Sanyo Plc Ef30n Projector User Manual

							41
SETTING
Lamp counter reset
Move pointer to Lamp counter reset and then
press SELECT button.  
Move arrow to
replaced lamp number (Lamp 1 or Lamp
2) and then press 
SELECT button.
USB
Projector mode
Select   when controlling a projector with computer.
NOTE:Before you control a projector by computer, install USB driver
(optionally sold parts) and set up computer following instruc-
tion in USB driver package. Contact your authorized dealer.
This Projector is equipped with USB port for interactive operation
between a projector and computer. Set mode following steps below.
Wireless Mouse mode
Select   when controlling a computer with Remote Control of
this projector.
Be sure to reset Lamp Counter when Lamp Assembly is replaced.  When Lamp Replace Counter is reset, LAMP
REPLACE indicator stops lighting.
Turn projector on, press MENU button and ON-SCREEN
MENU will appear.  Press POINT LEFT/RIGHT button(s) to
move a red frame pointer to SETTING Menu icon.1
Press POINT DOWN button to move a red frame pointer to
“Lamp counter reset” and then press 
SELECT button.2
Do not reset Lamp Replace Counter except after Projection lamp is
replaced.
Another confirmation dialog box appears and select [Yes] to
reset Lamp Replace Counter.4
Move arrow to replaced lamp number (Lamp 1 or Lamp 2) and
then press 
SELECT button.  Message Lamp replace counter
Reset? is displayed. Move pointer to [Yes] and then press
SELECT button.3
NOTE:Be sure to reset correct lamp number otherwise LAMP
REPLACE indicator continues lighting.
Move a pointer to item and then
press POINT LEFT/RIGHT
button(s).
Press SELECT button at this icon to
display previous items.
USB
Message Lamp replace counter Reset? is
displayed. Move pointer to [Yes] and then
press SELECT button.
Closes SETTING MENU.
Quit
12 
						

							42
APPENDIX
OPERATING WIRELESS MOUSE
INSTALLATION
Wireless Remote Control Unit is not only able to operate this projector but also usable as a wireless mouse for most
Personal Computers.  POINT buttons and two CLICK buttons are used for wireless mouse operation.
This Wireless Mouse function is available only when PC mouse pointer is displayed on a projected screen.  When ON-
SCREEN MENU or any message / dialog box is displayed on screen instead of PC mouse pointer, this Wireless Mouse
function cannot be used.
Connect mouse port (or USB port) of your computer to Control
Port (or USB connector) of this projector with Control Cable (or
USB cable). (Refer to page 13, 14 for connection.)
Turn a projector on first, and then turn on your computer.  When
computer is switched on first, Wireless Mouse may not work
properly.
1
2
To use Wireless Remote Control Unit as Wireless Mouse for a Personal Computer, installation of mouse driver (not supplied)
is required.  Make sure that mouse driver is properly installed in your computer.  And make sure that mouse port (or USB
port) of a Personal Computer is activated.
OPERATING WIRELESS MOUSE
When controlling a PC mouse pointer, operate Wireless Mouse with POINT button, SELECT button, and RIGHT CLICK
button on Wireless Remote Control Unit.
Used to move PC mouse pointer.  Pointer is moved corresponding
with direction you are pressing.
POINT button
This button has same function as left button in a PC mouse.
SELECT (LEFT CLICK) button
This button has same function as right button in a PC mouse. This
button is not available for controlling this projector.
RIGHT CLICK button
Note : When your computer has no mouse
port, connect Serial Port of your
computer to Control Port of a projector
with Control Cable for Serial Port (not
supplied).
POINT button (Move pointer)
SELECT button
(left button of mouse)
RIGHT CLICK  button
(right button of mouse)
MAINTENANCE
WARNING TEMP. INDICATOR
WARNING TEMP. Indicator flashes red when an internal temperature of a projector exceeds normal temperature.  This
Indicator stops flashing when temperature of a projector returns to normal.
When WARNING TEMP. Indicator continues to flash, check items listed below.
Ventilation Slots of a projector may be blocked.  In such an event, reposition a projector so that Ventilation Slots are
not obstructed.
Air Filter may be clogged with dust particles.  Clean Air Filter by following section AIR FILTER CARE AND CLEANING
on next page.
1
2
If WARNING TEMP. Indicator remains on after performing above checks, Cooling Fans or Internal Circuits may be
malfunctioning.  Contact service personnel from an authorized dealer or a service station.3 
						

