Sanyo Projector Plc Xw57 User Manual

							Check the indicators for projector condition.
Indicators and Projector Condition
The projector is off. (The AC power cord is unplugged.)
The  projector  is  preparing  for  stand-by  or  the  projection 
lamp  is  being  cooled  down.    The  projector  cannot  be 
turned on until cooling is completed.
The  temperature  inside  the  projector  is  abnormally  high. 
The  projector  cannot  be  turned  on.    When  the  projector 
is  cooled  down  enough  and  the  temperature  returns 
t o  n o r m a l ,  t h e  P O W E R  i n d i c a t o r  l i g h t s  r e d  a n d  t h e 
projector  can  be  turned  on.  (The  WARNING  indicator 
keeps blinking.)  Check and clean the air filters.
Projector Condition
The  projector  is  ready  to  be  turned  on  with  the  POWER 
O N / S TA N D - B Y  b u t t o n  o n  t h e  t o p  c o n t r o l  o r  o n  t h e 
remote control.
POWER
red/green
Indicators
LAMP 
REPLACE yellowWARNING  red
The  projector  detects  an  abnormal  condition  and  cannot 
be  turned  on.    Unplug  the  AC  power  cord  and  plug  it 
again  to  turn  on  the  projector.    If  the  projector  is  turned 
off again, disconnect the AC power cord and contact the 
dealer  or  the  service  center.  Do  not  leave  the  projector 
on.  It may cause an electric shock or fire hazard.





The projector is operating normally.
The projector is in the Power management mode. 


The  projector  has  been  cooled  down  enough  and  the 
temperature  returns  to  normal.    When  turning  on  the 
projector, the WARNING indicator stops blinking.  Check 
and clean the air filters.
• • • green• • • red• • • off
• • • blinks green
  When the life of the projection lamp draws to an end, the LAMP REPLACE indicator lights yellow.   
    When this indicator lights yellow, replace the projection lamp with a new one promptly.  Reset the  
    lamp replacement counter after replacing the lamp.  See pages 54 and\
 55.
• • • blinks red
Appendix
61 
						

							Appendix
6
Compatible Computer Specifications
Basically  this  projector  can  accept  the  signal  from  all  computers  with  the  V,  H-Frequency  below 
mentioned and less than 110 MHz of Dot Clock.  When selecting these modes, PC adjustment can be limited.
MAC LC13640 x 48034.9766.60MAC 13640 x 48035.0066.67
MAC 1683 x 6449.774.55
MAC 19104 x 76860.475.08
SVGA 1800 x 60035.15656.5SVGA 800 x 60037.8860.3SVGA 3800 x 60046.87575.00SVGA 4800 x 60053.67485.06SVGA 5800 x 60048.087.19SVGA 6800 x 60037.9061.03SVGA 7800 x 60034.5055.38SVGA 8800 x 60038.0060.51SVGA 9800 x 60038.6060.31
SVGA 11800 x 60038.0060.51
XGA 10104 x 768XGA 11104 x 768XGA 1104 x 768XGA 13104 x 768
6.0477.07
XGA 14104 x 768
61.0075.70
XGA 15104 x 768
35.586.96
(Interlace)
46.9058.0
XGA 8104 x 768
47.0058.30
XGA 9104 x 768
58.037.00
63.4879.3536.0087.17
(Interlace)
SXGA 7180 x 104
SXGA 10180 x 960
81.1376.107
60.0060.00
XGA 1104 x 768
XGA 4104 x 768
48.3660.00
XGA 6104 x 768XGA 7104 x 768
56.47670.07
48.5060.044.0054.58
SXGA 8180 x 104SXGA 9180 x 10463.9860.079.97675.05
XGA 5104 x 76860.3174.9
VGA 7640 x 48043.6985.00
575i––––––––15.6550.00
(Interlace)480i––––––––15.73460.00
(Interlace)
SXGA 1115 x 90071.4075.60SXGA 11115 x 90061.065.0
SVGA 10800 x 6003.7051.09
SXGA 13180 x 10450.0086.00
(Interlace)
ON-SCREEN 
DISPLA yRESOLUTIONH-Freq .
(kHz)V-Freq . (Hz)
VGA 1640 x 48031.4759.88VGA 70 x 40031.4770.09VGA 3640 x 40031.4770.09VGA 4640 x 48037.8674.38VGA 5640 x 48037.867.81VGA 6640 x 48037.5075.00
SXGA 1115 x 86464.070.40
ON-SCREEN  DISPLA yRESOLUTIONH-Freq .
(kHz)V-Freq . (Hz)
SXGA 4180 x 10463.3459.98SXGA 5180 x 104SXGA 6180 x 10463.7460.0171.6967.19
SXGA 180 x 1046.5058.60SXGA 3180 x 10463.9060.00
XGA 104 x 76868.67784.997XGA 3104 x 76860.0375.03
SXGA 18180 x 10446.4386.70
(Interlace)
SXGA 19180 x 10463.7960.18
SXGA 14180 x 104SXGA 15180 x 104SXGA 16180 x 104SXGA 17115 x 900
50.0094.00
(Interlace)
63.3760.0176.977.00
UXGA 41600 x 10093.7575.00
UXGA 11600 x 100UXGA 1600 x 100UXGA 31600 x 100
75.0060.0081.565.0087.570.00
WXGA 6180 x 768WXGA 7180 x 768WXGA 8
47.77659.87060.8974.89368.63384.837180 x 768
61.8566.00
MAC180 x 96075.0075.08MAC180 x 104480p––––––––575p––––––––
80.0075.0831.4759.88
1080i––––––––
31.550.00
33.7560.00
(Interlace)
70p––––––––1035i––––––––45.0060.0033.7560.00
(Interlace)
1080i––––––––8.1550.00
(Interlace)
SXGA+ 11400 x 105063.97060.190
MAC1115 x 87068.6875.06
WXGA 1360 x 768WXGA 31376 x 768WXGA 41360 x 768
47.7060.0048.3660.0056.167.00
WXGA 11366 x 76848.3660.00
SXGA+ 1400 x 105063.35060.10SXGA+ 31400 x 105065.1059.900
SXGA 0180 x 10491.14685.04 
						

