Sanyo Projector Plv Hd150 User Manual

							31
DISPLAY ADJUST
Press SELECT button to show information of computer selected.
Current mode
Adjusts clamp position. When image has a dark bar(s), try this
adjustment.
Clamp
Press SELECT button at Current
mode icon to show  information of
computer connected.
Current mode
Press SELECT button at this icon
to display previous items.
Reset
Store
Closes DISPLAY ADJUST MENU.
Quit
Other icons operates as follows.
3
To store adjustment parameters, move a red frame pointer to
Store icon and then press SELECT button.  Move a red arrow
pointer to any of Mode 1 to 20 that you want to store and then
press SELECT button.
Reset all adjust parameters on adjustment dialog box to previous
figure.
Mode free
To store adjustment data.
To clear adjustment data.
To clear adjustment parameters previously set, move a red
frame pointer to Mode free icon and then SELECT button.  Move
a red arrow pointer to Mode that you want to clear and then
press SELECT button.
Mode free icon
Store icon
Vacant Mode
Shows values of “Total dots”
“Display area H” and “Display
area V”.Terminal board and
System of input signal.
Press POINT LEFT/RIGHT
buttons to display right page.
Press POINT UP/DOWN buttons
to display next/previous page.
Close this
dialog box.
This Mode has parameters
being stored. Shows values of scale and position
of “Aspect H” and “Aspect V” . 
						

							32
IMAGE ADJUST MENU
Move a red frame pointer to
item to be selected and then
press SELECT button.IMAGE ADJUST
Menu icon
IMAGE ADJUSTMENTS
Press MENU button and ON-SCREEN MENU will appear.  Press
POINT LEFT/RIGHT button to move a red frame pointer to
IMAGE ADJUST Menu icon.1
3Press POINT UP/DOWN button to move a red arrow to level that
you want to set and then press SELECT button.
Normal picture level preset on this projector for AV mode.
Standard (AV)
Picture level with improved halftone for graphics.
Real
Normal picture level preset on this projector for PC mode.
Standard (PC)
Picture level adjusted for picture with fine tone.
Cinema
User preset picture adjustment in IMAGE ADJUST Menu (P33-36).
IMAGE 1~10
IMAGE LEVEL SELECT (DIRECT)
Select image level among Standard (AV), Cinema, Standard (PC),
Real and Image 1 ~ Image 10 by pressing IMAGE button on Side
Control or on Remote Control Unit.
Select image level Image 1 ~ Image 10 by pressing IMAGE 1 ~
IMAGE 10 buttons on Remote Control Unit.IMAGE button
Standard (AV)
Cinema
Standard (PC)
Real
Image 1
Image 10
Normal picture level preset on this projector for AV mode.
Standard (AV)
Picture level adjusted for picture with fine tone.
Cinema
IMAGE 1 ~ IMAGE 10  
buttons
Image 1
Image 10
Normal picture level preset on this projector for PC mode.
Standard (PC)
Picture level with improved halftone for graphics.
Real
User preset picture adjustment in IMAGE ADJUST Menu (P33-36).
IMAGE 1~10
IMAGE LEVEL SELECT (MENU)
2Press POINT UP/DOWN button to move a red frame pointer to
image icon and then press SELECT button.
DISPLAY ADJUST 
						

							33
DISPLAY ADJUST
Press MENU button and ON-SCREEN MENU will appear.  Press
POINT LEFT/RIGHT buttons to move a red frame pointer to
IMAGE ADJUST Menu icon.1
2Press POINT UP/DOWN button to move a red frame pointer to
item that you want to adjust and then press SELECT button.
Level of each item is displayed.  Adjust each level by pressing
POINT LEFT/RIGHT button(s).
IMAGE ADJUST MENU
Press POINT LEFT button to decrease contrast, and POINT RIGHT
button to increase contrast.  (From 0 to 63.)
Press POINT LEFT button to adjust image darker, and POINT
RIGHT button to adjust brighter.  (From 0 to 63.)
Contrast
Brightness
Press POINT LEFT button to lighten color, and POINT RIGHT button
to deeper color.  (From 0 to 63.)
Press POINT LEFT button or POINT RIGHT button to obtain proper
color.  (From 0 to 63.)
Color
Tint
Press POINT LEFT/RIGHT buttons
to adjust value.
Move a red frame pointer to
item to be selected and then
press SELECT button.IMAGE ADJUST
Menu icon
Press SELECT button at this icon
to display previous items.
Press POINT LEFT/RIGHT buttons
to adjust value.
Press SELECT button at this icon
to display next items.
Press POINT LEFT button to soften the image, and POINT RIGHT
button to sharpen the image.  (From 0 to 15.)
Sharpness
Press POINT LEFT button to lighten red tone and POINT RIGHT
button to deeper tone.  (From 0 to 63.)
White balance (Red)
Press POINT LEFT button to lighten green tone and POINT RIGHT
button to deeper tone.  (From 0 to 63.)
White balance (Green)
Press POINT LEFT button to lighten blue tone and POINT RIGHT
button to deeper tone.  (From 0 to 63.)
White balance (Blue)
Color temp.
Press either POINT LEFT button or POINT RIGHT button to Color
temp. level that you want to select. (XLow, Low, Mid or High) 
Press either POINT LEFT button or POINT RIGHT button to obtain
better balance of contrast.  (From 0 to 15.)
Gamma
Press either POINT LEFT button or POINT RIGHT button to enhance
the detail of the image.  (From 0 to 15.)
Detail enhancer
Press SELECT button at this icon
to display next items.
IMAGE LEVEL ADJUSTMENTS 
						