							43
APPENDIX
AIR FILTER CARE AND CLEANING
Turn power off, and disconnect AC power cord from
an AC outlet.1
2
Air Filter prevents dust from accumulating on a surface of Projection Lens and Projection  Mirror.  Should Air
Filter become clogged with dust particles, it will reduce Cooling Fans effectiveness and may result in internal
heat build up and adversely affect life of  projector.
Clean Air Filter following steps below: 
3
4
CAUTION
Do not operate a projector with Air Filter
removed.  Dust may accumulate on LCD
Panel and Mirror degrading picture quality.
Do not put small parts into Air Intake Vents.
It may result in malfunction of a projector.
RECOMMENDATION
We recommend avoiding dusty/smoky environments when operating a projector.  Usage in these
environments may cause poor image quality.
When using under dusty or smoky conditions, dust may accumulate on liquid crystal panel, lens, or optical elements inside it.
This condition may degrade quality of projected image.
When above symptoms are noticed, contact your authorized dealer or service station for proper cleaning.
Pull out 3 Air Filters and Air filter Covers from a
projector.
Clean each parts (Air Filter and Air filter Cover) with
brush or wash out dust and particles. Be sure to dry
them out.
Replace Air Filter and Air Filter Cover properly. Make
sure that they are fully inserted.
BOTTOM OF PROJECTORFRONT OF PROJECTORSIDE OF PROJECTOR
AIR FILTERAIR FILTER
COVERAIR FILTER AIR FILTER
COVER
AIR FILTER AIR FILTER
COVER
CLEANING PROJECTION LENS
Apply a non-abrasive camera lens cleaner to a soft, dry cleaning cloth.  Avoid using an excessive amount of cleaner.
Abrasive cleaners, solvents or other harsh chemicals might scratch lens.
When a projector is not in use, replace lens cover.
1
3
Lightly wipe cleaning cloth over lens.2
Follow these steps to clean projection lens: 
						

							44
APPENDIX
LAMP MANAGEMENT
This Projector is equipped with 2 Projection Lamps to ensure brighter image and those lamps are controlled by Lamp
Management Function.  Lamp Management Function detects status of two lamps and shows status on screen or on LAMP
REPLACE indicator.  This function also automatically controls Lamp Mode when any of lamps is out for end of life or
malfunctions. 
Lamp Status Display
Lamp Status Display appears on screen when power switch is on or changed input position (input 1, input 2 or input 3).
This shows status of each lamp as; ON, OFF, NEAR END, or OUT.  Refer to following for each status.
Projection Lamp lights normally.
Lamp Replace Indicator
This LAMP REPLACE indicator lights yellow when any of Projection Lamps is nearing its end, and flashes when any of them
becomes out.  Check number of lamp on Lamp Status Display and replace lamp.
Yellow Lamp
Dim Lamp
X Mark on Lamp
Red Lamp
LAMP REPLACE
INDICATOR
Projection Lamp is turned off.
Projection Lamp is nearing its end.  When image becomes
darker or color becomes unnatural, replace lamp.
(LAMP REPLACE indicator lights yellow.)
(LAMP REPLACE indicator flashes yellow.)
Projection lamp is defective or fails to be turned on. Restart a
projector on, and make sure lamp is on. If this mark still
appears, replace lamp corresponding with number marked X.
LAMP STATUS
DISPLAY
12
Lamp Mode Changeover
Lamp Management Function automatically changes combination of lighting lamp (Lamp Mode) by detecting status of lamp.
When any of 2 lamps becomes out, Lamp Mode is changed over from 2 lamps to 1 lamp. Lamp Mode can be switched to 2
lamps or 1 lamp manually.  Refer to SETTING section on page 39, 40
.
1212
2 LAMP MODE1 LAMP MODE
(Example)
12
30
12
LAMP STATUS
INPUT 1 
						

