLE)
I T V D _ _ _ _ TV (CHANNEL FIXED)
I D T V _ _ _ _ DTV (CHANNEL FIXED)
I A V D * _ _ _ EXT 1_3 (1_3), HDMI 
1_4 (4_7)
CHANNEL D C C H * * _ _ TV DIRECT CHANNEL  (1_99)
C H U P _ _ _ _ CHANNEL UP
C H D W _ _ _ _ CHANNEL DOWN D T V D * * * _ THREE DIGIT DIRECT  CHANNEL (1_999) (Non-
Nordic countries)
D T V D * * * * FOUR DIGIT DIRECT  CHANNEL (1_9999) 
(Nordic countries only)
D T U P _ _ _ _ DTV CHANNEL UP
D T D W _ _ _ _ DTV CHANNEL DOWN
INPUT 
SELECTION B I N P 1 0 _ _ _ EXT 1 (Y/C)
I N P 1 1 _ _ _ EXT 1 (CVBS)
I N P 1 2 _ _ _ EXT 1 (RGB)
I N P 3 0 _ _ _ EXT 3 (COMP)
I N P 3 1 _ _ _ EXT 3 (RGB)
AV MODE 
SELECTION A V M D 0 _ _ _ TOGGLE
A V M D 1 _ _ _ STANDARD
A V M D 2 _ _ _ MOVIE
A V M D 3 _ _ _ GAME
A V M D 4 _ _ _ USER
A V M D 5 _ _ _ DYNAMIC (Fixed)
A V M D 6 _ _ _ DYNAMIC
A V M D 7 _ _ _ PC
A V M D 8 _ _ _ x.v.Colour
A V M D 1 0 0 _ AUTO
A V M D ? ? ? ?
1_8, 100
VOLUME V O L M * * _ _ VOLUME (0_60)
CONTROL ITEM COMMAND PARAMETER CONTROL CONTENTS
POSITION H P O S * * * _ H-POSITION (AV/PC)
V P O S * * * _ V-POSITION (AV/PC)
C L C K * * * _
CLOCK (0_180)
P H S E * * _ _ PHASE (0_40)
WIDE MODE W I D E 0 _ _ _ TOGGLE (AV) W I D E 1 _ _ _ NORMAL (AV)
W I D E 2 _ _ _ ZOOM 14:9 (AV)
W I D E 3 _ _ _ PANORAMA (AV)
W I D E 4 _ _ _ FULL (AV)
W I D E 5 _ _ _ CINEMA 16:9 (AV)
W I D E 6 _ _ _ CINEMA 14:9 (AV)
W I D E 7 _ _ _ NORMAL (PC)
W I D E 8 _ _ _ CINEMA (PC)
W I D E 9 _ _ _ FULL (PC)
W I D E 1 0 _ _ DOT by DOT (AV/PC)
W I D E 1 1 _ _ UNDERSCAN (AV)
W I D E 1 2 _ _ AUTO (USB-Video)*
W I D E 1 3 _ _ ORIGINAL (USB-Video)*
MUTE M U T E 0 _ _ _ TOGGLE
M U T E 1 _ _ _ MUTE
M U T E 2 _ _ _ MUTE OFF
SURROUND A C S U 0 _ _ _ SURROUND TOGGLE A C S U 1 _ _ _ SURROUND ON
A C S U 2 _ _ _ SURROUND OFF
AUDIO 
CHANGE A C H A _ _ _ _ TOGGLE
SLEEP TIMER O F T M 0 _ _ _ OFF O F T M 1 _ _ _ SLEEP TIMER 30 MIN
O F T M 2 _ _ _ SLEEP TIMER 1 HOUR
O F T M 3 _ _ _ SLEEP TIMER 1 HOUR  30 MIN
O F T M 4 _ _ _ SLEEP TIMER 2 HOUR
O F T M 5 _ _ _ SLEEP TIMER 2 HOUR  30 MIN
TEXT T E X T 0 _ _ _ TEXT OFF
T E X T 1 _ _ _ TEXT ON (TOGGLE)
D C P G * * * _
DIRECT PAGE JUMP 
(100_899)
These commands are available only for during running USB 
video mode.
*
Connecting a PC
 
						

