Sharp Fus51aw Manual

							ENGLISH
AUTO
E-9
ION SHOWER Mode Button
Plasmacluster Ion Mode Selection Button
The Plasmacluster Ion mode can be switched.
The generation of ions will stop and the Plasmacluster Indicator Light
will go out.
LIGHTS ON/OFF Button
Switches the Plasmacluster Indicator Light and CLEAN-SIGN Light ei-
ther ON or OFF. (Please press the Plasmacluster Ion Mode Selection Button for 3 seconds.)
CLEAN
The unit will constantly operate in the Clean Mode, in which the same
numbers of positive and negative ions are discharged. The
Plasmacluster Indicator Light is blue.
When pushing the ION SHOWER Mode button, the ION SHOWER
operation will be activated. (Direct start is available even when the unit is
not turned on.)
The concentrated Plasmacluster Ions (ION SHOWER) will be generated
in the room like a shower for 15 minutes, repeating the airflow cycles
between strong and gentle. (The Plasmacluster Indicator Light  repeats
its colour cycles between blue and green.), and effectively controls the
airborne dust, pollen, mold, and allergen.
•When  the operation finishes, the unit will return to the prior operation.
•When pushing the ION SHOWER button while the ION SHOWER
operation mode is working, the unit will return to the prior operation.
Plasmacluster Indicator Light
CLEAN - SIGN Light
ION SHOWER Mode Button
POWER ON/OFF Button
*Ion Control Mode
Negative ions will be
released in an
increased rate and
controls the ion
balance.
The unit will switch between Clean Mode and the Ion Control Mode*
automatically depending on the amount of impurities in the air as
detected by the dust and odour sensors. Clean Mode will operate for
10 minutes when the Auto function is selected.
OFF 
						

							E-10
CARE AND MAINTENANCE
To prevent dirt or stains on the main unit, clean as often as necessary. If stains are allowed to
remain, they may become hard to clean.
Wipe with a dry, soft cloth
For stubborn stains or dirt, use a soft cloth dampened with warm water.
Do not use volatile fluids
Benzene, paint thinner, polishing powder, etc., may damage the surface.
Do not use detergents
Detergent ingredients may damage the unit.
Keep the unit away from water
MAIN UNIT
FILTER
Washable Active Carbon Filter
SENSORS (DUST SENSOR, ODOUR SENSOR)
Sensor Cover
Hole of Odour Sensor
Clean the top surface of the Washable Active
Carbon Filter lightly with a vacuum cleaner.
Remove dust from the surface of the hole of the
sensors using a vacuum cleaner.
SENSOR FILTER CARE
(The sensor Filter is in the sensor cover.)
Detach the sensor filter and tap it lightly with your
hand to remove the dust.
If it is very dirty, wash it with water and then allow
it to dry thoroughly.
Sensor Cover
Care Cycle
1 month
Care Cycle
2 months
Care Cycle
2 months
Sensor Filter
It does not have a front and
a back.
To maintain optimum performance of this air purifier, please clean the unit including the sensor
and filters periodically.
When cleaning the unit, be sure to unplug the power cord, and never handle the plug with wet
hands. Electrical shock and/or bodily injury may occur as a result. 
						

							ENGLISH
E-11
WASHABLE ACTIVE CARBON FILTER CARE
HAND WASH ONLY!
DO NOT TUMBLE DRY!
Fill a large container with
lukewarm water, add a mild
kitchen detergent
and stir.
1
2
34
5
6
Care Cycle
2 months
Washable Active
Carbon Filter
Dilute as indicated
on the detergent
container.
Allow the filter to soak approxi-
mately 10 minutes before wash-
ing.
If the filter surface is
very dirty, scrub with
an old toothbrush.
Rinse thoroughly with clean
water.
If rinsing in a container,
be sure to rinse 3 to 4
times so that the odour
is rinsed thoroughly from
the filter.
Remove excess water.
CAUTION
The filter will be saturated with water
after rinsing. To decrease drying time,
wrap the filter in an old thick towel so
that excess water can be removed.
CAUTION
Some carbon may adhere to the towel, but it
is harmless.
Dry the filter outdoors if possi-
ble in a well ventilated area.
CAUTION
•The wet filter is heavy. Fix it securely for
drying to make sure it does not fall down.
•The filter takes longer time to dry in win-
ter, on rainy days. Wash it on a day when
the weather is good and dry it in the sun.
Move it indoors at night to prevent freez-
ing.
•Dry the filter outdoors in a well ventilated
area. If dried indoors, the water dripping
off the filter may soil your floor.
•Make sure that the activated carbon has
not shifted to one side of  the filter. If it has,
distribute it evenly with your fingers.
•Let the filter dry thoroughly.
If used while the filter is still moist, then
the air that is exhausted from the main unit
will have an odour. It may take 1 or 2 days
to dry.
Reinstalling the Filters.
Reinstall the filters as shown on Page
E-6,7 
						