							45
APPENDIX
Check number of lamp to be replaced on Lamp Status
Display.
Loosen 3 screws on Lamp Cover and remove Lamp Cover.
(See right figure.)
1
3
Loosen 2 screws and pull out Lamp Assembly to be replaced
by grasping handle.4
Turn off a projector and disconnect AC Power Cord.  Allow a
projector to cool for at least 45 minutes.2
Replace Lamp Assembly with a new one and tighten 2 screws.
Make sure that Lamp Assembly is set properly
6
Follow these steps to replace lamp assembly.
Replace Lamp Cover and tighten 3 screws. 
5
7
8
Connect AC Power Cord to a projector and turn projector on.
Reset Lamp Replacement Counter. (Refer to section Lamp
Counter Reset on page 41.)
NOTE :Do not reset LAMP REPLACEMENT COUNTER
when lamp is not replaced.
CAUTION :DO NOT OPERATE A PROJECTOR WHILE ANY OF LAMPS IS REMOVED. IT MAY
RESULT IN MALFUNCTIONS, FIRE HAZARD, OR OTHER ACCIDENTS.
SCREWS
LAMP
COVER
SCREWS
ORDER REPLACEMENT LAMP
Replacement Lamp can be ordered through your dealer.  When ordering Projection Lamp, give following
information to dealer.
Model No. of your projector  : PLC-EF30N
Replacement Lamp Type No. : POA-LMP39(Service Parts No. 610 292 4848)
Make sure which number of lamp needs to be
replaced on Lamp Status Display.
Figure shows case of replacing LAMP 2.LAMP 1
LAMP 2
NOTES ON LAMP REPLACEMENT
To maintain quality of picture (better balance of color and brightness in entire screen), we recommend replacing
all 2 lamps at a time. 
LAMP REPLACEMENT
CAUTION
Do not drop a lamp assembly or touch a glass
bulb! Glass can shatter and may cause injury.
CAUTION
For continued safety, replace with a lamp
assembly of same type.
Allow a projector to cool for at least 45
minutes before you open Lamp Cover.  Inside
of a projector can become very hot. 
						

							Check audio cable connection from audio input source.
Adjust audio source.
Press VOLUME (+) button.
Press MUTE button.
46
APPENDIX
TROUBLESHOOTING
Before calling your dealer or service center for assistance, check matters below once again.
1. Make sure you have connected a projector to your computer or video equipment as described in section CONNECTING
PROJECTOR  on pages 12 ~ 15.
2. Check cable connection.  Verify that all computer, video and power cord are properly connected.
3. Verify that all power is switched on.
4. If a projector still does not produce an image, re-start your computer.
5. If an image still does not appear, unplug a projector from your computer and check your computer monitors
display.Problem may be with your graphics controller rather than with a projector.  (When you reconnect a projector, be
sure to turn a computer and monitor off before you power up a projector.  Power equipment back on in order of : Projector
and computer.)
6. If problem still exists, check following chart.
No power.Plug a projector into your AC outlet.
Turn MAIN ON/OFF switch to ON.
Press POWER ON/OFF switch to ON.
Make sure READY Indicator lights.
Wait 90 seconds after a projector is turned OFF when turning a projector back on.
NOTE :After pressing Power ON-OFF button to OFF, make sure a projector works as
follows:
1.  LAMP indicator lights bright and READY indicator turns off.
2. After 90 seconds, READY indicator lights green again and a projector may be
turned on by pressing Power ON-OFF button.
Check WARNING TEMP. indicator.  If indicator flashes red, a projector cannot be turned
on.
(See TURNING ON/OFF PROJECTOR section on page 21.)
Check Projection Lamp.  (Refer to page 45.)
Image is out of
focus.Adjust focus of a projector.
Check Projection Lens to see if it needs cleaning.
NOTE : Moving a projector from a cool temperature location to a warm temperature location
may result in moisture condensation on Projection Lens.  In such an event, leave a
projector OFF and wait until condensation disappears.
Picture is Left/Right
reversed.Check Ceiling / Rear feature.  (See “SETTING” section on page 39.)
Problem:Try these Solutions
Picture is
Top/Bottom
reversed.Check Ceiling feature.  (See “SETTING” section on page 39.)
Some displays are
not seen during
Operation.Check Display feature.(See “SETTING” section on page 39.)
No image.Check connection between your computer or video equipment and a projector.
When turning a projector on, it takes about 30 seconds to display an image.
Check system that you select is corresponding with your computer or video equipment.
Make sure temperature is not out of Operating Temperature (5°C ~ 35°C).
No sound. 
						