							0
Troubleshooting
ProblemPossible solutionNo power.
•
Turn on (;) the MAIN POWER switch on the rear of the TV (Page 4).
Is the AC cord disconnected?
Check if you pressed  “Setup”.
Press a/b to select “Auto installation”, “Programme setup”, “PIN” or “Reset”, and then press 
;. 
The PIN input window will display.
Press and hold both :r and i+ on the TV simultaneously until the message appears on the 
screen.
ResetIf complex adjustments are made so that the settings cannot be restored to normal, you can reset the settings to the 
factory preset values.
Go to “Menu” > “Setup” > “View setting” > “Reset”.
Press c/d to select “Yes”, and then press ;.
“Now, TV will restart automatically, OK?” displays on the screen.
Press c/d to select “Yes”, and then press ;.“Now initialising...” displays on the screen and blinks.
After the reset has completed, the power shuts off and then comes back on. The screen will have returned to its original settings.
NOTEPIN input is required when executing “Reset”. The default PIN is “1234”. To change the PIN setting, refer to  Password/Lock settings 
(Page 33). To clear the PIN setting (PIN input will no longer be needed), refer to CLEARING THE PIN (Page 50).
1
2
3
1
2
•
3•
•
•
Appendix
 
						

							
Updating your TV via DVB-T
Ensure that your TV software version is always up to 
date. From time to time SHARP will make updated TV 
base software and DVB software available.
View setting
Download setup
Go to “Menu” > “Setup” > “View setting” > “Individual setting” > “Standby search” > 
“Download setup”.
Searching for updates*
All countries except UK, Sweden and Italy are set to “No” for 
this function.
The TV automatically determines whether a new software 
version is available when the TV is in standby mode.
Item
Yes Automatically searches for new software 
updates available when the TV is in 
standby mode.
No Does not search for update information.
Now Checks if there is new software 
immediately.
Downloading the software
You can select the method of update.
If the software is updated, the confirmation 
message “New download information has 
been detected.” appears.
If the TV receives the update service while in standby 
mode, a confirmation message displays after turning on 
the power.
Follow the screen prompts.
Item
Yes Starts downloading immediately. It takes 
approximately one hour to update. You 
cannot carry out other operations while 
downloading.
Cancels the download by pressing 
; on the remote control unit when 
“Discontinue” is displayed on the screen 
during the update.
•
No
Starts downloading automatically several 
minutes after entering standby mode.
NOTEThe TV must remain in standby mode for download. Do not 
turn off the power using >a on the TV.
Updating the software may take some time.
*
1
•
2
•
•
Getting update information
Information
Message list
When new software is detected, you can confirm the update information and download the software from 
“Message list”.
Go to “Menu” > “Setup” > “Information” > 
“Message list”.
NOTEWhen the TV succeeds at downloading new software, the 
message is updated in the “Message list” of the “Information”\
 
menu.
The software update will not be carried out if there is no new 
software available at the specified download time.
Information
Receiver report
Display reports regarding failures and changes for timer settings.
Go to “Menu” > “Setup” > “Information” > 
“Receiver report”.
Information
Identification
You can check the TV ID on the screen for reporting to customer service.
Go to “Menu” > “Setup” > “Information” > 
“Identification”.
•
•
Appendix
 
						

							
Appendix
Updating your TV via USB
Information
Software update
This function allows you to update to the latest software using a USB device. You must update the software 
through the USB terminal.
To check the software version for the TV, use the URL shown 
on the back cover.
Go to “Menu” > “Setup” > “Information” > 
“Software update”.
Press ; and then insert the USB device 
containing the software update file.
CAUTIONBe sure to insert the USB device correctly into the terminal.
•
1
2
•
The TV displays a confirmation screen while 
checking the data in the inserted USB device.
CAUTIONIf the data is not compatible with the system, an error message 
appears on the screen. Repeat steps 2 and 3 after pressing 
;.
When an error message displays, check to see if:
The USB device is inserted firmly.
The USB memory has two or more software update files.
No data for updating the system exists in the USB 
memory.
The software update file is broken.
The software update file is not compatible with your TV’s 
software.
The current system is same as the system update data.
The TV displays the software version 
information after checking the data.
Press c/d to select “Yes” to update the 
system, and then press ;.
Press ; to automatically reset and start the 
update operation.
This operation may take a while.
The TV starts updating the system
A confirmation message appears on the 
screen after completing the update and 
then automatically restarts the TV. Press 
; to complete the operation.
3
•
••
•
•
•
•
•
4
5
6
•
 
						

