Sega Virtua Striker 3 Kit Installation Service Manual

							1ST  PRINTING  MAY 01
MANUAL NO.  999-1283
SEGA ENTERPRISES, INC.  USA
Universal Kit
Kit Installation Instructions
& Service Manual
Switchable FROM High Resolution 31K
TO Standard (Low) Resolution 15.75K.
1 - 2 PLAYER GAME 
						

							Warranty
Your new Sega Product is covered for a period of 90 days from the date of shipment.  This certifies
that the Printed Circuit Boards, Power Supplies and Monitor are to be free of defects in workman-
ship or materials under normal operating conditions.   This also certifies that all Interactive Control
Assemblies are to be free from defects in workmanship and materials under normal operating condi-
tions.  No other product in this machine is hereby covered.
Sellers sole liability in the event a warranted part described above fails shall be, at its option, to
replace or repair the defective part during the warranty period.  For Warranty claims, contact your
Sega Distributor.
Should the Seller determine, by inspection that the product was caused by Accident, Misuse, Ne-
glect, Alteration, Improper Repair, Installation or Testing, the warranty offered will be null and void.
Under no circumstances is the Seller responsible for any loss of profits, loss of use, or other dam-
ages.
This shall be the exclusive written Warranty of the original purchaser expressed in lieu of all other
warranties expressed or implied.  Under no circumstance shall it extend beyond the period of time
listed above. 
						

							1
Virtua Striker 3
Sega Naomi System
Kit Contains List
Part #
400-5397-01
838-13616
560-5407-UL
838-13683-93CV1
400-5397
600-7141-200
600-7009-2500
840-0071D-01
600-7247-500
610-0630-0006
LOC. PURCHASE
XKT-0833
LOC. PURCHASE
LOC. PURCHASE
LOC. PURCHASE
999-1276
999-1277
999-1278
999-1280
999-1279
999-1281
Desc
NAOMI POWER SUPPLY
AUDIO POWER AMP 2 CH
AUDIO XFORMER 120V
JAMMA I/O BD (NAOMI)
POWER SUPPLY (NAOMI)
USB CABLE
VGA VIDEO CABLE
ASSY CASE PC1 DIMM BD
CABLE SCSI TYPE 2 500MM
GD SOFT KIT VS3
SERVICE SWT BRKT ASSY
GD-ROM DRIVE KIT
JOYSTICK 8 WAY - GREEN
PUSHBUTTON - GREEN
PUSHBUTTON - BLUE
MARQUEE ART
INSTR. SHEET #1 PLAYER
INSTR. SHEET #2 CONTR
CONT PNL NAOMI
DECAL SIDE ART
CONTRL PNL STND
Qty
1
1
1
1
1
2
1
1
1
1
1
1
2
2
2
1
1
1
1
2
1 
						

							2
SERVICE BULLETIN
SEGA Service Department                http://www.seuservice.com
45133 Industrial Drive           Phone: 415.701.6580
Fremont, Ca. 94538               Fax: 415.701.6594
If you have any questions please contact the SEGA Service Department at the numbers given above.
120Feb 9. 2000
The SEGA  Naomi Game kits are actually ‘JAMMA Dependent’.  What this means exactly is they will only
install into existing JAMMA Cabinets.  If an operator tries to install these kits into a Non-JAMMA cabinet,
they will first have to bring the wiring up to JAMMA Standards.
°Step 1 Disconnect the games original DC Power Supply.  You may only use the power supply provided
with your kit.  Be sure to set the voltages going to your Game BD to 5.1 and 3.3 volts DC to assure proper
operation ( Measure on Square Connector at Game BD.  Yellow = 5vdc / Brown = 3.3vdc / White = Gnd )
°Step 2 You MUST USE THE COIN METER SUPPLIED WITH YOUR KIT to assure proper Coin
acceptance.  A minimum 18 Gauge wire should be used from the Coin Meter 1 output line on your
JAMMA Harness.  The 5vdc ( Yellow ) wire found in the wiring bag of your kit MUST BE USED for the
supply voltage to the meter.
SPECIAL NOTICE FOR
ALL SEGA NAOMI KITS
PROBLEM:
SOLUTION:
Not following the directions provided herein may cause your game to malfunction.
All electrical work should be performed by the site’s Serviceman or Technician.
In order to prevent an electric shock and short circuit, be sure to turn power off before performing
work or touching the interior parts of the product.
Be careful so as not to damage wirings. Damaged wiring can cause an electric shock or short circuit
accident.
Do not touch places other than those specified. Touching places not specified can cause an electric
shock or short circuit accident. 
						