							Technical Specifications
Mechanical Information	 Projector	Type	 Multi-media	Projector	
	
Dimensions	(W	x	H	x	D)	 12.99"	x	3.15"	x	9.33"	(330	mm	x	80	mm	x	237	mm)	(Not	including	protrusion)	
	 Net	Weight	 6.4	lbs	(2.9	kg)	
	
Foot	 Adjustment	 0˚	to	10.0˚	
	
Panel Resolution	 LCD	Panel	System	 0.6"	TFT	Active	Matrix	type,	3	panels	
	
Panel	Resolution	 1,024	x	768	dots	
	
Number	of	Pixels	 2,359,296	(1,024	x	768	x	3	panels)	
	
Signal Compatibility	 Color	System	 PAL,	SECAM,	NTSC,	NTSC4.43,	PAL-M,	and	PAL-N	
	
High	Definition	 TV	Signal	 480i,	480p,	575i,	575p,	720p,	1035i,	and	1080i 	
	
Scanning	Frequency	 H-sync.	15	~	100	kHz,	V-sync.	50	~	100	Hz 	
	
Optical Information	 Projection	Image	Size	(Diagonal)	 Adjustable	from	40"	to	300"	
	
Projection	Lens	 F	1.65	~	1.83	lens	with	f	22.5	mm	~	27	mm	with	manual	zoom	and	
focus	
	
Throw	Distance	 	4.6'	-	43.3'	(1.4m	-	13.2m)	
	
Projection	Lamp	 200W		
	
Interface	 Video	Input	Jack	 RCA	Type	x	1		
	
Audio	Input	Jacks	 RCA	Type	x	2 	
	
Computer	In	1/	S-VIDEO	In	 Analog	RGB	(Mini	D-sub	15	pin)	 Terminal	x	1	
	/Component	In	 Computer	In	2/	Monitor	Out		 Analog	RGB	(Mini	D-sub	15	pin)	 Terminal	x	1,	In/Out	switchable
	Component/	Computer	 Audio	Input	Jack	 Mini	Jack	(stereo)	x	1	
	
Service	Port	Connector	 Mini	DIN	8	pin	x	1	
	
Audio	Output	Jack	 Mini	Jack	(stereo)	x	1	(Variable)	
	
Audio	 Internal	 Audio	Amp	 1.0	W	RMS	
	
Built-in	Speaker	 1	speaker,	ø1.1"	(28	mm)		
	
Power	 Voltage	and	Power	Consumption	 AC	100	~	120	V	(3.2A 	Max.	Ampere),	50/60	Hz	(The	U.S.A 	and	Canada)	
	
	 AC	200	~	240	
V	(1.6A 	Max.	Ampere),	50/60	Hz	(Continental 	Europe 	and 	The 	U.K.) 	
	
