Sanyo Projector Plc Sw20ar User Manual

							41
APPENDIX
TROUBLESHOOTING
Before calling your dealer or service center for assistance, check the following:
1. Make sure you have connected a projector to your computer or video equipment as described in the section
CONNECTING PROJECTOR  on pages 11 ~ 13.
2. Check cable connection.  Verify that all computer, video and power cord are properly connected.
3. Verify that all power is switched on.
4. If a projector still does not produce an image, re-start your computer.
5. If an image still does not appear, unplug a projector from your computer and check your computer monitors display.  The
problem may be with your graphics controller rather than with a projector.  (When you reconnect a projector, be sure to
turn the computer and monitor off before you power up the projector.  Power the equipment back on in order of : Projector
and computer.)
6. If the problem still exists, check the following chart.
No power.Plug a projector into your AC outlet.
Make sure READY Indicator lights.
Wait 90 seconds after a projector is turned OFF before turning the projector back on.
NOTE :After pressing Power ON-OFF button to OFF, make sure a projector works as
follows:
1.  LAMP indicator lights bright and READY indicator turns off.
2. After 90 seconds, READY indicator lights green again and a projector may be
turned on by pressing Power ON-OFF button.
Check WARNING TEMP. indicator.  If the indicator flashes red, the projector cannot be
turned on.
(See TURNING ON/OFF PROJECTOR section on page 19.)
Check Projection Lamp.  (Refer to page 37.)
Image is out of
focus.Adjust focus of a projector.
Make sure a projection screen is at least 5.3’ (1.6m) from the projector.
Check Projection Lens to see if it needs cleaning.
NOTE : Moving a projector from a cool temperature location to a warm temperature location
may result in moisture condensation on Projection Lens.  In such an event, leave a
projector OFF and wait until condensation disappears.
Picture is Left/Right
reversed.Check Ceiling / Rear feature.  (See “SETTING” section on page 35.)
Problem:Try these Solutions
Picture is
Top/Bottom
reversed.Check Ceiling feature.  (See “SETTING” section on page 35.)
Some displays are
not seen during the
Operation.Check Display feature.(See “SETTING” section on page 35.)
No image.Check the connection between your computer or video equipment and a projector.
Check NO SHOW function.  (Refer to page 21.)
When turning a projector on, it takes about 30 seconds to display an image.
Check the system that you select is corresponding with your computer or video
equipment.
Make sure the temperature is not out of the Operating Temperature (5°C ~ 35°C).
No sound.Check audio cable connection from audio input source.
Adjust the audio source.
Press VOLUME (+) button.
Press MUTE button. 
						

							42
This symbol on the nameplate means the product is Listed by Underwriters
Laboratories Inc.  It is designed and manufactured to meet rigid U.L. safety standards
against risk of fire, casualty and electrical hazards.
APPENDIX
WARNING :
High voltages are used to operate this projector.  Do not attempt to open the cabinet.
If the problem still persists after following all operating instructions,
contact the sales dealer where you purchased the
projector or the service center.Give the model number and explain the difficulty.  We will advise you how to obtain service.
Remote Control Unit
does not work.Check the batteries.
Make sure nothing is between Infrared Remote Receiver and Remote Control Unit.
Make sure you are not too far from a projector when using Remote Control Unit.
Maximum operating range is 16.4’ (5m).
Make sure the code of Remote Control Unit is set to conform to projector.
(See “SETTING” section on page 35, 36.)
Problem:Try these Solutions 
						

