Sharp Ar M201 Manual

9
1
Chapter 1
1
This chapter provides basic information that you should know before using the machine.
PA R T  N A M E S
Document glass Paper output tray extension
Operation panel Power switch
Front cover Handles
Paper tray Power cord socket
Side cover
Fusing unit release lever
Side cover open button Transfer charger
Bypass tray paper guides Charger cleaner
Original output tray extension Paper holder arm
Paper output tray
Photoconductive
drum
RSPF (Option)
Original cover
Exit area
2
3
4
1
5
76
9
8
10...

PREPARATIONS
10
Operation panel
[MODE SELECT] key / Mode indicators
Press this key to select the mode. The 
indicator of the selected mode lights (copy, 
printer, scanner, fax mode indicators).
Display
This shows messages indicating the 
machine status and any problems that 
occur, as well as user programs and 
function setting menus. 
Numeric keys
Use these to enter the number of copies 
and other numerical settings.
The keys can also be used to select 
items in function setting menus.
[CLEAR] key ( )...

PREPARATIONS
11
1
[COPY RATIO] key
Press to select an enlargement or 
reduction ratio.
To select a preset ratio setting, press the 
[COPY RATIO] key and select the 
desired preset ratio. To select a ratio 
that is not preset, press the [COPY 
RATIO] key, select the preset ratio that 
is closest to the desired ratio, and then 
press the [ ] key ( ) or 
[] key 
( ) to increase or decrease the ratio in 
increments of 1%.
[CLEAR ALL] key ( )
This returns all functions to the default 
settings. When pressed...

12
CONNECTING THE POWER CORD
1Ensure that the power switch 
of the unit is in the OFF 
position. Insert the attached 
power cord into the power cord 
socket at the rear of the unit.
2Plug the other end of the power cord into the nearest outlet.
POWER ON AND OFFThe power switch is located on the left side of the machine.
Power onTurn the power switch to the ON position.
The ready indicator will light up and other indicators 
which show the initial settings of the display will also 
light up to indicate...

PREPARATIONS
13
1
Power off
Make sure that the machine is not in operation and then turn the power 
switch to the OFF position.
If the power switch is turned off while the machine is 
in operation, a misfeed may occur and the job that 
was in progress will be cancelled.
In cases where the machine will not be used for a 
long time, turn off the power switch and remove the 
power cord from the outlet.
Check the following to make sure the machine is not in operation:
 The ready indicator is lit. (Initial...

PREPARATIONS
14
Check original cover/RSPF open function
When enabled, this function may help prevent wasteful use of toner that occurs when 
the original cover/RSPF cover is not completely closed.
If the start ( ) key is pressed when the original cover/RSPF cover is not completely 
closed, CHECK ORIGINAL will appear in the display and copying may not take 
place. If copying does not take place, copying can be performed by pressing the start 
( ) key again, however, the scan size set in CHANGING A TRAYS...

15
2
Chapter 2
2
The tray location indicator will blink when there is no paper in the selected paper 
tray, or when the selected paper tray is not closed or is improperly closed.
PA P E R
For best results, use only SHARP recommended paper.
*1The number of sheets of paper that can be loaded varies depending on the weight of the paper.*2Do not use non-standard envelopes or envelopes that have metal clasps, plastic snappers, strings, 
windows, linings, self-adhesive strips, patches or synthetic materials....

16
LOADING THE PAPER TRAY
1Raise the handle of the paper tray 
and pull the paper tray out until it 
stops.
2Fan the paper and insert it into the tray. Make sure that the 
edges go under the corner hooks.
3Gently push the paper tray back into the machine.
Make sure that the paper is not torn, is free of dust, and has no wrinkles 
or curled edges.
 Do not load paper above the maximum height line ( ). 
Exceeding the line will cause a paper misfeed.
 If the paper is not fanned, double-feeds or misfeeds may...

17
2
BYPASS FEED (including special paper)
The bypass tray can be used to feed standard paper, transparency film, labels, 
envelopes, and other special purpose paper.
Important points when insert ing paper in the bypass tray
Up to 50 sheets of standard copy paper c an be inserted in the bypass tray. (Capacity 
will vary depending on the type of paper loaded.)
Be sure to place envelopes horizontally as shown in the following diagram.
• When loading envelopes, make sure that they are straight and flat and...

LOADING PAPER
18
Loading paper in the bypass tray
1Open the bypass tray and extend the tray.
2Set the bypass tray paper guides to the paper width. Insert the 
paper (print face down) all the way into the bypass tray.
3Press the [TRAY SELECT] key ( ) to select the bypass tray.
 Paper must be fed narrow side first into the feed slot.
 Special papers such as transparency film, labels, and envelopes 
must be fed one sheet at a time through the bypass tray.
 When copying onto transparency film, remove each...