Sanyo Vcc4594 P Manual

							INSTRUCTION MANUAL
BEDIENUNGSANLEITUNG
MANUEL DINSTRUCTIONS
VCC-4594P
VCC-4592P
COLOUR CCD camera
CCD-Farbkamera
Cam‚ra CCD COULEUR
CCD
About this manualÃ
Before installing  and using the camera, please read this manual
carefully. Be sure to keep it handy for later reference.
Ã
This manual gives basic connections and operating instructions for 2
PAL models (VCC-4594P, 4592P).
šber diese BedienungsanleitungÃ
Lesen Sie bitte vor der Montage und dem Inbetriebnehmen der
Kamera zuerst diese Bedienungsanleitung sorgf„ltig durch und
bewahren Sie sie zum sp„teren Nachschlagen auf.
Ã


A propos de ce manuelÃ
Avant dinstaller et dutiliser la cam‚ra, veuillez lire ce manuel
attentivement. Gardez-le … port‚e de main pour toute r‚f‚rence
ult‚rieure.
Ã
Ce manuel couvre les branchements et instructions pour
lutilisation de base pour 2 modŠles de format PAL
(VCC-4594P et 4592P).
2
PA L
VCC-4594P, 4592P
L53Z4/XE GB 2001, 5, 23 
						

							Depending on the conditions of use, installation and environment,
please be sure to make the appropriate settings and adjustments. If
you need help with installation and/or settings, please consult your
dealer.CONTENTSPRECAUTIONS ........................................................................................ 2
PARTS NAMES........................................................................................ 3
CONCERNING AUTO-IRIS LENSES ......................................................... 5
FLANGE-BACK ADJUSTMENT ................................................................ 6
MOUNTING THE LENS ........................................................................... 7
CONNECTIONS ....................................................................................... 9
SETTINGS ................................................................................................11
TROUBLESHOOTING ..............................................................................17
SPECIFICATIONS.....................................................................................18
FEATURESÃThe optical filter is switched automatically to colour image or
black and white image according to the subject brightness.ÃBuilt-in interline transfer method 1/3 CCD, approx. 410,000
picture elementsÃLow smear, anti-blooming, low lag, no burning and no geometric
distortion using the CCD solid state image device.Ã100% solid state components giving excellent immunity to shock
and vibrationÃNot subject to interference from magnetic or electrostatic fieldsÃHigh sensitivity, minimum required illumination is 0.03 lux (F1.2)
B/W modeÃHorizontal resolution, more than 520 TV linesÃPower supply: 24 V AC operation (VCC-4594P)
12 V DC operation (VCC-4592P)
ACCESSORIES1
Lens iris plug (4-pin) ..................................................................1 pc.
2
Clamping core A .......................................................................2 pc.
3
Clamping core B ........................................................................3 pc.
123
L53Z4/XE GB 2001, 5, 23English
 1 
						

							PRECAUTIONS
In case of problem
Do not use the camera if smoke or a strange odour comes from the
unit, or if it seems not to function correctly. Disconnect the power
cord immediately, and consult your dealer (or a Sanyo Authorized
Service Centre).Do not open or modify
Do not open the cabinet, as it may be dangerous and cause damage
to the unit. For internal settings and repairs, consult your dealer (or a
Sanyo Authorized Service Centre).Do not put objects inside the unit
Make sure that no metal objects or flammable substance get inside
the camera. If used with a foreign object inside, it could cause a fire,
short-circuits or damages.
If water or a liquid gets inside the camera, disconnect the power cord
immediately, and consult your dealer (or a Sanyo Authorized Service
Centre). Be careful to protect the camera from rain, sea water, etc.Be careful when handling the unit
To prevent damages, do not drop the camera or subject it to strong
shock or vibration.Install away from electric or magnetic fields
If installed close to a TV, radio transmitter, magnet, electric motor,
transformer, audio speakers the magnetic field they generate will
distort the image.
Protect from humidity and dust
To prevent damages to the camera, do not install it where there is
greasy smoke or steam, where the dampness may get too high, or
where there is a lot of dust.Protect from high temperatures
Do not install close to stoves, or other heat generating devices, such
as spotlights, etc., or where it could be subject to direct sunlight, as
that could cause deformation, discoloration or other damages.
Be careful when installing close to the ceiling, in a kitchen or boiler
room, as the temperature may raise to high levels.
Install where the temperature range will stay between Ä10ÆC and
50ÆC.
(no condensation)CleaningÃDirt can be removed from the cabinet by wiping it with a soft
cloth. To remove stains, wipe with a soft cloth moistened with a
soft detergent solution and wrung dry, then wipe dry with dry
soft cloth.ÃDo not use benzine, thinner or other chemical product on the
cabinet, as that may cause deformation and paint peeling. Before
using a chemical cloth, make sure to read all accompanying
instructions. Make sure that no plastic or rubber material comes
in contact with the cabinet for a long period of time, as that may
cause damage or paint peeling.
ENGLISH
L53Z4/XE GB 2001, 5, 23
2 
English 
						