							E-12
CARE AND MAINTENANCE
FILTER REPLACEMENT GUIDELINES
The replacement period differs depending on the room environment, the usage hours
and location of the Air Purifier.
If dust or odours persists, replace the filters.
(Refer to “Please read before operating your new Air Purifier”)
HEPA Filter / Washable Active Carbon Filter
Guide for filter replacement timing
•Filter life can be greatly reduced in poor environment.
The presence of cigarette smoke, pet dander and other concentrations of airborne particles
   will cause filters to become clogged in less time. Please check filters regularly and replace
   as needed.
Up to 5 years after opening
Replacement FiltersModel       • HEPA Filter : 1 unit
FZ-S51SEF    • Washable Active Carbon Filter : 1 unit
REPLACING THE FILTERS1. See page E-6,7 for directions on how to install the filters when replacing.
2. Fill in the usage start date of the filters on the Date Label.
Disposal of Filters
Please dispose of replaced filters according to the local disposal laws and regulations.
HEPA Filter Materials:
• Filter: Polypropylene  • Frame: Polyester
Active Carbon Filter Materials:
• Deodorizer: Activated charcoal  • Net: Polypropylene 60%, Polyester 40%
SPECIFICATIONS
Model
Power supply
Fan Speed Adjustment
Rated Power
Air Flow Volume (m
3/hour)
Applicable Floor Surface
Cord Length
Dimensions
Weight Fan
Speed
Operation
~38m
2*1
2.0m
338mm(W)x207mm(D)x620mm(H)
6.5kg MAX
46 W
306MED
8.6W
138SILENT
3.7 W
30
*1FU-S51A
220V   50Hz
•The applicable floor surface area is appropriate for operating the unit at maximum fan speed.
•Applicable floor surface area indicates the space where a certain amount of dust particles can be
removed in 30 minutes.
Standby PowerIn order to operate the electrical circuits while the power plug is inserted in
the wall outlet, this product consumes about 0.7W of standby power.
For energy conservation, unplug the power cord when the unit is not in use. 
						

							ENGLISH
E-13
Before calling for repair, please review the list below, since the problem may not be a unit malfunction.
SYMPTOMREMEDY (not a malfunction)
Odours and smoke are not
removed.•Clean or replace the filters if they appear to be heavily soiled.
(Refer to E-11, E-12)
The CLEAN-SIGN Light lights
green even when the air is
impure.•The air could be impure at the time the unit was plugged in.
(Refer to E-5) Pull out the plug from the electrical outlet, and
insert the plug one minute later.
The CLEAN-SIGN Light lights
yellow or red even when the air
is clean.•The sensitivity of the sensors become unstable when the
opening of the odour sensor or dust sensor is dirty or is clogged.
Clean the dust around the sensor opening using a vacuum
cleaner. (Refer to E-10)
The Plasmacluster Indicator
Light remains green (or blue)
and does not change.•When in Ion Control Mode (or Clean Mode),  the Plasmaclus-
ter Indicator Light  colour will not change.
•Clicking sound is emitted when the unit is in the Ion Control
Mode, and ticking sound is emitted when the unit is generating
ions.
If the sound is irritating, set the unit away from you.
A clicking or ticking sound is
heard from the unit.
TROUBLESHOOTING
ERROR DISPLAY
LAMP INDICATION REMEDY
The “Silent” Fan Speed Indica-
tor Light blinks.
Fan motor disconnected or abnormal.
Operation stops.
•Pressing the POWER ON/OFF button will reset the error
display, but if error occurs again, contact the Sharp Service
Centre.
The discharged air has an aroma
or odour.
•Check to see if the filters are heavily soiled.
Replace the filters.
•Plasmacluster Air Purifiers emit small traces of ozone which
may produce an odour. These ozone emissions are well below
safety levels .
The unit does not operate when
cigarette smoke is in the air.•Is the unit installed in a location that is difficult for the sensor
to detect cigarette smoke?
•Are the dust or odour sensor openings blocked or clogged?
(In this case, clean the openings.) (Refer to E-10)
The Plasmacluster Indicator
Light or the CLEAN-SIGN Light
will not activate.•Check to see if the Lights OFF Mode is selected. If so, then
press the Plasmacluster Ion Mode Selection Button for 3
seconds to activate the indicator lights.
(Refer to E-9)
Plasmacluster Indicator Light
(repeats colour cycles between
blue and green )
•The ION SHOWER operation is working. 
						

