Sanyo Plc Xp20 Projector User Manual

							Problem:
No power.
Image is out of focus.
Try these Solutions:
Plug the projector into an AC outlet.
Turn the MAIN ON/OFF switch to ON.
Press the POWER ON/OFF switch to ON.
Be sure the READY INDICATOR light is ON.
Wait approximate 2 minutes after the projector is turned OFF before turning the
projector back on.
NOTE: After pressing the POWER ON/OFF button to OFF. The projector functions
as indicated.
1. The LAMP POWER indicator will light and the READY indicator will turn off.
2. After approximate 2 minutes, the READY indicator will light green again and the
projector may be turned on by pressing the POWER ON/OFF button.
Check temperature warning indicator. If the indicator flashes red, the projector
cannot be turned on.
(See BASIC OPERATION section on page 27).
Check the projection lamp.
Replace the lamp cover. (Check the interlock switch inside of the lamp cover.) 
Adjust the focus.
Make sure the projection screen is at least  4.6 (1.4 m) from the projector.
Check the projection lens to see if it needs cleaning.
NOTE:Moving the projector from a cool temperature location to a warm
temperature location may result in moisture condensation on the lens. In
such an event, leave the projector OFF and wait until condensation
disappears.
51
Before calling your dealer or service station for assistance, check the items below once again.
1. Make sure you have connected the projector to your equipment as described in section CONNECTING THE
PROJECTOR on pages 11 ~ 18.
2. Check cable connections. Verify that all computer, video and power cords are properly connected.
3. Verify that power is switched on.
4. If the projector still does not display an image, re-start the computer.
5. If the image still does not display, unplug the projector from the computer and check the computer monitors display.
The problem may be with your graphics controller rather than with the projector. (When you reconnect the projector,
remember to turn the computer and monitor off before you power up the projector. Power the equipment back up in
order of: Projector and computer)
6. If the problem still exists, check the following chart.
TROUBLESHOOTING
APPENDIX
Follow these steps to clean the projection lens:
1. Apply a non-abrasive camera lens cleaner to a soft, dry cleaning cloth.
Avoid using an excessive amount of cleaner.
Abrasive cleaners, solvents or other harsh chemicals might scratch the lens.
2. Lightly wipe the cleaning cloth over the lens.
3. When you are not using the projector, replace the lens cover.
CLEANING THE LENS 
						

							No sound.
52
Problem:
Check Ceiling feature.
(See OTHER FUNCTION SETTING section on pages 46 ~ 47).
Picture is L/R Reversed.Check Ceiling/Rear feature.
(See OTHER FUNCTION SETTING section on pages 46 ~ 47).
Picture is T/B inverted.
Check Display feature.
(See OTHER FUNCTION SETTING section on pages 46 ~ 47).Some displays are not seen
during the operation.
Check audio cable connection from audio input source.
Adjust audio source.
Press the VOLUME (+) button.
Press the MUTE button.
Check the batteries.
Make sure nothing is blocking between the remote control sensor and
remote control unit.
Make sure you are not too far from the projector when using the remote
control unit. Maximum operate range 16.4  (5 m).
Check the ALL-OFF switch on the Remote Control Unit is set to ON.
Check the transmitted signal mode from the remote control unit.
(See OTHER FUNCTION SETTING section on pages 46 ~ 47).Remote control unit does not
work.
Check the cable connection between the projector and the computer.
Check the mouse setting on your computer.
Turn on the projector before you turn on the computer.Wireless mouse function
does not work.
Try these Solutions:
APPENDIX
SERVICE
WARNING: High voltages are used to operate this
projector. Do not attempt to open the cabinet.
You can often correct operating problems yourself. If the
projector fails to work properly, see TROUBLESHOOTING
section on pages 51-52. To correct the failure, try the
Solutions.Sanyo Services is easily obtained. If after following all
operating instructions, you find that service is necessary,
contact the SFS Corporation in Los Angeles, or the store
where you purchased the unit.
Give the model number and explain the difficulty. We will
advise you how to obtain service. 
						