							Check cable connection between a projector and your computer.
Check mouse setting on your computer.
Turn a projector on before turning on a computer.
47
APPENDIX
SERVICE
WARNING: High voltages are used to operate this projector. Do not attempt to open cabinet.
You can often correct operating problems yourself. If a projector fails to work properly, see TROUBLESHOOT-
ING section on page 46, 47. To correct failure, try Solutions.
If after following all operating instructions, you find that service is necessary, contact Sanyo Service Station or
store where you purchased unit.
Give model number and explain difficulty. We will advise you how to obtain service.
This symbol on the nameplate means the product is Listed by Underwriters
Laboratories Inc.  It is designed and manufactured to meet rigid U.L. safety
standards against risk of fire, casualty and electrical hazards.
The CE Mark is a Directive conformity mark of the European Community (EC).
Remote Control Unit
does not work.Check batteries.
Check ALL-OFF switch on Remote Control Unit is set to “ON.”.
Make sure nothing is between Infrared Remote Receiver and Remote Control Unit.
Make sure you are not too far from a projector when using Remote Control Unit.
Maximum operating range is 16.4’ (5m).
Check transmitted signal mode from Remote Control Unit.
(See “SETTING” section on page 40.)
Problem:Try these Solution
Wireless Mouse
function does not
work. 
						

							Accessories
48
APPENDIX
Specifications are subject to change without notice.
TECHNICAL SPECIFICATIONS
1.8 TFT Active Matrix type, 3 panels
Multi-media Projector
48.6 lbs (22 kg)
17.3 x 9.1 x 23.8 (439 mm x 230 mm x 605.6 mm) 
1280 x 1024 dots
3,932,160 (1,280 x 1,024 x 3 panels)
PAL, SECAM, NTSC, NTSC4.43, PAL-M and PAL-N
Up and Down
800 TV lines
INT. SP. Stereo (R and L), 3 watt RMS (T.H.D. 10%)
41 ˚F ~ 95 ˚F (5 ˚C ~ 35 ˚C)
14 ˚F ~ 140 ˚F (-10 ˚C ~ 60 ˚C)
Owner’s Manual
AC Power Cord
Wireless/Wired Remote Control Transmitter and Batteries
Remote Control Cable
VGA Cable and DVI Cable
MAC/VGA Adapter and DVI/VGA Adapter
3 Types Control Cable (For PS/2, Serial and ADB port) 
3 Types Light-Block Sheet (For option lens)
Lens Mounting Adapter
Protective Dust Cover
Projector Type
Net Weight
Dimensions (W x H x D)
Panel Resolution
Number of Pixels
Color System
Scanning Frequency
Horizontal Resolution
Built-in Speakers
Operating Temperature
Storage Temperature
LCD Panel System
200 watt type x 2Projection Lamp
0˚ to 6.9˚Feet Adjustment
Power Source : AA, UM3 or R06 Type x 2
Operating Range : 16.4’ (5m) / ±30˚
Dimensions : 2.2” x 1.3” x 7.6” (55mm x 34mm x 192mm)
Net Weight : 0.36 lbs (165 g) (including batteries)
Laser Pointer : Class IILaser  
(Max. Output : 1mW / Wave length : 650±20nm)
Remote Control Transmitter
480i, 480p, 575i, 575p, 720p, 1035i, 1080i-50 and 1080i-60High Definition TV Signal
AC 100 ~ 120 V (7.8 A  Max. Ampere), 50 / 60 Hz  (The U.S.A and Canada)
AC 200 ~ 240 V (3.3 A  Max. Ampere), 50 / 60 Hz  (Continental Europe and The U.K.)
Voltage and 
Power Consumption
H-sync. 15 ~ 120 KHz, V-sync. 50 ~ 120 Hz
Motorized Lens Shift
DVI-I Terminal (Digital/Analog), RCA Type (Audio R and L)
and DIN 8-pin (Control port)Input 1 Jacks
BNC Type x 5 (R/Pr, G/Y, B/Pb, H/HV and V), RCA Type (Audio R and L)
and DIN 8-pin (Control port)Input 2 Jacks
BNC Type x 2 (VIDEO/Y, C), RCA Type (Audio R and L)
and DIN 4-pin (S-Video)Input 3 Jacks
Serial port in (DB 9), Serial port out (DB 9), USB port,
Audio Monitor out (RCA Type R and L) and Wired Remote Jack Other Jacks 
						