							!
•

•DVgÛ
ZÿÒùB
šdø©d	t·f
Jd	
ö-ÚÁ*a#
d	
ö-Ú¾V	yV]«d	d4I·@Ú«YzÌA@éc
5X	ð	”@éc5Yq5x5u5€5q@éc5X
«¢@éc5YdÍ
}Ty
°fd	

ö-Ú·@I«Å,ÂY6”Ù 
ä@ûf

5`5^5c÷˜¢PÛ5Yf….bÓ±µã¾@zÌA@écÛd©¼
É—V×f5X.bÓ±p—5x5u5€5q@écV×5Y




 
						

							•Ö
	$Ã
C-1
•Ö
µ}
†…
oJd	
ö-ÚfúZaØä­
üãdøM½4\	Ãf4\I*ܘ
Ãd
@aب ÄŒ+
°©µS·f
aØ|
­Mä­üãø©Ú_af
f}

vbN(	ð
=
-Y
vbN(	ð
=Á*|Ì6ó	÷

WYN(d(òÞÖ	ð€	jqe

=d
›Sd	•Y	7mee
=q@
½a
Yz
f
N(
›S

†Y-d	
ö-Ú콫d	K1
›
SNqMNYâ7f
•   
·|Ì

f
•  

N(|Ì
IÚ
Zì½ò¢q.b
М
»d	
Yîäûd
}þ
7l‰·|Ì
ÐN
›S|Ì5Zf
5ZN
›S|Ì
N6ø#YâQó(
›SN
Y;Ef
•  
@éc
5a5Y 

						

							C-2
 Č+
°
4\eœÛd@
²mÂ
?IÄŒk#
£Dd

						

							•Ö
C-3
 Č+
°
Á*Y!+
°
•¶
A
æV	yqTyf
•
•4\Û¶;óIÚf
•E
IÚÛd
²S\aeôÚÙYÓ[f

•¶¯ÚÞ@écY
‹1hÁ*IÚf
•¶
öyqŽ\5x5u5€5q@écf
•


Ä8Ì
•Á*IÚÛd
ZIÚÄõ
mÞe*Y£ê5X½e
VÚe×*ÚÐÛR5YÇ5b÷ø.fø#*[e

•¶Ä¯
М\
ŸÁ,yY®Ùf

•

•¶Ä¯_õ]	!
·þ¬çIÚ\
Ÿs£õ8‘¤Y®Ùf
5X¯5e5c5e]YG…
‹1h4\f5Y
•Ä@
²¢xdò·,»f

•¶Ä¯6*[
½gY®Ù5X½
						

							C-4
¢Å…¤H
ôÚÅ…
±¡
.b
М
ôÚ
5x5u5€5q@éc
5X
5_c
5Y

öyYzÌA@éc
Ú‚z
@écêV
Ã& 
 
vbN(	ð
=8jñ N(|Ì8jñ ,º8jñ €	j|Ì8jñ 
Á*8jñ