Sanyo Pdg Dwt50l Projector User Manual

							 
32 
3. Projecting an Image (Basic Operation) 
n Turning on the Projector 
Once the projector is correctly located and the power cable and ot her connections are in place, it is important that the pro-
jector is powered on correctly in order to avoid damage to components and unnecessary wear and tear. Refer to the 
following guide to power on the projector. 
1.   Connect the power cable (A). Press the 
main power switch to the on  (  I ) posi-
tion as shown (B). The power LED 
lights orange and warning LED lights 
green. 
B
A 
2.   Press the  On/Standby  button once (see 
OSD Controls and Status LEDS on 
page 7 ). The power LED lights green 
and the internal cooling fan starts. 
3.   After approximately 10 seconds, the 
power LED flashes intermittently green.
 
4.  The Lamp1 and Lamp2 LEDs light 
green and the Power LED flashes more 
rapidly.  
5.  Once the power LED is lit a solid green, 
the projector is ready for use.  
 
Note: 
If any of the LEDs remain flashing or blink there may be a problem with the startup. Please refer to the  
n Troubleshooting  section on page 102.  
						

							3. Projecting an Image (Basic Operation) 
33 
 
Note on Startup Screen (Menu Language Select screen) 
In the first instance of powering on the projector, the language menu is displayed to select the default language. 
 
Select the required default language using the  ▲ or  ▼ buttons on the OSD menu panel or the remote control unit and 
press  Select . 
Note: 
The language select screen only appears on the first instance of power o\
n. All subsequent operations as-
sume the selected default language. To change the default see page  74.  
						

							3. Projecting an Image (Basic Operation) 
34
 
o Selecting an Input Source 
The Input Source can be selected from the  projectors control panel or from the remote control unit. Refer to the following 
guide to select the Input Source. 
1.  Press  Menu on the OSD control panel or on the remote 
control unit to display the  Main Menu. Scroll to the 
Input menu using  ▲or▼ and press  Select. 
 
Note:  
Return to the projected image by pressing  Cancel 
twice. 
 
2.  Select the required source using  ▲or▼ and press  
Select . 
 
 
Note: 
If an XGA signal is not correctly recognized, set “WXGA Mode” to off (see page  63). 
To check if the signal is recognized, go to “Input” under “Information” menu (see page  90).  
						

							3. Projecting an Image (Basic Operation) 
35 
 
p Adjusting the Picture Position and Picture Size 
The Picture Position and Picture Size can be adjusted manually fr om the lens control panel or from the remote control unit. 
Refer to the following guides to adjust Picture Position manually. 
Adjusting Picture Position Manually 
1.  Press the Select keypad in any direction to 
bring up the Lens Shift window. 
 
2.  Press the directional key as required to 
shift the image. Releasing the  
directional arrow will  
re-center the cursor. 
3.  To alter the picture size, press  Menu and 
select the  Adjust menu using  ▲or▼. Press 
Select  to open the Adjust  menu. Press 
◄or ► to select  Image Options followed 
by  ▲or ▼ to select  Screen. Press  
Select . 
  
						

							3. Projecting an Image (Basic Operation) 
36
4.  The Screen  window is displayed. Select 
the desired picture size using  ▲or▼  and 
press  Select . 
 
5.  When finished, press Cancel  to return to 
the projected image.  
 
Lens Shift Adjustable Range 
The adjustable range for lens shift is tabulat ed below and subject to the conditions listed. 
Note: 
The drawings below apply to the standard lens (LNS-S40) only.  
  
						

							3. Projecting an Image (Basic Operation) 
37 
 
From the Remote Control Unit 
1.  Press the Lens Shift  button to bring up the 
Lens Shift window. 
 
2.  Press the directional keys as required to 
shift the image. Releasing the directional 
arrow will re-center the cursor. 
 
3.  To alter the picture size, press the Screen  
button to display the Screen  window. 
 
4.  Select the desired picture size using  ▲or▼  
and press Select .  
5.  When finished, press Cancel  to return to 
the projected image.  
  
						

							3. Projecting an Image (Basic Operation) 
38
Adjusting the Projector Level 
1.  To raise the level of the projector, twist the adjust-
ers clockwise. 
 
2.  To lower the level of the projector, lift the projector 
and twist the adjusters counter clockwise.  
 
  
						

							3. Projecting an Image (Basic Operation) 
39 
 
q Optimizing an RGB Image Automatically 
Adjusting the Image Using AUTO PC ADJ.
 
To optimize an RGB image automatically refer to the following guide. 
Press the AUTO PC button on the remote control (see item 17,  s Part Names of the Remote Control on page  11) or the 
AUTO PC ADJ. button on the OSD control  panel to optimize an RGB image automatically. 
This adjustment may be necessary when you c onnect your computer for the first time. 
  
						

							3. Projecting an Image (Basic Operation) 
40
 
r Adjusting Volume Up and Down 
The volume can be adjusted from the OSD Control Panel or with  the Remote Control unit. Refer to the following as a guide. 
1.  Press the Volume +/-  buttons on the remote 
control or the ◄  ► buttons on the OSD con-
trol panel. The volume level is displayed on 
screen. 
2.  Use the  Volume +/-  buttons or the  ◄ ► but-
tons on the OSD control panel to adjust the 
level. 
 
 
  
						

							3. Projecting an Image (Basic Operation) 
41 
 
s Turning off the Projector 
Once the projector is no longer required,  it is important to shut it down correctly to avoid damage or unnecessary wear and 
tear to the projector. 
CAUTION 
 • 
Do not unplug the power cable from the wall outlet  or projector when the projector is powered on. 
Doing so can cause damage to the AC IN connector of the projector and (or) the prong plug of the 
power cable. To turn off the AC power supply when the projector is powered on, use a power strip 
equipped with a switch and a breaker. 
•  Do not turn off the AC power supply within 10 seconds of making adjustment or setting changes 
and closing the menu. Doing so can cause loss  of adjustments and settings and return to default. 
 
Refer to the following guide to shut down the projector. 
1.  Press the On/Standby  button once. The Power Off 
window displays. 
 
2.  Press the  On/Standby  button or Select again on the 
OSD control panel or remote control to verify 
power off. 
The cooling fans continue  to operate (cooling-off 
time). 
The cooling fans stop operating when the projector 
turns off. 
3.  The projector enters Standby mode and the power 
LED lights orange. 
4.  Press the Main Power switch to the off position (O) 
to turn off the projector.