							49
APPENDIX
CONFIGURATIONS OF TERMINALS
Terminal : Mini DIN 8-PIN
Connect control port (PS/2, Serial or ADB port) on your computer to this terminal with Control Cable (supplied).
12
345876
Pin Configuration
CONTROL PORT CONNECTOR
-----
CLK
DATA
GND
-----
-----
GND
-----
R X D
-----
-----
GND
RTS
T X D
GND
GND
-----
ADB
-----
GND
-----
-----
-----
GND
PS/2SerialADB
1
2
3
4
5
6
7
8
DVI-I TERMINAL (DIGITAL/ANALOG) 
This terminal accepts only Digital (TMDS) or Analog (RGB) output signal. Connect display output terminal of computer to this
terminal with DVI cable (supplied).  
1917
21018
31119
41220
51321
61422
71523
81624
C1
C2
C3
C5C4
T.M.D.S. Data2–
No Connect
T.M.D.S. Data2+
No Connect
T.M.D.S. Data2 Shield
DDC Clock
DDC Data
Analog Vert. sync
1
5
2
4
3
6
7
8
Pin Configuration
T.M.D.S. Data1–
No Connect
T.M.D.S. Data1+
No Connect
T.M.D.S. Data1 Shield
+5V Power
Ground (for +5V)
Hot Plug Detect
9
13
10
12
11
14
15
16
T.M.D.S. Data0–
No Connect
T.M.D.S. Data0+
No Connect
T.M.D.S. Data0 Shield
T.M.D.S. Clock Shield
T.M.D.S. Clock+
T.M.D.S. Clock–
17
21
18
20
19
22
23
24
Analog Red Input
Analog Ground (R/G/B)
Analog Green Input
Analog Horiz. sync
Analog Blue Input
C1
C5
C2
C4
C3
-----
RxD
TxD
-----
Ground
-----
-----
-----
1
2
3
4
5
6
7
8
9-----
1 2 3 4 5
6 7 8 9
Connect serial port output terminal of computer to this terminal with Serial Cable (not supplied).
Pin Configuration
SERIAL PORT IN/OUT TERMINAL 
						

							50
APPENDIX
Vcc
- Data
+ Data
Ground
1
2
3
4
USB PORT TERMINAL
Pin Configuration
Connect USB port output terminal of computer or peripheral equipment to this terminal with USB port  Cable (not
supplied).
2
341