Sanyo Vpc S60ex Instruction Manual

							95English
INITIALIZING THE CARD MEMORY AND INTERNAL MEMORY
A card must be formatted with this camera:
iAfter purchasing, when used for the first time, or
iIf it was formatted using a personal computer or another digital camera.
The card cannot be reformatted if the lock switch is set to the “LOCK” 
position. Proceed with the reformat procedure after setting the lock switch to 
the unlocked position.
1 To reformat a card, install it in the camera. To reformat the camera’s 
internal memory, remove the card from the camera.
2 Display the Option Menu (page 82).
3 Select “FORMAT” and press the 
SET button.

hThe screen to select the type of 
format appears.
hFollow steps 4 to 6.
FORMAT:
A normal formatting is executed.
FULL FORMAT:
The entire card is scanned and 
reformatted. It is not possible to 
select this when there is no card 
installed, or when the remaining 
battery charge is low.

hThe screen to begin formatting 
appears.
hFollow steps 5 and 6.FORMAT (    CARD)FORMAT (    CARD)
FORMAT
FULL FORMAT
OK
OK

YES
NO
OK
OK
Format the internal memory?Format the internal memory?

Downloaded From camera-usermanual.com Sanyo Manuals 
						

							English96
4 Select the desired format option, and press the SET button.
hThe Confirm Format Screen appears.
5 Select “YES”.
6 Press the SET button.
hFormatting begins.
hDuring formatting, “FORMATTING” and “DO NOT POWER OFF” are 
shown on the monitor.
CAUTION
Caution during reformatting
iPlease do not turn off the camera or insert/remove the card while the card 
is being formatted.
Reformatting erases the data
iWhen the card or internal memory is initialized, all the recorded data is 
erased. Protected data is also erased, so before reformatting a card, any 
data you want to keep should be copied to your personal computer’s hard 
disk or other storage medium.
Caution regarding disposing/transferring the card (recovering data from 
a reformatted card)
iIf a card is reformatted or the data is erased from the card using the 
camera or a computer, the card’s control data may be merely modified and 
the data itself may not be completely erased from the card.
iIn some cases it may be possible to recover the data from a reformatted 
card using special software for that purpose. However, if the camera is 
used to execute a full format, it will be impossible to recover the data even 
by the use of data recovery software.
iIf you are disposing of a card, it is recommended that you physically 
destroy it. If you are transferring the card to someone else to use, it is 
recommended that you use the camera’s full format function to reformat 
the card, or use commercially available software for erasing card data. 
Managing data is the responsibility of the user.
HINT
To cancel reformatting
iIn step 5, select “NO”, and press the SET button.
Downloaded From camera-usermanual.com Sanyo Manuals 
						

							97English
RESETTING THE CAMERA SETTINGS
Reset the camera to the factory-preset settings.
1 Display the Option Menu (page 82).
2 Select “RESET SETTINGS” and 
press the SET button.
hThe Reset Settings Menu appears.
YES:
Reset to the factory-preset settings.
NO:
Do not change the settings, and 
return to the Option Menu.
3 Select “YES”, and press the SET 
button.
hThe camera settings are reset to 
the factory-preset settings.
HINT
iNote that the following settings do not change with this procedure:
Date and time setting
Language setting
AUTO POWER OFFFILE NO. RESET
FORMAT
RESET SETTINGS
OPTION MENU (2/2)
YES
NO
Downloaded From camera-usermanual.com Sanyo Manuals 
						

							English98
CHECKING THE REMAINING INTERNAL 
MEMORY AND CARD MEMORY
You can check the possible number of images, audio recording time and 
video clip recording time remaining on the card. For a table showing the 
maximum number of images and recording time for the internal memory and 
for a specific card, please see “Possible Number of Images/Video Recording 
Time/Audio Recording Time” on page 128.
1 Press the ON/OFF button to turn the 
camera on.

Set the shooting mode to the single 
shot or sequential shots shooting 
mode (page 27).

Set the shooting mode to the video 
clip recording mode (page 27).
hThe remaining recording time is 
shown on the monitor.
hThe remaining number of images 
and video recording time will differ 
depending on the resolution setting.Remaining number of images
Remaining recording time


Downloaded From camera-usermanual.com Sanyo Manuals 
						

							99English
CHECKING THE REMAINING INTERNAL MEMORY 
AND CARD MEMORY
For audio data
1 Set the camera to the audio 
recording mode (page 59).
hThe remaining audio recording time 
is shown.
HINT
iWhen the remaining number of images or the remaining video recording 
time is “0”, you cannot capture any more images. To capture more images, 
either install a new card, or save the images to a computer and then erase 
them (page 37) from the card.
iWhen the remaining number of images or the remaining video recording 
time is “0”, it may be possible to capture a few more images by changing 
the resolution setting or video clip mode setting (page 58).
iThe maximum number of images is 9,999, and the maximum video/audio 
recording time is 99:59:59. Note that if a large-capacity card is used, the 
remaining number of images or recording time may not be correctly 
displayed.
Remaining time
Downloaded From camera-usermanual.com Sanyo Manuals 
						