							34
Press POINT LEFT/RIGHT button(s) to change progressive scan
mode.  Dialog box display is changed to “Off” and progressive scan
mode to off. Press POINT LEFT/RIGHT button(s) again, progressive
scan mode to on. 
Press POINT LEFT/RIGHT button(s) to change noise reduction
mode.  Dialog box display is changed to “Off”, “L1”, “L2” or “L3” to
reduce noise (rough parts) of  image.
Off ·······Noise reduction OFF position.
L1 ········ Noise reduction LEVEL 1 position.
L2 ········ Noise reduction LEVEL 2 position.
L3 ········ Noise reduction LEVEL 3 position.
Noise reduction
Progressive scan
Press POINT LEFT/RIGHT buttons
to change position.
Press SELECT button at this icon
to display first items.
Auto picture control
Press either POINT LEFT button or POINT RIGHT button to Auto
picture control position that you want to select . (Off, L1 or L2)
Off ·······Auto picture control OFF position.
L1 ········ Auto picture control LEVEL 1 position.
L2 ········ Auto picture control LEVEL 2 position.
Auto lamp control
The projector reduce the brightness and set into the low power
consumption mode. When this function is “On”, the brightness is
adjusted automatically to a level that is suitable for the screen.
Press SELECT button at this icon
to display previous items.
DISPLAY ADJUST
Color Management
The Color management function can be used to adjust the level,
phase and gamma of the selected display colors on the screen, and
to replace these colors with other colors if required.
The projector lets you replace up to eight colors for each image.
1Press the POINT UP/DOWN button to move the red frame point-
er to COLOR MANAGEMENT, and then press the SELECT
button. The COLOR MANAGEMENT menu will appear and
pointer mode will be enabled. The image that was being project-
ed when the button was pressed will be paused, and the COLOR
MANAGEMENT POINTER will appear.
Use the POINT buttons to move the pointer to a section of the
paused image that contains the color that you would like to
adjust, and then press the SELECT button. The mode will
change to COLOR SELECTION mode, and the color in the cen-
ter of the pointer will be selected and adjustment will be possi-
ble.2
Use the POINT buttons to adjust the level and phase of the
color, and then press the SELECT button to confirm the setting.
Next, use the POINT buttons to adjust the gamma correction for
the color, and then press the SELECT button to accept the set-
ting. When the SELECT button is pressed, the mode will change
to LIST mode.3
COLOR 
MANAGEMENT
POINTER
POINTER MODE    
						

							35
DISPLAY ADJUST
To move the red frame pointer to MENU, and then press the
SELECT button. The message OK? is displayed. Move the
pointer to 
[Yes] and then press SELECT button.The COLOR
MANAGEMENT menu will be exited and the display will return
to the IMAGE ADJUST menu. (At this time, the image will stop
being paused and normal projection will resume.) After chang-
ing the COLOR MANAGEMENT settings, use the IMAGE
ADJUST menu to store the changed settings.
The check mark will be cleared and the effect of the setting adjustment
for that line on the projected images will be momentarily canceled.
4
CANCEL
COLOR SELECTION MODE
The mode will return to the pointer mode (even if you press the
MENU key on the projector or the remote control). (You will need to
reselect and re-adjust the color in this case.)
QUIT
The COLOR MANAGEMENT menu will be exited and the display will
return to the normal projection screen, but any settings that have
been changed will not be stored. To store the changed settings, be
sure to select LIST using the POINT buttons and change to the
next mode (LIST mode).
LIST MODE
The mode will return to COLOR SELECTION mode so that you can
re-adjust the setting for the color in that line. This option is not avail-
able if the check mark has been cleared by the operation immediate-
ly above.)
COLOR PALETTE
The setting adjustment for the color in that line will be canceled.
DEL
ALL DEL
The setting adjustment for the colors in all lines will be canceled.
COLOR M.
The mode will return to POINTER mode.
COLOR SELECTION
MODE
CANCELLISTQUIT
Level and phase
adjustment palette.Gamma
adjustment palette.
LIST MODECOLOR PALETTE
DEL
ALL DELCOLOR M.MENU 
						

