Sangean Ats606ap Shortwave Radio Owners Manual

							Whenever the radio is turned off, the battery 
indicator will show for about 7 seconds to show 
battery condition. If the indicator falls below  2  
the batteries should be replaced.Be sure to replace
 the battery Within 3 minutes to secure time and all 
memory functions.BATTERY REPLACEMENT 
The receiver may be powered by using AC adap-tor. Insert the plug into the jack on the side of the radio marked DC IN 4.5V. Plug the other end of 
the adaptor into a standard household outlet. Whenever AC adaptor is used, the batteries are 
automatically disconnected.USING HOUSE CURRENT AC ADAPTOR101 2AM EXT
ANT
FM
STEREO
MONO
AM
SENS
DX
LOVAL
DC I N 4.5VAC AdapterDC IN 4.5V Jack 
						

							1.Turn off the power and battery indicator falls 
    below  2 .
2.IF E  flashes on LCD and low battery indicator 
   is displayed when radio is turned on batteries 
   should be replaced.TIME TO REPLACE BATTERIES111 2 
						

							3.Whenever the low battery indicator appears on 
   LCD display,batteries should be replaced.12 
						

							 
SETTING THE CLOCK
The time is displayed in the 24 hours mode since most shortwave broadcasting stations operate according 
to Greenwich Mean Time .This is the standard that is used through the world.PRELIMINARY SETTINGS1.The clock will start when 3  AA  batteries are 
installed. The display shows  0:00 
2.Press  TIME SET  key for more than 2 seconds, 
display will show          SET  and flash.13TIME SET 
						

							3.While      SET  is flashing ,set the correct time 
by pressing the numbered buttons .As you press 
the corresponding button the number shows up 
on the LCD display
4.If you press the wrong number, press the  C  
(cancel ) button which deletes one number at a
 time .
Note :Time can be adjusted only when        SET 
 is in flashing mode.14M.SCAN P1/P2120m90m75m60m49m41m31m25m21m19m16m13m1 2 3 
4 5 6 
7 8 
0C
9M.SCAN P1/P2120m90m75m60m49m41m31m25m21m19m16m13m
1 2 3 
4 5 6 
7 8 
0C
9 
						

							SETTING DUAL TIME 
A second time zone can be programmed into this unit such as your home time if you are travelling, or 
Greenwich Mean Time for instant access to shortwave broadcasting or local time wherever you are .5.Now press button  ENTER ,display will show 
   hours and minutes.1.Press                  button and display will 
   show and flash     .15ATSLWMWSWATSATSMETER
-STANDBY-TOMER 
						

							2.Press  ENTER  button within 3 seconds, display  
           will stop flashing.
 
3.Press  TIME SET  button for more than 2 
   seconds, display         SET will flash.16 
						

							4.While       SET  is flashing, set the correct time 
    by pressing the corresponding buttons. The 
    numbers will show up on the LCD display.
5.If you press the wrong number, press the  C  
    button which deletes one number at a time.17120m90m75m60m49m41m31m25m21m19m16m13m1 2 3 
4 5 6 
7 8 
0C
911mM
FREQ
ENTER
TIME  SETP1/P231m25m21m19m16m13m
7 8 
0C
911mM
FREQ
TIME  SET 
						

							6.Now press button  ENTER ,display shows 
   hours and minutes.
7.Push             button and  ENTER  again to 
   back to      time.18ATSLWMWSWATSATSMETER-STANDBY-TOMER 
						

							During time set period,
 display shows      SET ,
press  0set button, display will show   SET -00  
and flash. Now press   ENTER    button, the clock 
will start from its  zero second.
ZERO SECOND
 SET  190 SET   16m
SET.00