Sega Harley Davidson Std Type Service Manual

28
MANUAL SETTING
Selecting MANUAL SETTING in the COIN ASSIGNMENTS mode displays the following screen.
FIG. 7.11b MANUAL SETTING
BONUS ADDER NO  BONUS ADDER
2 COINS GIVE 1 EXTRA COIN
3 COINS GIVE 1 EXTRA COIN
4 COINS GIVE 1 EXTRA COIN
5 COINS GIVE 1 EXTRA COIN
6 COINS GIVE 1 EXTRA COIN
7 COINS GIVE 1 EXTRA COIN
8 COINS GIVE 1 EXTRA COIN
9 COINS GIVE 1 EXTRA COIN
Table 7.11c MANUAL SETTING
Determines Coin/Credit setting.
This sets how many coins should be inserted to obtain one Service Coin.
This sets how...

29 7 - 12  REAL TIME CLOCK TEST
     REAL TIME CLOCK TEST
25 DEC  1997 THRU 18: 55’30”
BATTERY O.K.
DAY 25
MONTH DEC
YEAR 1997
HOUR 18
MINUTE 55
SECOND 30
DAY OF THE WEEK THU
SET
>EXIT
                  SELECT WITH SERVICE BUTTON
                         AND PRESS TEST BUTTON
Fig. 7.12  REAL TIME CLOCK TEST
Fig. 7.13b  VOLUME SETTINGHANDLE BAR: After turning the handlebar fully to the left
and right, return it to the cneter and ensure the status in
which force is not exerted.
THROTTLE: After fully moving...

30
Clears the contents of BOOKKEEPING and high
score player ranking entry.
When clearing, bring the arrow to “YES” and when
not clearing, to “NO”, by using the SERVICE
BUTTON, and push the TEST BUTTON.
When the data has been cleared, “COMPLETED”
will be displayed. Bring the arrow to “NO” and
press the TEST BUTTON to cause the MENU
mode to return on to the screen.
Note that the contents of the GAME SETTING,
COIN SETTING, and BOARD SETTING are not
affected by BACKUP DATA CLEAR operation
.
BACKUP DATA...

31
8 . HANDLEBAR
In order to prevent an electric shock and short circuit, be sure to turn power off
before performing work by touching the interior parts of the product.
Be careful so as not to damage wirings. Damaged wiring can cause an electric shock
or short circuit accident.
8 - 1  ADJUSTING/REPLACING THE FRONT BRAKE VOLUME
1
2In the test mode, if the Front Brake Volume’s Value movements are irregular, adjust or replace the Volume by
using the following procedure:
Take out the 4 screws and remove the...

32
1
2 VOLUME ADJUSTMENT
Loosen the 2 screws which secure the VR
bracket to move the VR Bracket.
Move the VR Bracket to disengage the
gear mesh.
By adjusting gear mesh, fasten the 2
screws which secure VR Bracket.
Move the Brake Lever fully to the movable
range and check if the Volume Shaft’s
revolvable range is exceeded.
After adjustment, be sure to perform the
Volume setting in the Test Mode.
3
4
5
1
2 VOLUME ADJUSTMENT
Replace the Volume if it is malfunctioning.
Install the Volume in the manner so...

33 8 - 3  ADJUSTING/REPLACING THE HANDLEBAR VOLUME
 In the Test Mode, if the HandleBar Volume’s value movements are irregular, adjust or replace the Volume.
1
2Remove the 4 screws.
Disconnect the 3 connectors and remove
the mask cover.
When the mask cover is removed, monitor
screen adjustment knob appears.TRUSS SCREW (4)
M4x8 (black)
CONNECTORS
ADJUSTMENT KNOB 

34
Remove the bolt w/hexagon hole and pull out the
handle from the shaft.
Take out the 3 screws, disconnect the connector inside the tank, and remove the tank.3
4Bolt w/hexagon hole
M10x20,
w/flat and spring washers
TRUSS SCREW (3)
M4x12, Flat washerCONNECTOR
8P YELLOW 

35
Remove the 4 hexagon nuts which secure the
centering mecha. By viewing the centering mecha
from above, remove the hexagon nuts from the
four corners only.
Carefully lift the centering mecha and disconnect
the connector connected to the centering mecha.5
6SCREW (1)
M4x8,
w/ flat and spring washers
HEXAGON NUT (4)
M8
w/ flat and spring washers 

36
Do not touch places other than those specified. Touching placers not specified can
cause an electric shock and /or short circuit accident. V.R. ADJUSTMENT
Loosen the 2 screws which secure the V.R.
Bracket to move the V.R. Bracket.
Move the V.R. Bracket to disengage ADJUST
GEAR mesh and move the V.R. shaft in the
manner so that the V.R. shaft cut portion faces
the oppisite side of ADJUST GEAR as shown.
Have the gears meshed and tighten the 2
screws.
Carefully turn the Handle Shaft to left/right
and...

37
8 - 4  GREASING
Be sure to use the designated grease. Using undesignated grease can cause parts
damage.
Do not apply greasing to places other than those specified. Greasing to undesignated
places can cause malfunctioning and the quanlitative deterioration of parts.
GEAR MESH PORTION
(FRONT V.R.)
GEAR MESH PORTION
(ACCELERATOR)
SLIDING FACE OF BRAKE
GEAR MESH PORTION
(FRONT V.R.) Once every three months, apply greasing to the following places.
For Greasing use Grease Mate (P.No. 090-0066).