							36
DISPLAY ADJUST
Reset all adjustment to previous figure.
Reset
Store
Closes IMAGE MENU.
Quit
Other icons operates as follows.
To store manually preset image, move a red frame pointer to Store
icon and press SELECT button. Image Level Menu will appear.
Move a red frame pointer to Image 1 to 10 where you want to set and
then press SELECT button. 
Message OK? is displayed. Move
pointer to [Yes] and then press SELECT button.
Image Level Menu
Move a red frame pointer to
any of Image 1 to 10 where you
want to set  and then press
SELECT button.
Store icon
Press SELECT button at this
icon to store the adjustment.
Gamma balance
The Gamma balance function can be used to adjust the R, G, B
Gamma balance of the screen.
1Press the POINT UP/DOWN button to move the red frame point-
er to Gamma balance, and then press the SELECT button. The
Gamma balance adjust menu will appear.
2Use the POINT LEFT/RIGHT buttons to move the adjust point (R
P1, R P2, R P3, G P1, G P2, G P3, B P1, B P2, B P3) and press
the POINT UP/DOWN button to adjust value.
Reset
Quit
Press the POINT LEFT/RIGHT button to move the red frame pointer to
Quit, and then press the SELECT button. The Gamma balance
adjust menu will be exited.
Press the POINT LEFT/RIGHT button to move the red frame pointer to
Reset, and then press the SELECT button. Reset the adjustment
value to previous figure.    
						

							37
SETTING
SETTING MENU
Press MENU button and ON-SCREEN MENU will appear.  Press
POINT LEFT/RIGHT button(s) to move a red-frame pointer to
SETTING icon.1
2
Language
Press POINT DOWN button to move a red-frame pointer to item
that you want to set and then press 
SELECT button.  Setting
dialog box appears.
When pressing SELECT
button at Language,
Language Menu appears.
SETTING MENU
Language used in ON-SCREEN MENU is selectable from among
English, German, French, Italian, Spanish, Portuguese, Dutch,
Swedish, Russian, Chinese, Korean and Japanese.
SETTING Menu icon
Set a red frame
pointer to item and
press SELECT
button.
Lamp Mode
This Projector is equipped with 4 Projection Lamps and a number of
using lamps can be switched to 4 lamps or 2 lamps.  Using 2 lamps
maintain life of Projection Lamps.  
To change over Lamp Mode
1.  Press MENU button and ON-SCREEN MENU will appear.  Press
POINT LEFT/RIGHT buttons to select SETTING and press
SELECT button.  Setting dialog box appears.
2. Press POINT DOWN button to move a red frame pointer to
“Lamp mode”.  Set 4 lamps mode or 2 lamps mode by
pressing POINT LEFT/RIGHT button(s).  When Lamp Mode is
set from 4 lamps mode to 2 lamps mode image becomes little
darker.  When Lamp Mode is set from 2 lamps mode to 4
lamps mode image become brighter gradually.
Display
This function decides whether to display On-Screen Displays.
On  ···Shows all the On-Screen Displays.
Off  ···Sets On-Screen Displays disappeared except;
ON-SCREEN MENU 
“Power off?” message
P-TIMER
“No signal” message 
“Wait a moment” message  
Blue back
When this function is “On,” this projector will produce a blue image
instead of the video noise on the screen when any input source is
unplugged or turned off.
Move a pointer to item
and then press POINT
LEFT/RIGHT button(s).Optional Control NumberRefer to page 11.
Menu size
This function decides to display On-Screen Displays size.
Normal  ··· Shows normal size the On-Screen Displays.
Double  ··· Shows double size the On-Screen Displays. 
						

							38
SETTING
Logo
When this function is “On,” projector displays logo when starting up.
Menu position
Rear
When this function is “On,” picture is left / right reversed.  This
function is used to project the image to a rear projection screen.
Rear function
Press SELECT button at this icon
to display next items.
Press SELECT button at this icon
to display previous items.
This function is used to adjust the on-screen menu display position.
When a SELECT button is pressed, the adjustment screen is
displayed (arrows appear). Use the POINT UP/DOWN/LEFT/RIGHT
button(s) to adjust the position. After making the adjustment, press a
SELECT button to return to the Menu screen. 
						