							43
APPENDIX
TECHNICAL SPECIFICATIONS
0.7 TFT Active Matrix type, 3 panels
Multi-media Projector
6.2lbs (2.8 kg)
10.12 x 2.98 x 9.02 (257mm x 75.8mm x 229mm) (not including Adjustable Feet)
800 x 600 dots
1,440,000 (800 x 600 x 3 panels)
PAL, SECAM, NTSC, NTSC4.43, PAL-M and PAL-N
H-sync. 15 ~ 80 KHz, V-sync. 50 ~ 100 Hz
Adjustable from 34” to 200”
500 TV lines
1 speaker, ø1.1 (28mm) 
41 ˚F ~ 95 ˚F (5 ˚C ~ 35 ˚C)
14 ˚F ~ 140 ˚F (-10 ˚C ~ 60 ˚C)
Owner’s Manual
AC Power Cord
Remote Control Unit and Batteries
VGA Cable
Control Cable for PS/2 port
Carrying Bag
Lens Cover 
Projector Type
Net Weight
Dimensions (W x H x D)
Panel Resolution
Number of Pixels
Color System
Scanning Frequency
Projection Image size (Diagonal)
Horizontal Resolution
Built-in Speakers
Operating Temperature
Storage Temperature
Accessories
LCD Panel System
The specifications are subject to change without notice.
F 1.6 ~ 1.78 lens with f 28.7 mm ~ 34.5 mm with manual zoom and focus
5.3’ ~ 26.6’ (1.6 m ~ 8.1 m)
150 W
RCA Type  x 3 (Video/Y, Pb/Cb, Pr/Cr) and Mini DIN 4 pin x 1 (S-Video)
Projection Lens
Throw Distance
Projection Lamp
Video Input Jacks
Mini Jack (stereo)  x 1Audio Input Jacks
(VGA) HDB 15 Terminal x 1 
Mini Jack (stereo)  x 1
Mini DIN 8 pin x 1
Mini Jack (stereo)  x 1
1.0 W RMS
Computer Input Terminals
Computer Audio Input Jack
Control Port Connector
Audio Output Jacks
Internal Audio Amp
0˚ to 10.6˚Feet Adjustment
Power Source : AA, UM3 or R06 Type x 2
Operating Range : 16.4’ (5m) / ±30˚
Dimensions : 2.2” x 1.3” x 7.6” (55mm x 34mm x 192mm)
Net Weight : 0.36 lbs (165 g) (including batteries)
Laser Pointer : Class IILaser  
(Max. Output : 1mW / Wave length : 650±20nm)
Remote Control Unit
480i, 480p, 575i, 575p, 720p, 1035i, and 1080iHigh Definition TV Signal
USB Series B receptacle x 1USB Connector
AC 100 ~ 120 V (2.4 A  Max. Ampere), 50 / 60 Hz  (The U.S.A and Canada)
AC 200 ~ 240 V (1.2 A  Max. Ampere), 50 / 60 Hz  (Continental Europe)Voltage and 
Power Consumption
LCD panels are manufactured to the highest possible standards.  Even though 99.99% of the pixels are effective,  a
tiny fraction of the pixels (0.01% or less) may be ineffective by the characteristics of the LCD panels.  
						

							44
APPENDIX
CONFIGURATIONS OF TERMINALS
COMPUTER INPUT TERMINAL (ANALOG)
Terminal : HDB15-PIN 
512341096781514131112
Red Input
Ground (Horiz.sync.)
Green Input
Sense 2
Blue Input
Ground (Red)
Ground (Green)
Ground (Blue)
1
5
2
4
3
6
7
8
No Connect
Horiz. sync.
Ground (Vert.sync.)
Sense 1
Sense 0
Vert. sync.
Reserved
9
13
10
12
11
14
15
Pin Configuration
Terminal : Mini DIN 8-PIN
12
345876
Pin Configuration
CONTROL PORT CONNECTOR
-----
CLK
DATA
GND
-----
-----
GND
-----
R X D
-----
-----
GND
RTS / CTS
T X D
GND
GND
-----
ADB
-----
GND
-----
-----
-----
GND
PS/2SerialADB
1
2
3
4
5
6
7
8
Vcc
- Data
+ Data
Ground
1
2
3
4
USB CONNECTOR (Series B)
Pin Configuration
2
341
OPTIONAL PARTS
The parts listed below are optionally supplied.  When ordering those parts, give name and Type No. of it to the sales dealer.
Control Cable for Serial Port Type No.: POA-MCSRL
Control Cable for ADB Port Type No.: POA-MCMACMAC Adapter Type No.: POA-MACAP 
						

							45 
						

							46 
						

							47 
						

							Printed in Japan
Part No. 610 303 2498 (1AA6P1P3691-- MS8AA)
SANYO Electric Co., Ltd.