							53
TECHNICAL SPECIFICATIONS
Multi-media Projector
APPENDIX
100 ~ 120 VAC, 50/60 Hz
3.6 A (Max. Ampere)
5°C ~ 35°C (41°F ~ 95°F)
-10°C ~ 60°C (14°F ~ 140°F)
Projector Type
Dimensions (W x H x D)
Net Weight
LCD Panel System
Number of Pixels
Color System
Scanning Frequency
Projection Image Size (Diagonal) 
Projection Lens
Throw Distance
Projection Lamp
AV Input Jacks
Computer Audio Input Jacks
Computer Input Jacks
Built-in Speaker
Image Elevation Adjustment
Voltage
Power Consumption
Operating Temperature
Storage Temperature
Remote Control Transmitters
10.7 (272 mm) x 5.7 (145.5 mm) x 16.2 (412.5 mm)
15.2 Ibs (6.9 kg)
1.3 TFT Active Matrix type  x 3 panels
2,359,296 {786,432 (1,024 x 768) x 3}
6 color system (PAL, SECAM, NTSC, NTSC4.43, PAL-M and PAL-N)
H-sync. 15 ~ 100 KHz, V-sync. 50 ~ 100 Hz
Adjustable from 31 to 400
F1.8 ~ 2.1 lens with f=48.4 mm ~ 62.8 mm Motor zoom and focus
4.6 (1.4 m) ~ 47.3 (14.4 m)
200 watt type
RCA Type 3 x 2 sets (Video, Audio R and L), (Y, Cb/Pb, Cr/Pr)
and DIN 4 pin (S-Video) x 1 
Mini Stereo Type  x 2 
Computer Output Jack
Other Jack(VGA) HDB 15 Terminal
EXT. Speaker Jack (Stereo) x 1(VGA) HDB 15 Terminal x 2, DIN 8 pin (Control port) x 2
INT. SP. Stereo (R and L), 2 watt RMS (T.H.D.10%)
Up to 6 °
Wireless Remote Control with Laser Beam (Class Laser)
Max. Output 1mW/Wave Length 650 ± 20nm, batteries (2) AA type.
Horizontal Resolution800 TV lines
This symbol on the nameplate means the product is Listed by Underwriters
Laboratories Inc.  It is designed and manufactured to meet rigid U.L. safety
standards against risk of fire, casualty and electrical hazards. 
						

							Printed in Japan
Part No. 610 282 3066 (1AA6P1P2087-- MH6A)21605 Plummer Street,
Chatsworth, California 91311
SANYO INDUSTRIAL VIDEO
LCD PROJECTOR LIMITED WARRANTY
In order to obtain warranty service, the product must be delivered to and picked up from an Authorized Sanyo Factory Service
Center at the users expense, unless specifically stated otherwise in this warranty. The names and addresses of Authorized Sanyo
Service Centers may be obtained  by calling the toll-free number listed below.
OBLIGATIONS
For product operation, authorized service center referral, service assistance or problem resolution, call
CUSTOMER INFORMATION 1-800-421-5013
Weekdays 8:00 AM - 5:00 PM Pacific Time
For accessories and/or parts not available from an authorized dealer, call
PARTS ORDER INFORMATION 1-800-726-9662
Weekdays 8:00 AM - 5:00 PM Pacific Time
THIS WARRANTY IS VALID ONLY ON SANYO PRODUCTS PURCHASED OR RENTED AND USED IN THE UNITED STATES
OF AMERICA, EXCLUDING ALL U.S. TERRITORIES AND PROTECTORATES, FOR INDUSTRIAL PROFESSIONAL OR
COMMERCIAL PURPOSES.THIS WARRANTY APPLIES ONLY TO THE ORIGINAL RETAIL USER. THE ORIGINAL DATED
BILL OF SALE, SALES SLIP OR RENTAL AGREEMENT MUST BE SUBMITTED TO THE AUTHORIZED SANYO SERVICE
CENTER AT THE TIME WARRANTY SERVICE IS REQUESTED.
Subject to the OBLIGATIONS above and EXCLUSIONS below, SANYO FISHER COMPANY (SFC) warrants this SANYO product
against defects in materials and workmanship for periods of LABOR and PARTS specified below. SFC will repair or replace (at its
option) the product and any of its parts which fail to conform to this warranty. The warranty period commences on the date the
product was first purchased or rented at retail.
EXCLUSIONS
This warranty does not cover (A) the adjustment of customer-operated controls as explained in the appropriate models instruction
manual, or (B) the repair of any product whose serial number has been altered, defaced or removed.
This warranty shall not apply to the cabinet or cosmetic parts, knobs or batteries or routine maintenance.
This warranty does not apply to uncrating, setup, installation, removal of the product for repair or reinstallation of the product after
repair.
This warranty does not apply to repairs or replacements necessitated by any cause beyond the control of SFC including, but not
limited to, any malfunction, defect or failure caused by or resulting from unauthorized service or parts, improper maintenance,
operation contrary to furnished instructions, shipping or transit accidents, modification or repair by the user, abuse, misuse,
neglect, accident, incorrect power line voltage, fire, flood or other Acts of God, or normal wear and tear.
The foregoing is in lieu of all other expressed warranties and SFC does not assume or authorize any party to assume for it any
other obligation or liability.
SFC DISCLAIMS ALL WARRANTIES WHICH MAY BE IMPLIED BY LAW (INCLUDING THE WARRANTIES OF
MERCHANTABILITY AND FITNESS). SFCS LIABILITY FOR ANY AND ALL LOSSES AND DAMAGES RESULTING FROM ANY
CAUSE WHATSOEVER, INCLUDING WARRANTORS NEGLIGENCE, ALLEGED DAMAGED OR DEFECTIVE GOODS,
WHETHER SUCH DEFECTS ARE DISCOVERABLE OR LATENT, SHALL IN NO EVENT EXCEED THE PURCHASE PRICE OF
THE EQUIPMENT.
ATTENTION
For your protection in the event of theft or loss of this product,
please fill in the information below for your own personal records.
Model No.
Serial No.
(Located on back or bottom side of unit.)
Date of Purchase
Where PurchasedPurchase Price
LABORPA R T S
LAMP
1 YEAR
1 YEAR 90 DAYS