Sanyo Vcc4594 P Manual
Have a look at the manual Sanyo Vcc4594 P Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 550 Sanyo manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
CONNECTIONS(VCC-4592P only) Basic connection for monitoring or recording The peripheral devices (VCR, monitor, lens, etc.) and cables are sold separately.1 Make the video signal connection between the camera and the monitor or time lapse VCR. 2 Use a commercially available 12 V DC adaptor. Connect an DC 12 V power source to the 12 V DC input terminal on the back of the camera. 2A: When using this unit, the supplied clamping core (A or B) must be installed on the power cord and BNC cable, in order to prevent electromagnetic interference to the other devices connected. 3 The POWER indicator (A) will light. Adjust the picture on the monitor using the Brightness and Contrast controls.Coaxial cable type and maximum lengthÃCable type RG-59U (3C-2V), 250 m maximum.ÃCable type RG-6U (5C-2V), 500 m maximum.ÃCable type RG-11U (7C-2V), 600 m maximum. CAUTION:ÃThe RG-59U type cable should not be run through electrical conduits or through the air.ÃUsing CCTV/Video-grade coaxial cable. (Video signal connections) : VIDEO IN : VIDEO OUT (A) 1 2A 2A 2 2A (A) (A) (B) NC+– – +DC 12 V 2A (B) L53Z4/XE GB 2001, 5, 23 10 English
SETTINGSThe illustration shows the factory default settings for the switches in the camera setup section. The camera settings are described on the assumption that a DC type auto iris lens is being used. If you are using a VIDEO type auto iris lens, be sure to read the Note which is given. Furthermore, refer to the sticker on the inside of the cover for details on DIP switch positions. Control name Position 1 Colour and Black/White level switch (Normal: L/High sensitivity: H)L 2 High speed electronic shutter setting 1/50 sec. 3 Electronic Iris (EI)/Auto iris (AI) setting AI 4 Aperture compensation setting (Sharp: SHRP/Normal: NOR)SHRP 5 Backlight compensation mode setting (MULT/OFF)OFF 6 Backlight compensation setting (BLC) (CENT/OFF)OFF 7 White balance switch (WB) and colour (R or B) adjustment volumeATW 8 External sync setting (SYNC: LL/INT) (VCC-4594P only)INT 9 External sync setting (SC-P1) (VCC-4592P only)adjustable F External sync horizontal adjustment (H-P) adjustable G Auto-iris lens setting (A.I. LENS), see page 5 DC H Lens iris level adjustment adjustable 1C-BWL H 9 8 ON 67 5 4 DC VIDEOA. I. LENSVR301H VR302 VR303 IRIS SC/SYNC A I E I OFF ATW NOR OFFMULT M SHRP LLSC-P1AP BLC WB 7 3 4 7 8 G 5 6 BLUE R E D 3 2 1 10 3 2 1 ES MSB LSB VR304 LEVEL 2 H-P CENT 9 F L53Z4/XE GB 2001, 5, 23English 11
SETTINGS High speed electronic shutter setting Normally, the speed setting switches for the high speed electronic shutter are all set to the down (OFF) position. This sets the electronic shutter speed to 1/50 sec. The switches can be set as indicated in table A to select one of the 8 speeds available.CAUTION:ÃWhen using the high speed electronic shutter, the switch 4 must be set to the down (AI) position.ÃUsing the high speed electronic shutter indoors with low lighting, will give darker pictures. In such a case, add some lights to make sure the lighting is sufficient. If the lighting is very bright, pay attention to the light angle in order to avoid or minimize the smear phenomenon effect. Table A (switch 1 ~ 3) 11/50 21/120 31/250 41/500 51/1000 61/2000 71/4000 81/10000(Unit: sec.) Iris function setting This should normally be set to the down (AI) position. Use a manual or fixed iris lens and set the lens aperture to the shortest F stop. Set the switch 4 (IRIS) to the up (EI) position.+ When using an auto-iris lens (for indoor/outdoor use) Set the switch 4 (IRIS) to the down (AI) position. Note:ÃThe electronic iris is suitable for normal indoor use. When the switch 4 (IRIS) is set to the up (EI) position, do not use an auto-iris lens.ÃIf used under fluorescent light, the image may flicker. In such a case, change to incandescent lighting or set the switch 4 (IRIS) to the down (AI) position and use an auto-iris lens.ÃWhen shooting bright subjects, pay attention to the light angle in order to avoid or minimize the smear phenomenon effect.ÃIf conditions are outside the electronic iris operation range or more than the maximum illumination, it will cause saturation of the CCD. In that case, use a manual iris lens.Aperture The initial setting for switch 5 is up (SHRP) so that the contours of the object are emphasized. However, if the contours of the object are already emphasized more than required, set switch 5 to the down (NOR) position. 123 23 1 231 231 123 231 231 231 45 L53Z4/XE GB 2001, 5, 23 12 English