							3
INSTALLATION INSTRUCTIONS
1)  First.  Remove all access panels from the game.  Locate the original game Logic PCB’s & Power
Supply and remove from the Cabinet by first disconnecting all harnesses from the boards.  (You need
only to splice in the Main Power (110v AC) into the 3-Pin Connector (GRN/WHT/BLK).)
2)  Remove all existing game harnesses (we suggest using New Jamma Harnesses (NOT contained in the
kit) to ensure reliability).
3)   Locate the most convenient and open area of the cabinet to mount the Virtua Stiker 3  Naomi System
Assembly.  Make sure this area is free and clear of all cable harnesses and grounds, cable clamps, etc.
Vacuum out or clean bottom of cabinet of dirt & miscellaneous parts (e.g.
screws, loose coins / tokens, etc.).
Remove all exterior decals and repair any cabinet damage.  Repaint
cabinet if necessary.  Remove the Monitor Plexi or if your game plexi has
Silk-screened artwork, you will need to strip it off.
4)   Connect the JAMMA Harnesses to the JVS-JAMMA Interface Boards.  Separate the wires from each
other (i.e. Control Panel, Video, Speaker, Power Supply).  Run the various harnesses to the part of the
cabinet they go to ensuring they are dressed properly & secured to the cabinet.  Locate the Volume/
Speaker/Coin Meter Cable and connect to your existing Switch Bracket or use the new one included
with the kit.  Note: If you are using a VGA Compatible Monitor you can run your VGA Cable directly
to the monitor or connect it to your JVS JAMMA Interface for RGB Conversion to your JAMMA
Cables.
5)   Remove  Marquee from cabinet and cut to fit the new Virtua Striker 3  Marquee in place.
 REPLACE old Joysticks & Buttons with the NEW ones supplied in Kit.
6)   First remove all Joystick and Button assemblies from the Control Panel.  Remove Lexan and Control
Panel Overlay.  Proceed to clean surface of the Control Panel by removing all adhesive and dirt.  Fill
in or plug up existing button holes to set up a blank work area for your new controls.
7)   Install the new Control Panel Overlay by carefully peeling off the paper backing and laying down on
the panel.  Smooth it out, starting in the center and working your way to the edges (removing all of
the trapped air pockets).  If necessary, cut the edges of the overlay excess and fold under panel.
8)   Cut out the button and Joystick Holes.  Install Joystick and buttons from kit into the Control Panel
and tighten down.  Connect all game harness wires to switches and buttons. 
						

							4
INSTALLATION INSTRUCTIONS
9)  Proceed to place new decals on the sides of the cabinet.  Locate a new monitor bezel, if needed, and
replace glass, if required (due scratches).  Install Instruction Placard to the back of the Monitor Glass.
NOTE:  As a precaution, disconnect the JAMMA Harness from the I/O Boards and turn power on.  With a
Multi-Meter, measure the 5v and 3.3v. Adjust if necessary to 5.15v DCand 3.3vDC.  Measure the +12  to
ensure the wires and voltages are in the correct position.  Turn power off.  Plug in the JAMMA Harness once
again to the I/O Boards.  The Attract Mode should appear on the screen.
Adjust the SIZE, CONTRAST, BRIGHTNESS, and COLORS on the
Monitor for optimum appearance.  Adjust VERTICAL/HORIZONTAL
Hold to get a stable picture, if required.
Enter DIAGNOSTICS and adjust the Volume Level, test all Buttons &
Joystick for proper operation & wiring.  Adjust Pricing.  Coin-Up and
test out a game to ensure proper play functions are as they should be. 
						

							5
Coin Meter
TestService
Volume 
JAMMA Pin     R
JAMMA Pin    15 JAMMA Pin      1
Yellow Wire from Extra
Harness  (+5v)JAMMA Pin  8
+ _
Pin 1
Pin 5Pin 4 To CN1 of
Amplifier Board
YEL/RED
WHT/RED GRN/RED
From CN2 of
Amplifier Board
From CN4 of
Amplifier Board
GRY/RED
ORG/RED
ORG/BLUE GRY/BLUELeft
Speaker
Right
Speaker
Sega Naomi System Switch
Bracket and Speaker
Installation Diagrams
(Figure 3) 
						

							6
4 1
2
3
5
6
7
8
10
11
12
13
14
15
16
17
1
8
19
20
21A
B
C
D
E
F
H
J
K
L
M
N
P
R
S
T
U
V
X
Y
Z
a 22
23
24
4ed
26 25cb
28f 279
W
Ground
Ground Ground
Ground
+5v (Not Used)+5v (Not Used)
+5v (Not Used)+5v (Not Used)
(Not Used)(Not Used)
+12v (Not Used)+12v (Not Used)
KeyKey
Coin Meter 1
Coin Meter 2
(Not Used)
(Not Used)
(Not Used)(Not Used)
(Not Used)
(Not Used)
Video Red
Video Blue
Video GroundVideo Green
Video Sync
Service
Test
(Not Used)
Coin 1
Coin 2
1P Start
2P Start
1P UP2P UP
2P Down 1P Down
1P Left
2P Left
1P Right
Attack 1P (1P SW1)
Grapple 1P (1P SW2)
Support 1P (1P SW3)
 Ground
 Ground2P Right
Attack 2P (2P SW1)
 Ground GroundSupport 2P (2P SW3) Grapple 2P (2P SW2)
(Not Used)
(Not Used)(Not Used)
(Not Used)
Sega Naomi System
JAMMA Harness Wiring
(JAMMA I/O BD)
(Figure 4) 
						

							7
CN4
Sega Naomi System
Filter Board Information
Connector Description etc.
PSW2PSW1
CN3CN2CN1
DIPSW1
Power Connectors VGA Level
Video Out Preamp Level
Audio Out Test
 Switch Service
Switch
1
12
23
34
Setting for High
Resolution 31KHZ
1 -4 off
Setting for Standard
Resolution 15KHZ
1 on 2-4 off. 
						

							8 Minimum DIMM Memory Capacity
256 MB
PLAYER 1 PLAYER 2
1.  SPECIFICATIONS
ON-SCREEN DISPLAY
Monitor Position
Horizontal Synchronous Frequency
15/31 kHz
CONTROL PANEL
HORIZONTAL
8WAYS
SW1
SW3SW2
START SW1P 2P
8WAYS
SW1
SW3SW2
1
2
3