							
Appendix
Information on the software license for this product
Software compositionThe software included in this product is comprised of various software components whose individual copyrights are held by SHARP or by 
third parties.
Software developed by SHARP and open source software The copyrights for the software components and various relevant documents included with this product that were developed or written 
by SHARP are owned by SHARP and are protected by the Copyright Act, international treaties, and other relevant laws. This product also 
makes use of freely distributed software and software components whose copyrights are held by third parties. These include software 
components covered by a GNU General Public License (hereafter GPL), a GNU Lesser General Public License (hereafter LGPL) or other 
license agreement.
Obtaining source code Some of the open source software licensors require the distributor to provide the source code with the executable software components. 
GPL and LGPL include similar requirements. For information on obtaining the source code for the open source software and for obtaining 
the GPL, LGPL, and other license agreement information, visit the following website:
http://www.sharp-eu.com/gpl/
We are unable to answer any questions about the source code for the open source software. The source code for the software 
components whose copyrights are held by SHARP is not distributed.
Acknowledgements The following open source software components are included in this product:
• linux kernel • busy box • glibc • zlib • libpng • libjpeg • mtd\
-utils • u-Boot
Software copyrights
BSD License This product includes software developed by the University of California, Berkeley and 
its contributors.
libjpeg This software is copyright © 1991-1998, Thomas G. Lane. Portions of this software are 
based in part on the work of the Independent JPEG Group.
Portions copyright © 2004 Intel Corporation
Warning regarding basic use
Cautions regarding use in high and low temperature environmentsWhen the TV is used in a low temperature space (e.g., room, office), the picture may leave trails or appear slightly delayed. This is not 
a malfunction, and the TV will recover when the temperature returns to normal.
Do not leave the TV in a hot or cold location. Also, do not leave the TV\
 in a location exposed to direct sunlight or near a heater, as this 
may cause the cabinet to deform and the LCD panel to malfunction.
Storage temperature: e 5 °C to e 35 °C.
•
•
Devices connected to the protective earthing of the building installation through the MAINS connection or through other devices with a 
connection to protective earthing and to a television distribution system using coaxial \
cable, may in some circumstances create a fire 
hazard. Connection to a television distribution system therefore has to be provided through a device providing electrical isolation within a 
certain frequency range (galvanic isolator, see EN 60728-11).
NOTEFor requirements in Norway and Sweden, the requirements for isolation are also relevant for devices that can be connected to 
television distribution systems.
•
 
						

							
Specifications
ItemLCD COLOUR TV 
(40 o/81.28 cm), 
LC-40LE820E, LC-
40LE810ELCD COLOUR TV 
(46 o/116.84 cm), 
LC-46LE820E, LC-
46LE810ELCD COLOUR TV 
(52 o/132.08 cm), LC-
52LE820E
LCD panel Advanced Super View 
& BLACK TFT LCD (40 
o/81.28 cm)Advanced Super View 
& BLACK TFT LCD (46 
o/116.84 cm)Advanced Super View 
& BLACK TFT LCD (52 
o/132.08 cm)
Resolution 1,920 x 1,080 x 4 pixels
Video colour system PAL/SECAM/NTSC 3.58/NTSC 4.43/PAL 60
TV function TV-standard AnalogueCCIR (B/G, I, D/K, L/L’)
Digital DVB-T (2K/8K OFDM), DVB-C
Receiving 
channel VHF/UHF
IR A ch_E69 ch (Digital), E2_E69 ch, F2_F10 ch, I21_I69 ch, IR A_IR J ch
CATV Hyper-band, S1_S41 ch
TV-tuning system Auto Preset 999 ch (non-Nordic [DTV]), Auto Preset 9999 ch (Nordic [DTV]), 
Auto Preset 99 ch (ATV), Auto Label, Auto Sort
STEREO/BILINGUAL NICAM/A2
Audio amplifier 10 W x 2/15 W x 1
Speaker (234 mm x 22 mm) x 2/Ø 110 mm
Terminals Antenna
UHF/VHF 75 q Din type (analogue & digital)
RS-232C D-Sub 9 pin male connector
EXT 1 SCART (AV input, Y/C input, RGB input, TV output)
EXT 2 RCA pin (AV input/AUDIO L/R)
EXT 3 15 pin mini D-sub
HDMI 1 (EXT 4) HDMI (ARC)
HDMI 2 (EXT 5) HDMI
HDMI 3 (EXT 6) HDMI
HDMI 4 (EXT 7) HDMI
USB USB
ETHERNET (10/100) Home network connector (only the 820 model series)
HDMI 2/EXT 3 AUDIO (L/R) Ø 3.5 mm jack*
1
DIGITAL AUDIO OUTPUTOptical S/PDIF digital audio output
C. I. (Common Interface) EN50221, R206001, CI Plus specification
OUTPUT/Headphones RCA pin (AUDIO R/L)/Ø 3.5 mm jack (audio output)
OSD language Czech, Danish, Dutch, English, Estonian, Finnish, French, German, Greek, 
Hungarian, Italian, Latvian, Lithuanian, Norwegian, Polish, Portuguese, \
Russian, 
Slovak, Slovene, Spanish, Swedish, Turkish, Ukrainian
Power requirement AC 220_240 V, 50 Hz
Power consumption (method 
IEC62087) 820 models
127 W (0.2 W standby*
2)147 W (0.2 W standby*2)159 W (0.2 W standby*2)
810 models 127 W (0.2 W standby*2)147 W (0.2 W standby*2)
Weight 820 models19.5 kg (without stand), 
23.5 kg (with stand) 24.5 kg (without stand), 
30.0 kg (with stand)30.0 kg (without stand), 
35.0 kg (with stand)
810 models 16.0 kg (without stand), 
19.5 kg (with stand) 20.5 kg (without stand), 
26.0 kg (with stand)
Operating temperature 0 °C to e 40 °C
The HDMI 2 and EXT 3 terminals can both use the same audio input termina\
l.
Standby power consumption applies when the TV is set to not receive EPG data.
As a part of our policy of continuous improvement, SHARP reserves the right to make design and specification changes for product 
improvement without prior notice. The performance specification figures indicated are nominal values of production units. There may be 
some deviations from these values in individual units.
I
J
•
Appendix
 