SETTINGS Backlight compensation setting This camera has two different backlight compensation functions: Normally backlight compensation switch 6 (MULT) and 7 (CENT) are set to the down (OFF) position. Change the backlight compensation switch settings depending on the conditions.ÃMULT mode:Use this position when applying backlight compensation to the whole of the screen.ÃCENT mode:Use this position when applying backlight compensation to only the central portion of the screen. Note:ÃIf switches 6 and 7 are set to the up (ON) position at the same time, the MULT setting will have priority.ÃWhen MULT mode is set, scenes with no backlighting may appear extremely dark and the object may appear over-exposed. If this happens, set to CENT mode.If using a VIDEO type auto-iris lens ÃThe ALC volume on the lens should be turned all the way to Av (Average).ÃIf the backlight compensation function does not compensate properly for the conditions, set using the LEVEL volume on the lens. 6 7 (MULT mode: 64 sections)(CENT mode) L53Z4/XE GB 2001, 5, 23 English 13
SETTINGS White balance adjustment Normally the switch 8 (WB) is set to the down (ATW: auto white balance) position and the white balance is adjusted automatically. If a manual white balance adjustment is necessary, follow the steps below. Set the switch 8 (WB) to the up (M: manual) position, then adjust the colour.ÃTurn RED (VR302) to set the red ratio and/or BLUE (VR303) to set the blue ratio. Synchronization settingsThe default setting is internal synchronization (INT). You can change the power supply synchronization by moving switch 9 to the up (LL) position. Refer to ©Line phase adjustmentª for details. Line phase adjustment (VCC- 4594P only) When using a camera switcher to connect 2 cameras or more to one monitor, there may be a vertical roll of the images when switched. In such a case, set as described below.1 Set the switch 9 (SYNC) to the up (LL) position. 2 Switch the display on the monitor from camera 1 to camera 2. Adjust the LINE PHASE volume on camera 2 until the vertical roll of the image stops. If more than two cameras are used, please repeat this procedure for all the cameras. CAUTION:If the vertical roll cannot be corrected by setting the LINE PHASE volume on camera 2, try setting the LINE PHASE volume on camera 1. If it still cannot be corrected, please check that the polarity of the power cords of all connected devices is correct. 8 VR302 VR303 BLUER E D 9 L53Z4/XE GB 2001, 5, 23 14 English
SETTINGS External sync adjustment (VBS) (VCC-4592P only) 1Connect the VBS signal output for the other camera to the VBS IN connector at the rear of this camera. 2 If the signals are not synchronized, change the sub-carrier (SC-P1) switches as follows. Setting 9-pin 10-pin DefaultOFF (down) OFF Set to 90Æ counterclockwiseOFF ON (up) Set to 180Æ counterclockwiseON OFF Set to 270Æ counterclockwiseON ON Note: ÃThe sub-carrier switches let you make broad adjustments to the sub-carrier phase. If finer adjustments are required, contact the place of purchase.ÃThe type and length of the cable which is connected to the VBS connector may cause the horizontal synchronization being out of phase. If this happens, adjust VR304 (H-P: horizontal sync). Lens iris adjustment If using a DC type auto-iris lens, you will need to set the LEVEL (VR301) volume when shooting in the conditions described below. L (counterclockwise):To decrease the contrast H (clockwise):To increase the contrastÃIf shooting simultaneously in a dark room and through a bright window.ÃIf the subject background is extremely bright or dark.ÃIf the brightness of the picture on the monitor is not correct. 10 9 VR304 H-P VR301LEVEL L53Z4/XE GB 2001, 5, 23English 15