							English100
CHECKING THE REMAINING BATTERY CHARGE
When using batteries, the remaining battery charge can be checked on the 
monitor. Make sure to check this indicator before capturing an image. For an 
indication of the possible length of time for battery operation, see page 127.
1 Press the ON/OFF button to turn the 
camera on.
hThe battery remaining charge 
indicator appears in the lower right 
corner of the monitor.
hDue to the battery characteristics, 
when the ambient temperature is 
low,   may appear early for an 
incorrect indication of the remaining 
charge.
Also, depending on the conditions 
of use of the camera or the ambient 
conditions (temperature, etc.), the 
indicated remaining charge may 
change. Therefore, this indication 
can only be used as a general 
approximation of the remaining 
charge.
Battery 
remaining 
charge indicatorBattery remaining charge
Approx. full.
(This indicator appears only in certain 
operation modes.)
Power is low.
It will soon be impossible to capture or play 
back images.
If this icon flashes when the shutter button 
is pressed, images cannot be captured. 
Replace the batteries.
Battery remaining 
charge indicator
Downloaded From camera-usermanual.com Sanyo Manuals 
						

							101English
CHECKING THE REMAINING BATTERY CHARGE
HINT
iIf any data is present, you can also check the remaining battery charge on 
the Information Screen (page 81).
iBattery life may differ even among batteries of the same type.
iDepending on the usage of the camera (such as the number of times the 
flash is used, etc.) or the ambient temperature (temperatures below 10°C 
[50°F]) the number of images that can be saved on fully charged batteries 
will vary greatly.
iIt is recommended that you prepare extra batteries when taking pictures at 
a wedding or while traveling, for example, so you don’t miss capturing 
images of important moments due to the battery power running out. The 
same is recommended for taking photos in cold environments. (In a ski 
area, for example, the batteries can be kept warm in your pocket until 
ready to use.)
Downloaded From camera-usermanual.com Sanyo Manuals 
						

							English102
OTHER DEVICES AND CONNECTIONS
CONNECTING TO A TV
Connect the supplied AV interface cable from the PC/AV terminal on the 
digital camera to the AUDIO and VIDEO input terminals on the TV. 
Playback iAfter connecting the digital camera to the television, set the TV input switch 
to VIDEO input.
iWhen an AV interface cable is connected, no image appears on the 
camera’s monitor. 
iThe playback method is the same as when viewing images on the 
camera’s monitor.
iThe same playback procedure as when playing back with the camera is 
used to play back voice memos and audio recordings as well.
Voice memo playback: see page 33 
Audio playback: see page 60
CAUTION 
Insert and pull out the cable carefully
iWhen connecting the cables, make sure that the cable plugs are correctly 
oriented and that they match the shapes of the terminal sockets on the 
devices. Push the plugs in straight when connecting them. If undue force is 
used to connect a cable, it may permanently damage the connector pins in 
the terminal socket.
iDo not use excessive force when connecting and disconnecting cables.
PC /AV
To the VIDEO input 
terminal
White plugTo the PC/AV 
terminal Yellow plug
To the AUDIO input 
terminal
Switch input to VIDEOSupplied dedicated 
AV interface cablePC/AV terminal Open
Downloaded From camera-usermanual.com Sanyo Manuals 
						

							103English
DIRECT PRINTING
Your camera supports the PictBridge function. By connecting the camera 
directly to a PictBridge-enabled printer, the camera’s monitor can be used to 
select images and initiate printing (PictBridge printing).
Print preparations
1 Insert the card containing the images you wish to print in the 
camera.
2 Turn the printer on, use the supplied USB interface cable to connect 
the camera to the printer, and turn the camera on.
hConnect the camera’s PC/AV terminal to the printer’s USB connector.
hThe USB Connection Screen appears on the camera’s monitor.
USB CONNECTIONUSB CONNECTION
CARD READER
PictBridge
CANCEL
PC /AV
PC/AV
terminal
Supplied dedicated USB 
interface cableOpen
To USB connector
on the printer
Downloaded From camera-usermanual.com Sanyo Manuals 
						

							English104
3 Select “PictBridge”, and press the 
SET button.
hThe screen to select the images to 
print appears.
CAUTION
Caution when connecting a printer
iIf the power to the printer is turned off while it is connected, the camera 
may not operate correctly. If the camera does not operate correctly, 
disconnect the USB interface cable, turn off the camera, and then 
reconnect the cable.
iDuring PictBridge printing, the camera’s button operation response is 
slower.
iIf the camera is powered by batteries for printing, make sure that the 
remaining battery charge is sufficient.
Insert and pull out the cable carefully
iWhen connecting the cables, make sure that the cable plugs are correctly 
oriented and that they match the shapes of the terminal sockets on the 
devices. Push the plugs in straight when connecting them. If undue force is 
used to connect a cable, it may permanently damage the connector pins in 
the terminal socket. 
iDo not use excessive force when connecting and disconnecting cables.
PRINTPRINTPRINT
Print this image?Print this image?
COPIES 1
Downloaded From camera-usermanual.com Sanyo Manuals