Sanyo Vpc S60ex Instruction Manual

95English
INITIALIZING THE CARD MEMORY AND INTERNAL MEMORY
A card must be formatted with this camera:
iAfter purchasing, when used for the first time, or
iIf it was formatted using a personal computer or another digital camera.
The card cannot be reformatted if the lock switch is set to the “LOCK” 
position. Proceed with the reformat procedure after setting the lock switch to 
the unlocked position.
1 To reformat a card, install it in the camera. To reformat the camera’s 
internal memory, remove the card...

English96
4 Select the desired format option, and press the SET button.
hThe Confirm Format Screen appears.
5 Select “YES”.
6 Press the SET button.
hFormatting begins.
hDuring formatting, “FORMATTING” and “DO NOT POWER OFF” are 
shown on the monitor.
CAUTION
Caution during reformatting
iPlease do not turn off the camera or insert/remove the card while the card 
is being formatted.
Reformatting erases the data
iWhen the card or internal memory is initialized, all the recorded data is 
erased. Protected...

97English
RESETTING THE CAMERA SETTINGS
Reset the camera to the factory-preset settings.
1 Display the Option Menu (page 82).
2 Select “RESET SETTINGS” and 
press the SET button.
hThe Reset Settings Menu appears.
YES:
Reset to the factory-preset settings.
NO:
Do not change the settings, and 
return to the Option Menu.
3 Select “YES”, and press the SET 
button.
hThe camera settings are reset to 
the factory-preset settings.
HINT
iNote that the following settings do not change with this procedure:
Date and...

English98
CHECKING THE REMAINING INTERNAL 
MEMORY AND CARD MEMORY
You can check the possible number of images, audio recording time and 
video clip recording time remaining on the card. For a table showing the 
maximum number of images and recording time for the internal memory and 
for a specific card, please see “Possible Number of Images/Video Recording 
Time/Audio Recording Time” on page 128.
1 Press the ON/OFF button to turn the 
camera on.

Set the shooting mode to the single 
shot or sequential...

99English
CHECKING THE REMAINING INTERNAL MEMORY 
AND CARD MEMORY
For audio data
1 Set the camera to the audio 
recording mode (page 59).
hThe remaining audio recording time 
is shown.
HINT
iWhen the remaining number of images or the remaining video recording 
time is “0”, you cannot capture any more images. To capture more images, 
either install a new card, or save the images to a computer and then erase 
them (page 37) from the card.
iWhen the remaining number of images or the remaining video...

English100
CHECKING THE REMAINING BATTERY CHARGE
When using batteries, the remaining battery charge can be checked on the 
monitor. Make sure to check this indicator before capturing an image. For an 
indication of the possible length of time for battery operation, see page 127.
1 Press the ON/OFF button to turn the 
camera on.
hThe battery remaining charge 
indicator appears in the lower right 
corner of the monitor.
hDue to the battery characteristics, 
when the ambient temperature is 
low,   may...

101English
CHECKING THE REMAINING BATTERY CHARGE
HINT
iIf any data is present, you can also check the remaining battery charge on 
the Information Screen (page 81).
iBattery life may differ even among batteries of the same type.
iDepending on the usage of the camera (such as the number of times the 
flash is used, etc.) or the ambient temperature (temperatures below 10°C 
[50°F]) the number of images that can be saved on fully charged batteries 
will vary greatly.
iIt is recommended that you prepare...

English102
OTHER DEVICES AND CONNECTIONS
CONNECTING TO A TV
Connect the supplied AV interface cable from the PC/AV terminal on the 
digital camera to the AUDIO and VIDEO input terminals on the TV. 
Playback iAfter connecting the digital camera to the television, set the TV input switch 
to VIDEO input.
iWhen an AV interface cable is connected, no image appears on the 
camera’s monitor. 
iThe playback method is the same as when viewing images on the 
camera’s monitor.
iThe same playback procedure as when...

103English
DIRECT PRINTING
Your camera supports the PictBridge function. By connecting the camera 
directly to a PictBridge-enabled printer, the camera’s monitor can be used to 
select images and initiate printing (PictBridge printing).
Print preparations
1 Insert the card containing the images you wish to print in the 
camera.
2 Turn the printer on, use the supplied USB interface cable to connect 
the camera to the printer, and turn the camera on.
hConnect the camera’s PC/AV terminal to the printer’s...

English104
3 Select “PictBridge”, and press the 
SET button.
hThe screen to select the images to 
print appears.
CAUTION
Caution when connecting a printer
iIf the power to the printer is turned off while it is connected, the camera 
may not operate correctly. If the camera does not operate correctly, 
disconnect the USB interface cable, turn off the camera, and then 
reconnect the cable.
iDuring PictBridge printing, the camera’s button operation response is 
slower.
iIf the camera is powered by batteries...