							PARTS NAMES
1
Power indicator (POWER)
Comes on when the power to the camera is on.
2
Video output connector (VIDEO OUT: BNC type)
Connect this connector to a device such as a VCR or monitor with a VIDEO IN connector.
3
Manual colour/black and white setting terminal (CONTROL)ÃG (ground) terminalÃC (colour) terminalÃB (black and white) terminal
4
External sync composite video signal input connector (VBS IN: BNC type)
Connect to this connector the synchronizing signal output from a synchronizing signal device or the composite
signal of a video distributor.
5
Line phase adjustment volume (LINE PHASE) (VCC-4594P only)
When using two cameras or more, the image on the monitor may roll vertically when switching sources. This
rolling can be minimized by turning this volume.
6
Power input terminalÃVCC-4594P: 24 V AC input terminal (24 V AC, GND)ÃVCC-4592P: 12 V DC input terminal (12 V DC, NC, +, Ä)
7
Camera setup section (under the cover)
If due to installation conditions or environment the settings may need to be modified for best results (see
SETTINGS). 
To access the controls, loosen the cover fixing screw A, then remove the cover.
8
Lens iris output connector (LENS)
1
56
2
GC B
3
4
(VCC-4594P)
1
6
2
GC B
3
4
(VCC-4592P)
7
8A
L53Z4/XE GB 2001, 5, 23English
 3 
						

							PARTS NAMES
8
Flange-back lock screw
9
Lens mount cap
The cap is installed to protect the lens mount section.
Remove the lens mount cap before installing a lens (sold separately).
F
Flange-back adjustment lever (See page 6)
G
Camera installation bracket
The bracket can be fixed at the top or bottom of the camera. When fixing the bracket, be sure to use the
longer screws and install the shorter screws on the opposite side to seal the openings.1
Shorter screws: M3 x 4
2
Longer screws: M3 x 6
3
Camera mounting screw hole: 1/4-20 UNC
CAUTION:When installing the camera support, select a location that can support the total weight of the
camera and accessories.
12
3
2
1
G98
F
L53Z4/XE GB 2001, 5, 23
4 
English 
						

							CONCERNING AUTO-IRIS LENSES
DC type auto-iris lens
A lens without amplifier circuit that operates only on a DC power source. In general, this type of lens is
referred to as DC type coil lens or DC type non-amplifier lens.
(Set the A.I. LENS switch to the DC position.)VIDEO type auto-iris lens
A lens with amplifier circuit that operates on video signal and DC power source. In general, this type of lens is
referred to as EE amplifier type lens.
ALC and LEVEL volume level controls are available on the lens for iris adjustments.
(Set the A.I. LENS switch to the VIDEO position.)Compatible auto-iris lenses
1/3 inch Sanyo DC type lens VIDEO type lens
VCL-CS8LY: Standard angle, f= 8 mm Standard angle, f= 9 mm
VCL-CS4LY: Wide angle, f= 4 mm Telephoto angle, f= 12 mm
VCL-CS2LY: Ultra-wide angle, f= 2.8 mm More telephoto angle, f= 16 mm
If using a VIDEO type auto-iris lensÃSet the ALC and LEVEL controls on the lens to adjust the iris. Normally the ALC volume should be turned
all the way to Av (Average).ÃDepending on the type of lens used, the lens may not perform properly. In such a case, adjust the LEVEL
volume on the lens casing to correct.
DC
VIDEOA. I.
LENS
L53Z4/XE GB 2001, 5, 23English
 5 
						

