Sangean Ats606ap Shortwave Radio Owners Manual

							3.When the alarm time is set, the clock will return 
    to the current time automatically. Meanwhile the 
    colon will start to flash.
4.To verify, press  STANDBY  button then 
    ENTER  button again.50ATSLWMWSWATSATSMETER-STANDBY-TIMER
-STANDBY-
-STANDBY- 
						

							5.To cancel the alarm time, press  STANDBY  but-
    ton and display  STANDBY  will flash, press  
    C  button to cancel.
1.When alarm is on press  POWER/SLEEP  button to turn off the alarm.
2.The radio alarm will last for one hour if not turned off by pushing  POWER/SLEEP  button.
3.Tune the radio before setting radio alarm. When alarm is on, the radio will play according to last 
    frequency or station selected.NoteHWS-Humane Waking system.
A repeating beep tone sounds when using the set buzzer. The alarm buzzer volume increases every 
15 seconds for 1 minute then silences for 1 minute before beginning the cycle. Again HWS will continue 
this pattern for 30 minutes.SETTING ALARM BY HWS BUZZER5113mC 
						

							POWER/
   SLEEPAuto tuning systemSetting Alarm by HWS buzzer has same procedures 
as setting alarm by radio except pushing 
STANDBY-       HWS  button instead.
Turn off the HWS buzzer by pushing  POWER/
SLEEP  button.
.1.Press  TIMER  key,  TIMER  display will flashCOUNTING DOWN TIMER52ATSLWMWSWATSATSMETER
-STANDBY-TIMER 
						

							2.Use 0-9 button to key in required time (Max 23
    hours and 59 minutes).
3.Press  ENTER  button,  TIMER  display will
   stop flashing indicating Count Down timer has 
   been set. Display will be back to real time within 
   7 seconds after time is set.53120m90m75m
60m49m41m
31m25m21m
19m16m13m
1 2 3 
4 5 6 
7 8 
0C
9
M
ENTER
TIME  SET
DISPLAY 
						

							4.Push  TIMER  button again to see remaining
   time.
   a.Push  TIMER  button again to continue timer 
      function.
   b.Push  ENTER  button to re-start timer 
      function.
5.When timer is on, buzzer will last for one 
    minute, to turn off the buzzer, push  POWER/
    SLEEP  button.54METERSWTIMER
POWER/
   SLEEPAuto tuning system 
						

							6.To cancel timer setting:
   a: Press  TIMER  button. Display shows remain-
       ing time.
   b: Press  C  button  TIMER  on the display will 
       disappear, and display will show real time 
       immediately.
1.When alarm is on, press  POWER/SLEEP  
   button to turn off the alarm.
2.The alarm will last for one minute if not turned 
   off by pushing  POWER/SLEEP  button.
3. For initial operation on timer, display will show
              Meanwhile press  ENTER  button, display 
    shows  E  to indicate error operation.55METERSWTIMER
CNote 
						

							1.Push 
POWER/SLEEP  button for more than 2 
    seconds,  LCD            will  show indicating the 
     radio is in sleep (auto shut  off) function. A buzzer 
     will be heard this time, if the  radio is on.
2.Continue pushing   PLWER/SLEEP   but-
     ton. Sleep time can be adjusted by  60-45-30-
    15-60.
SETTING THE
 SLEEP TIMER
Y ou can  set the  sleep timer  with the radio on  or off.56POW
ER/
   SL EEPAuto tu ning  sy stem
PO W ER /
    S LE EPA uto  tu nin g s yste m
PO W ER /
    S LE EPA uto  tu nin g s yste m 
						

							3.Release  POWER/SLEEP  button whenever the 
   sleep time shown on the display is acceptable 
   to you.
4.To cancel sleep function, simply push  POWER/
    SLEEP  key. Display           will disappear and 
    return to the real time.57FMM
FMM
POWER/
   SLEEP
1 2 3 4 5 6 
						

							In addition to the standard tuning methods described previously, use following controls for special operations.MISCELLANEOUS CONTROLS1.When listening to FM stereo broadcasting and 
    using earphones, set the switch to STEREO 
    position to enjoy stereo programs.
2.When listening to AM (MW/LW/SW) broad-
    casting, this switch adjusts the receivers sensitivi-
    ty. When you listen to a strong station and the 
    signal is slightly distored, set the switch to the
    LOCAL position for best reception. For normal 
    or weak stations, set the switch to the DX 
    position for maximum sensitivity.MONO LOCAL/STEREO DX SWITCH58 
						

							While not a control, you may consider using Head-
phones to obtain the best audio clarity when listen-ing to SW. Since many SW stations broadcast onlymarginal signals, using Headphones will enable you to distinguish between the signal and the noise usually 
encountered at night. Be sure that, the Headphones terminate in a 1/8 inch plug, which is inserted into the 
Headphones jack located on the side of the radio, 
marked with the symbol        . When the Head - 
phones are plugged in, the speaker is muted.
Because the radio is capable of receiving FM stereo, 
the Headphones should be stereo so that your listening will be enhanced, When listening to stereo FM, be sure that the FM STEREO/MONO switch is set to the stereo position. This switch is located on the side of the radio.HEADPHONE USE59AM EXT
ANTFM
STEREOMONOAM
SENSDXLOVALDC I N 4.5V