Sharp Ar M201 Manual

TROUBLESHOOTING AND MAINTENANCE
69
8
The MFP driver cannot be correctly installed by Plug and 
Play (Windows 2000/XP/Vista)
In Windows 2000/XP/Vista, if the MFP driver cannot be correctly installed by Plug 
and Play (for example, Plug and Play takes place without copying the required files 
for the MFP driver installation), follow these steps to remove unneeded devices and 
then install the MFP driver as explained in INSTALLING THE SOFTWARE (p.36).
1Click the start button, click Control Panel, and then...

70
MISFEED REMOVAL
When a misfeed occurs, the error indicator blinks, CLEAR PAPER JAM appears in 
the display, and the machine stops operating. If a misfeed occurs when using the 
RSPF, RETURN X ORIGINAL(S) START TO RESUME will appear in the display. 
(X indicates the number of pages to be returned.). This indicates the number of the 
originals that must be returned to the document feeder tray after a misfeed. Return 
the required number of originals. This number will be cleared when copying is 
resumed...

TROUBLESHOOTING AND MAINTENANCE
71
8
A: Misfeed in the paper feed area
1Gently remove the misfed paper from the paper feed area as 
shown in the illustration. If the error indicator blinks and the 
misfed paper is not visible in the paper feed area, pull out the 
paper tray and remove the misfed paper. If the paper cannot be 
removed, proceed to B: Misfeed in the fusing area.
2Close the side cover by pressing the round projections near 
the side cover open button. The error indicator will go out and 
the...

TROUBLESHOOTING AND MAINTENANCE
72
2Gently remove the misfed paper 
from under the fusing unit as shown 
in the illustration. If the paper cannot 
be removed, proceed to C: Misfeed 
in the transport area.
3Raise the fusing unit release lever and then close the side 
cover by pressing the round projections near the side cover 
open button. The error indicator will go out and the ready 
indicator will light up.
C: Misfeed in the transport area
1Lower the fusing unit release lever.
See B: Misfeed in the...

TROUBLESHOOTING AND MAINTENANCE
73
8
4Raise the fusing unit release lever, close the front cover and 
then close the side cover by pressing the round projections 
near the side cover open button. The error indicator will go out 
and the ready indicator will light up.
D: Misfeed in the RSPF (Option)
If the misfed original is at the top of the document feeder tray or in the exit area, 
follow procedure (A) to remove the misfeed. If the misfed original is inside the 
document feeder and is not visible,...

74
TONER CARTRIDGE REPLACEMENT
When toner is low, the error indicator will light up and TONER CARTRIDGE IS 
NEAR EMPTY. will appear in the display to alert you to purchase a new toner 
cartridge. If copying is continued while the indicator is lit, copies will gradually 
become lighter until the toner runs out. When the toner runs out, the machine will 
stop operating, the error indicator will blink, and REPLACE THE TONER 
CARTRIDGE will appear in the display. Follow the procedure below to replace the...

TROUBLESHOOTING AND MAINTENANCE
75
8
3Gently pull the toner 
cartridge out while pressing 
the lock release lever.
4Remove the toner cartridge from the bag. Grasp the cartridge 
on both sides and shake it horizontally four or five times. After 
shaking the cartridge, remove the toner seal.
5Gently insert the toner cartridge 
along the guides until it locks in 
place while pushing the lock release 
lever. Remove the tape from the 
shutter. Pull the shutter out of the 
toner cartridge as shown in the...

TROUBLESHOOTING AND MAINTENANCE
76
6Close the front cover and 
then the side cover by 
pressing the round 
projections near the side 
cover open button. The error 
indicator will go out and the 
ready indicator will light up.
7
SCAN HEAD LOCKING SWITCH
The scan head locking switch is under the original table. If the switch is locked (), 
the machine will not operate. Unlock the switch ( ) as shown below.
To lock the scan head locking switch, hold up the catch in illustration   and turn the 
centre knob...

77
8
CHECKING THE TOTAL COUNT
You can check the total number of pages output by the machine (all pages printed by 
the copy function and printer function), as well as the output counts of each function 
(number of copies, number of scanned pages, number of faxes, etc.). When a count 
reaches 999,999 it returns to 0.
1Press the [MENU] key.
Press the [ ] key ( ) or [ ] key ( ) 
until TOTAL COUNT appears, and then 
press the [ENTER] key.
2Press the [ ] key ( ) or [ ] key ( ) to 
display the count of each...

78
CLEANING THE MACHINE
Proper care is essential in order to get clean, sharp copies. Be sure to take a few 
minutes to clean the machine on a regular basis.
Cabinet
Wipe the cabinet with a soft, clean cloth.
Document glass and the back side of the original cover/RSPF
Stains on the glass, RSPF scanning window, cover or RSPF roller will also be 
copied. Wipe the glass, RSPF scanning window, cover and RSPF roller with a soft, 
clean cloth. If necessary, dampen the cloth with a glass cleaner.
Do not spray...