							FLANGE-BACK ADJUSTMENT
If the pick-up surface is not correctly positioned with relation to the lens focal point, the picture will be out of
focus (in particular when using auto-iris power zoom lenses, sold separately). If that is the case, adjust the
flange-back position as described below.1
Using a + screwdriver, loosen the flange-back lock screw (M2:+).
2
Set the zoom lens to the maximum telephoto position, set the focus using the focus ring on the lens.
3
Set the zoom lens to the maximum wide angle position, set the focus using the flange-back adjustment
lever.
4
Repeat steps 2 and 3, until the image stays in focus when changing from a telephoto shot to a wide angle
shot.
When the setting is complete, tighten the flange-back lock screw.
Note:
When flange-back lock screw is completely tighten it will protrude slightly as shown in the illustration (Fig. 1).
Do not tighten the screw further.
Fig. 1
Flange-back lock screw2
3
1, 4
L53Z4/XE GB 2001, 5, 23
6 
English 
						

							MOUNTING THE LENS
Please use a DC type auto-iris lens (sold separately).
Checking the lens mountDo not use a lens if length ©Lª is more than 5 mm. If not, that may damage the camera and prevent
proper installation.
1
Remove the lens mount cap from the camera.
2
Install the auto-iris lens.
CS mount type lens
Carefully align the lens mount with the camera opening, then turn the lens slowly to install it.
C mount type lens
To allow for flange-back adjustment, install the C-mount adaptor (option) on the lens mount, then
carefully align the lens mount with the camera opening and turn the lens slowly to install it.
3
Connect the lens plug to the lens iris output connector (LENS) on the side of the camera.
When using lenses from other makers, the plug shape may not correspond to the terminal on the camera.
In such a case, remove the original plug and using a soldering iron, connect the supplied lens iris plug
according to the diagram. (Refer to page 8.)
NOTE:When using an auto-iris lens, the supplied clamping core (B) must be installed on the lens wire, in
order to prevent electromagnetic interference to the other devices connected.
L
1
C mount type lens
2
CS mount
type lens
2 3
L53Z4/XE GB 2001, 5, 23English
 7 
						

							MOUNTING THE LENS
Rewiring the lens cable in the lens iris plug
1Prepare the lens cable.
Cut the cable at the plug, then remove approx. 8 mm of the cable sheath and strip about 2 mm from each wire.
2
Install the lens iris plug.
Solder the cable to the pins following the correct pin layout (refer to the table and illustrations), then close
the plug cover.
Pin layout
DC type lenses VIDEO type lenses
1
Brake coil (Ä) +12 V DC (50 mA max.)
2
Brake coil (+) Not used
3
Drive coil (+) Video output (1.0 Vp-p, high impedance)
4
Drive coil (Ä) Ground (for video signal and DC power)
1
2
43 1
43 1 22
L53Z4/XE GB 2001, 5, 23
8 
English 
						

							CONNECTIONS(VCC-4594P only)
Basic connection for monitoring or recording
The peripheral devices (VCR, monitor, lens, etc.) and cables are
sold separately.1
Make the video signal connection between the camera and
the monitor or time lapse VCR.
2
Connect to 24 V AC UL listed class 2 power supply (sold
separately).CAUTION:ÃTo prevent camera and/or power supply failure, pay close attention
to polarity when making the connections.ÃTo prevent fire hazard any UL listed wire rated VW-1, should be used
for the 24 V AC cable input terminal.
2A:
When using this unit, the supplied clamping core (A or B) must be
installed on the power cord and BNC cable, in order to prevent
electromagnetic interference to the other devices connected.
3
Insert the plug of this power cord into a wall outlet.
The POWER indicator (A) will light. Adjust the picture on the
monitor using the Brightness and Contrast controls.Coaxial cable type and maximum lengthÃCable type RG-59U (3C-2V), 250 m maximum.ÃCable type RG-6U (5C-2V), 500 m maximum.ÃCable type RG-11U (7C-2V), 600 m maximum.
CAUTION:ÃThe RG-59U type cable should not be run through electrical
conduits or through the air.ÃUsing CCTV/Video-grade coaxial cable.
(Video signal connections)
       : VIDEO IN
       : VIDEO OUT
(A)
1
2A
2A
2
2A
3
(A)
(A)
(B)
24 V AC GND 24 V AC
2A
(B)
L53Z4/XE GB 2001, 5, 23English
 9