Operating Environment	 Operating	 Temperature	 41˚F	~	95˚F	(5˚C	~	35˚C)	
	
Storage	 Temperature	 14˚F	~	140˚F	(-10˚C	~	60˚C)	
	
Remote Control	 Battery	 AA	or	LR6	1.5	V	 ALKALINE	TYPE	x	2	
	
Operating	Range	 16.4'	(5	m)/±30˚	
	
Dimensions	 1.9"	(W)	x	0.87"	(H)	x	5.7"	(D)	(49	mm	x	22	mm	x	145.3	mm) 	
	
Net	Weight	 3.53	oz	(100	g)	(including	batteries)
63
Appendix 
						

							64
Appendix
Accessories Owner's Manual (CD-ROM)
  Quick Reference Guide  
  AC Power Cord  
  Remote Control and Batteries  
  VGA

 Cable  
  PIN Code Label
 
   Lens Cap with string
 
●  The specifications are subject to change without notice.● LCD  panels  are  manufactured  to  the  highest  possible  standards.    Even  though  99.99%  of 
the  pixels  are  effective,  a  tiny  fraction  of  the  pixels  (0.01%  or  less)  may  be  ineffective  by  the 
characteristics of the LCD panels.
    Model No.
S-VIDEO-VGA Cable  : POA-CA-VGAS
COMPONENT-VGA Cable  : POA-CA-COMPVGA 
SCART-VGA Cable  : POA-CA-SCAR
 T 
Laser Pointer Remote Control  : POA-RCKIT03 
Presentation Kit  : POA-RCKIT04 
Soft Carrying Case  : POA-CAC-VCL
  
 
The  parts  listed  below  are  optionally  available.    When  ordering  those  parts,  specify  the  item  and 
Model No. to the sales dealer.
Optional Parts 
						

							65
Appendix
Terminal: Mini DIN 8-PIN
SERVICE PORT CONNECTOR COMPUTER IN/S-VIDEO IN/COMPONENT IN/MONITOR OUT TERMINAL (ANALOG)
Terminal : Analog RGB (Mini D-sub 15 pin)
512341096781514131112
Configurations of Terminals
Red (R/Cr/S-C) Input/R Output
Ground (Horiz.sync.)
Green (G/Y/S-Y) Input/G Output
-----
Blue (B/Cb/---) Input/B Output
Ground (Red)
Ground (Green)
Ground (Blue)
1
5
2
4
3
6
7
8
5V / ---
Horiz. sync. Input/Output ，Composite H/V sync.Input
Ground (Vert.sync.)
DDC data / ---
Ground 
Vert. sync. Input/Output
DDC clock / ---
9
13
10
1
11
14
15
Serial
GND
R X D
-----
-----
-----
T X D
-----
4
1
3
2
5
6
7
-----8 
						

							66
Write  down  the  PIN  code  number  in  the  column  below  and  keep  it  with  this  manual  securely.  If  you 
forgot or lost the number and unable to operate the projector, contact the service station. 
PIN Code Number Memo
Factory default set No: 1  3 4*
*  Should  the  four-digit  number  be 
changed,  the  factory  set  number 
will be invalid.
PIN Code Lock No .
Logo PIN Code Lock No .
Factory default set No: 4 3  1*
While the projector is locked with the PIN code....
Put the label below (supplied) on in a prominent place of 
the projector's body while it is locked with a PIN code.
Appendix 
						

							67
Dimensions
Appendix
3.74(95)
13.0 (330)2.18(55.3)
9.33(237)
3.62(92)
3.94(100)
5.83(148)
4.72(120)
2.95(75) 5.31(135)
Screw Holes for Ceiling Mount
Screw: M4
Depth: 0.394(10.0)
Unit:inch(mm)
10°MAX
3.15(80)
Appendix 
						

							KM7ACSANyO Electric Co ., Ltd .