						

							
Environmental specifications
Item40 inch models46 inch models52 inch models
I On-Mode (W) (HOME MODE)
71 W85 W96 W
J Energy-Save-Mode (W)
Advanced69 W77 W86 W
K Standby-Mode (W)
0.20 W0.20 W0.20 W
L Off Mode (W) MAIN POWER 
switch0.01 W or less
0.01 W or less0.01 W or less
M Annual Energy Consumption (kWh)
103.7 kWh124.1 kWh140.2 kWh
N Annual Energy Consumptioning 
Energy-Save-Mode (kWh)
Advanced
100.7 kWh112.4 kWh125.6 kWh
Measured according to IEC 62087 Ed. 2
For further information about the Energy Save function, please see related pages in this operation manual
Measured according to IEC 62301 Ed. 1
Measured according to IEC 62301 Ed. 1
Annual energy consumption is calculated on the basis of the On-Mode (HO\
ME MODE) power consumption, watching TV 4 hours a day, 
365 days a year
Annual energy consumption is calculated on the basis of the Energy-Save-\
Mode power consumption, watching TV 4 hours a day, 365 
days a year
NOTEThe power consumption of On-Mode varies depending on the images the TV d\
isplays.
Mounting the TV on a wall
This TV should be mounted on a wall only with the wall mount bracket and\
 attachment* available from SHARP (Page 55). 
The use of other wall mount brackets may result in an unstable installation and may cause serious injuries.
Mounting the LCD colour TV requires special skills and should only be performed by qualified service pers\
onnel. Customers 
should not attempt to do the work themselves. SHARP bears no responsibility for improper mounting or mounting that 
results in accident or injury.
You can ask qualified service personnel about using an optional bracket a\
nd attachment* to mount the TV to a wall.
When you mount the TV on a wall, you should attach the supporting post.
Detach the AC cord holder on the rear of the TV before mounting the TV on a wall.
Only for 40 inch models.
Wall mount audio setupWhen you mount the TV on a wall, you can adjust the sound to a more suitable one by setting this function to “Yes”.
Go to “Menu” > “Setup” > “View setting” > “Wall mount audio setup”.
Optional accessoriesThe listed optional accessories are available for this LCD colour TV. Please purchase them at your nearest shop.Additional optional accessories may be available in the near future. When purchasing, please read the newest catalogue for compatibility 
and check the availability.
No. Part name Part number Notes
1 Wall mount bracket (40 inch models) AN-37AG2
The centre of the TV screen is 7.6 mm below the mark “A” on 
the wall bracket.
2 Attachment (40 inch models) AN-37P30
3 Wall mount bracket (46 inch models) AN-52AG4The centre of the TV screen is 13 mm below the mark “b” on 
the wall bracket.
4 Wall mount bracket (52 inch models) AN-52AG4The centre of the TV screen is 1 mm above the mark “b” on 
the wall bracket.
I
J
K
L
M
N
•
•
•
•
•
•
*
E
E
•
Appendix
 
