Samsung Syncmaster Vc240 User Manual

6.2 Picture
...
3
Select an option from
Color Tone.
...
4 If the option you want is not available, select Custom, and then adjust
R-Gain ,G-Gain , andB-Gain , which indicate red, blue, and green re-
spectively. To change the color tone of the picture to yellow, change
R-Gain andG-Gain to 100 and B-Gainto 0.
PresetColor Tone options are permanently defined. Custom settings
will be applied to Custom. Picture Size and Location
You can change the picture size and location in PC mode:
...
1 Press to open the...

6.2 Picture
...
4 Decrease or increase
Coarseto narrow or widen the picture respec-
tively. To finely adjust the picture width, select Fine.
...
5
If the picture is not centered on the screen, select PC Positionand then
adjust the picture location using the
, , , or button.
...
6
To reset the picture size and location, select Image Reset. Aspect Ratio
You can change the aspect ratio in PC or DVI mode:
...
1 Press to open the Setup screen, and go toPicture.
...
2 SelectPicture Options .
...
3...

6.2 Picture
for movies. VC Mode
Adjusting the Brightness and Color Intensity
You can change the brightness and color intensity:
...
1 Press to open the Setup screen, and go toPicture.
...
2 Select an option fromMode.
...
3
AdjustContrast ,Brightness ,Sharpness ,Color , andTint (G/R) for the
◀ 49 ▶        

6.2 Picture
selected option.
...
4 To reset the custom settings for the current Mode, select Picture Reset .
Then selectReset Picture Mode .
◀ 50 ▶  

6.2 Picture
Adjusting the Color Tone
You can change the color tone:
...
1 Press to open the Setup screen, and go to Picture.
...
2 Select Picture Options .
...
3
SetColor Tone toCool1 ,Cool2 ,Normal ,Warm1 , orWarm2 .
...
4 Noise can occur in the picture of a very dynamic video. To avoid noise, set
Digital NR toOff ,Low ,Medium ,High , orAuto .
◀ 51 ▶      

6.3 Security
6.3 Security
You can set the monitor to be accessed only via a password.
...
1 Press to open the Setup screen.
...
2 Select Security . Selecting Securitywill always display the following
password prompt. Enter the current password. The initial password is
0000. This is working only from 1004.17.
...
3
SetFunctions Lock toOn . ...
4 Because the initial password of most devices with a security function is
set to 0000, it is best to change the password. Enter a new password in
the Change PIN...

6.4 Reset Settings
6.4 Reset Settings
You can return the monitor to its default settings:
...
1 Press to open the Setup screen.
...
2 Select Reset Settings .
The monitor will restart itself after resetting. Note that all user con-
figurations and the call logs will also be deleted. 6.5 Software Update
You can update the monitor software over the network. This will allow you
to use additional functions. System supports two ways of software upgrade:
By pushing the software to the SCOPIA VC240 from iVIEW NMS...

6.5 Software Update
...
3
Select
SW Upgrade to start an update.
...
4 Enter the IP address of the software-update server in the input field, and
press
. Contact our service center or Radvision for getting the up-
dated released SW version. Upgrade server should be installed locally.
A software will appear on the server after setup. Refer to Chapter
5 for
details about Radvision.
...
5
Select the software for the product and start upgrade process. A software update cannot be performed during a call.
◀ 54 ▶...

7 Troubleshooting Guide
Check the following when there is a problem with the product.
...
1 If the status indicator is dark even when the monitor is powered on,
ensure the power cord is tightly connected to the monitor and socket.
...
2 If the message Check signal cable is displayed, tightly connect the
video cable to the monitor and PC.
...
3
If you remove and reconnect the video cable when Max. Power Saving
is set to On, the monitor may power off before it is recognized by the
PC. Be sure to change...

INDEX
Index
4:3 ,
48
12 Hours ,
24
16:9 ,
48
18/07/2010 ,
24
18:24 ,
24
24 Hours ,
24
123 ,
14
A
ABC ,
14
abc ,
14
Accept ,
28
Add Contact ,
32
Add Group ,
31
Address ,
19
All ,
32
Audio ,
29
AUDIO IN ,
10
Auto ,
25 , 51
Auto Adjustment ,
44 , 47
Auto Answer ,
28
B
B-Gain ,
44 , 47
Brightness ,
25 , 45 , 49
C
Call ,
35 , 38
Call Control ,
21 , 28 , 40
Call History ,
28 , 36
Call Quality ,
21 Call Type
, 27
Camera,
25
Change PIN,
52
Check signal cable,
55
Clock,
23
Clock Mode,
23
Clock Set,
23
Coarse,
48...