							39
SETTING
On start
When this function is “On,” projector is automatically turned on just
by connecting AC Power cord to a wall outlet.
Note ; B e  sure to turn projector off properly (refer to section
“TURNING OFF PROJECTOR” on P22).  If projector is turned
off in wrong steps, On Start function does not operate
properly.
Power management
Time left until Lamp off.
Remote control
This projector has eight different remote control codes; the factory-
set normal code (Code 1) and the other seven codes (Code 2 to
Code 8).  This switching function prevents remote control operation
mixture (jam) when operating several projectors or video equipment
together.  
For example operating projector in “Code 7,”  both projector and
Remote Control Unit must be switched to “Code 7.”  
To change the code of Projector;
To change the Remote control code of the projector used in ON-
SCREEN MENU is selectable from Code 1 to Code 8.
To change the code of the Remote Control Unit;
While pressing the MENU button, press the IMAGE button number of
times corresponding to each remote control code number. (Refer to
P19.)
When pressing SELECT button at
Remote control, Remote control
code Menu appears.
This projector is equipped with a power management function. When the input signal is interrupted and any button is not
pressed for 30 seconds or more, the power management function operates in order to reduce power consumption and
conserve lamp operating time. The factory default settings for power management are Ready and 5 Min.
The power management function is canceled.
When a SELECT button is pressed,
the adjustment screen is displayed.
Use the POINT LEFT/RIGHT button(s)
to select the power management
function mode (Off, Ready or Shut
down).
Use the POINT DOWN button to move
the pointer to the time setting, and then
use the POINT LEFT/RIGHT button(s)
to set the time (1 minute to 30
minutes). 
If Shut down is selected
If Off is selected
If Ready is selected
OPERATION
1) If the input signal is interrupted and any button is not pressed for 30 seconds or more, the message No signal and the
timer display appears on the screen. Then the count-down starts for the time being set.
2) When the set time is elapsed, the lamp will be switched off
and lamp cooling starts. The READY indicator will be
switched off while the lamp cooling is in progress, and the
projector cannot be operated during this time.
3) When the lamp cooling is completed, the READY indicator
starts flashing to notify the operator that power
management mode is active. In this condition, the lamp
will turn on and images will be projected if a signal starts
being input or the projector is operated.
2) When the set time is elapsed, the lamp will be switched off
and lamp cooling starts. The READY indicator will be
switched off while the lamp cooling is in progress, and the
projector cannot be operated during this time.
3) When the lamp cooling is completed, the power switches
off. 
						

							40
SETTING
Lamp counter reset
Key lock
Factory default
Press POINT UP/DOWN button to move a red frame pointer to
“Factory default” and then press 
SELECT button.  The message
Return to Factory default? is displayed.  Move the pointer to [Yes]
and then press SELECT button.
Another confirmation dialog box appears and select [Yes] 
and then
press SELECT button. Return the projector to Factory default.
This function returns all setting values except for the lamp counter to
the factory default settings.
This function locks the operation of the projectors control panel and
the remote control.
This locks operation of the projectors control panel.
This locks operation of the remote control.
This cancels the Key lock function.
If the projectors control panel accidentally becomes locked and you
do not have the remote control nearby, turn the MAIN ON/OFF
switch to OFF. And then while pressing a SELECT button, return the
MAIN ON/OFF switch to ON again. This will cancel the projectors
control panel lock.
Be sure to reset Lamp Counter when Lamp Assembly is replaced.  When Lamp Replace Counter is reset, LAMP
REPLACE indicator stops lighting.
Turn projector on, press MENU button and ON-SCREEN
MENU will appear.  Press POINT LEFT/RIGHT button(s) to
move a red frame pointer to SETTING Menu icon.1
Press POINT DOWN button to move a red frame pointer to
“Lamp counter reset” and then press 
SELECT button.2
Do not reset Lamp Replace Counter except after Projection lamp is
replaced.
Another confirmation dialog box appears and select [Yes] to
reset Lamp Replace Counter.4
Move arrow to replaced lamp number (Lamp 1, Lamp 2, Lamp 3
or Lamp 4) and then press 
SELECT button.  Message Lamp
replace counter Reset? is displayed. Move pointer to [Yes] and
then press SELECT button.3
NOTE:Be sure to reset correct lamp number otherwise LAMP
REPLACE indicator continues lighting.
Closes SETTING MENU.
Quit