						

							
Rating table for child lock
User-adjusted ratingBroadcasted rating
AGE
4 5678910 1112131415161718
Universal viewing 4—
—————————————
Parental approval  pref. 4
4444—
—————————
X-rated 444444444444444
User-adjusted rating Broadcasted rating
Universal viewing Parental approval pref. X-rated
Universal viewing ———
Parental approval  pref. 4
—
—
X-rated 4 4—
Abbreviation list
Abbreviated term
Stands for
ARC Audio Return Channel
ATV Analogue TV
CEC Consumer Electronics Control
DivX® Digital Video Express
: Digital Noise Reduction
DTV Digital TV
DVB-C Digital Video Broadcasting-Cable
DVB-T Digital Video Broadcasting-Terrestrial
DVI Digital Visual Interface
EPG Electronic Pogramme Guide
HDCP High-bandwidth Digital Content Protection
HDMI High-Definition Multimedia Interface
MHEG Multimedia and Hypermedia Expert Group
OSD On Screen Display
PCM Pulse Code Modulation
USB Universal Serial Bus
WSS Wide Screen Signalling
Appendix
 
						

							
Appendix
Dimensional drawings
LC-52LE820E
LC-46LE820E
LC-40LE820E
(1127.0 )
/ [
993.0 ]
( 1127,0 )
/ [
993,0 ]
(540.0 )
( 540,0 )
[ 450.0 ]
[ 450,0 ]
(
785.0 )
/ [
707.0 ]
( 785,0 )
/ [
707,0 ]
(
400.0 )
/ [
300.0 ]
( 400,0 )
/ [
300,0 ]
(734.0 )
/ [
659.0 ]
( 734,0 )
/ [
659,0 ]
[ 404.0 ]
[ 404,0 ]
(
444.0 )
( 444,0 )
[
48.0 ]
[ 48,0 ]
(
51.0 )
( 51,0 )
[ 132.0 ]
[ 132,0 ]
(
211.0 )
( 211,0 )
39.039,0 [
124.6 ]
[ 124,6 ]
(
157.7 )
( 157,7 )
[ 275.0 ]
[ 275,0 ]
(
340.0 )
( 340,0 )
[
300.0 ]
[ 300,0 ]
(
400.0 )
( 400,0 )
[
503.2 ]
[ 503,2 ]
(
577.6 )
( 577,6 )
400.0
400,0
400.0
400,0
172.0
1260.0
811.0861.0
861,0
50.0
172,0 811,0
50,0
1157.0 1260,0
1157,0
653.0484.0 653,0
484,0540.0
340.0
340,0
39.0
157.7
540,0
39,0 157,7
(
1023.4 )
/ [
890.6 ]
( 1023,4 )
/ [
890,6 ]
(      )
:
 LC-46LE820E
[     ]  :
 LC-40LE820E
 :  LC-46LE820E
 :  LC-40LE820E
NOTEDimensions do not include protrusions such as screws and some parts.
•
 
						

							
Appendix
(1125.0 )
/ [
992.0 ]
( 1125,0 )
/ [
992,0 ]
(540.0 )
( 540,0 )
[ 450.0 ]
[ 450,0 ]
(
784.0 )
/ [
706.0 ]
( 784,0 )
/ [
706,0 ]
(
400.0 )
/ [
300.0 ]
( 400,0 )
/ [
300,0 ]
(733.0 )
/ [
658.0 ]
( 733,0 )
/ [
658,0 ]
[ 404.0 ]
[ 404,0 ]
(
444.0 )
( 444,0 )
[
48.0 ]
[ 48,0 ]
(
51.0 )
( 51,0 )
[ 132.0 ]
[ 132,0 ]
(
211.0 )
( 211,0 )
39.539,5 [
124.0 ]
[ 124,0 ]
(
157.1 )
( 157,1 )
[ 275.0 ]
[ 275,0 ]
(
340.0 )
( 340,0 )
[
300.0 ]
[ 300,0 ]
(
400.0 )
( 400,0 )
[
500.4 ]
[ 500,4 ]
(
575.4 )
( 575,4 )
(
1020.8 )
/ [
887.8 ]
( 1020,8 )
/ [
887,8 ]
LC-46LE810E
LC-40LE810E(      )
:
 LC-46LE810E
[     ]  :
 LC-40LE810E
 :  LC-46LE810E
 :  LC-40LE810E
NOTEDimensions do not include protrusions such as screws and some parts.
•