SETTINGS C Ã B/W (colour/black and white) switch setting This switch lets you select the timing of the automatic switching of the optical filter to colour image or black and white image, according to the subject brightness. The default setting is ©Lª. Set the switch according to the brightness. (Fig. 2) H: for a brighter setting than L L: Standard setting Notes:ÃAfter the power has been turned off, switching will restart from colour, when the power is restored.ÃA sound may be heard when the colour image or black and white image is switched. Also, the image will be distorted as shown in Fig. 2, this is normal and does not indicate a problem.ÃWhen using infrared lighting, if there is a strong reflection on the subject, the optical filter may switch from black and white to colour mode, Use only enough infrared lighting so that the mode is not switched.ÃThe focus setting may be different in black and white mode and colour mode. Please check the focus setting in both modes. Manual colour/black and white setting Connect each pin of the CONTROL terminal as indicated below, to set the image to black and white or colour as desired.ÃColour image setting Connect the C (colour) and the G (ground) pins.ÃBlack and white setting Connect the B (black and white) and the G (ground) pins.CONTROL terminal Image CB OFF OFF Auto OFF ON Black and white ON OFF colour ON ON Auto ON: Close OFF: Open Notes:ÃThe maximum length of cable for CONTROL terminal is 600 m (AWG 24).ÃDuring optical filter switching, even if the manual switching operation is done, you cannot determine if the image is black and white or colour. Manual switching will have to be done one more time. C-BWL H GC BCONTROL L53Z4/XE GB 2001, 5, 23 16 English
TROUBLESHOOTINGBefore taking the camera for repairs, please check below to make sure that the camera is used correctly. If it still does not perform correctly, please consult your dealer or a Sanyo Authorized Service Centre. No picture on the monitor screenÃIs the power turned on to all connected devices? Is the voltage correct?ÃAre all the signal connecting cables correctly connected?ÃIs the lighting sufficient?ÃHas the lens cap been removed?ÃIs the lens type (DC or VIDEO) correctly selected? Depending on the type of lens, the A. I. LENS switch must be set accordingly.ÃIs the iris control correctly set? A:When using a DC type lens, the LEVEL volume (inside the camera casing) should be adjusted. B:When using a VIDEO type lens, the LEVEL volume (on the lens) should be adjusted.The picture is not clearÃIs the monitor correctly adjusted?ÃIs the flange-back position correctly set?ÃIs the lens focus correctly adjusted?ÃAre the lens surfaces clean? If there is dust or finger prints on the lens, the image quality will deteriorate. To clean the lens use a soft cloth or a commercially available lens cleaning set. SERVICEThis camera is a precision instruments and if treated with care, will provide years of satisfactory performance. However, in the event of a problem, the owner is advised not to attempt to make repairs or open the cabinet. Servicing should always be referred to your dealer or Sanyo Authorized Service Centre. L53Z4/XE GB 2001, 5, 23English 17
SPECIFICATIONS Camera: Scanning system :PAL standard (625 TV lines, 25 frames/sec.) Interlace:PLL 2:1 interlace Image device:1/3 inch solid state image device CCD Picture elements:795 (H) x 596 (V) Effective picture elements:752 (H) x 582 (V) Synchronizing system:Internal sync, External sync, Line lock (VCC-4594P only) Resolution:520 TV lines horizontally, 400 TV lines vertically Video output level:1.0 Vp-p/75 ohms, composite Video S/N ratio:More than 48 dB Minimum required illumination (incandescent lighting):Approx. 0.03 lux with a F 1.2 lens (B/W mode), Approx. 0.6 lux with a F 1.2 lens (colour mode) Control terminal:Manual colour/black and white setting Backlight compensation:Manual MULT/CENT switching (Active when using an auto-iris lens) Iris function:Manual EI/AI switching Electronic iris range:0.6 lux to 35,000 lux (F 1.2, lens: colour mode) 1.0 lux to 50,000 lux (F 1.4, lens: colour mode) Electronic shutter:8 speeds, selectable by switches: (1/50, 1/120, 1/250, 1/500, 1/1000, 1/2000, 1/4000, 1/10000 sec.) Flange-back:12.5 mm ± 0.5 mm White balance:ATW/Manual switching Lens mount:CS mountEnvironmental conditions :Temperature: Ä10ÆC ~ +50ÆC Humidity: less than 90% (no condensation) Power supply:24 V AC, 50 Hz (VCC-4594P) 12 V DC (VCC-4592P) Power consumption:VCC-4594P: 4.1 W (with auto iris lens) 3.2 W (without auto iris lens) VCC-4592P: 3.3 W (with auto iris lens) 2.6 W (without auto iris lens) Weight:Approx. 450 g (without lens) Dimensions: mm Features and specifications are subject to change without prior notice or obligations. 136 126.5 1 15.4 25.211 1/4”–20 UNC67 54 28 3 L53Z4/XE GB 2001, 5, 23 18 English