Samsung Syncmaster Vc240 User Manual

2.2 Assembling the Product
• Do not set the volume really high when you use headphones. A really
high volume may cause your hearing to weaken.
• Be sure the batteries are oriented in the right direction. Otherwise, a
fire, personal injury, or contamination may result from an explosion or
internal fluid leakage of the batteries.
• Used-up batteries (including rechargeable batteries) should be sepa-
rated from general waste so that they can be collected for recycling.
You can discard discharged batteries at...

2.2 Assembling the Product
...
4 Tightly fasten the screw on the bot-
tom of the base to the stand.
...
5
Be sure you do not remove the fix-
ing pin from the stand before you
connect the stand to the base. Oth-
erwise, injury may result. After
connecting the stand to the base,
remove the fixing pin, and adjust
the height of the stand. To fix the
height, fasten the fixing pin. Theft Prevention
A slot for connecting an anti-theft Kens-
ington lock can be found at the bottom
right on the back of the monitor....

2.2 Assembling the Product
Mounting the Monitor to a Wall
To mount the monitor to a wall, buy and attach to the monitor a 100 ☓100 or
200 ☓100 mm wall-mount bracket that complies with the VESA standards:
...
1 Unfasten the screw, and lift and re-
move the stand.
...
2 Attach the wall-mount bracket, and
fasten the screws.
Samsung is not liable for any defect caused by using a wall-mount bracket
that does not comply with the VESA standards. Blocking Electromagnetic Waves
The ferrite core can be used to...

2.3 Connections
2.3 Connections Connecting to a PC
The monitor has two video inputs for
connecting to a PC. One is for DVI,
and the other is for VGA. Using a dig-
ital signal, DVI offer clearer pictures
than VGA which uses an analog signal.
Thus, it is best to connect the monitor to
a PC via DVI rather than VGA.
Connect the DVI cable from the DVI IN
socket on the monitor to the DVI out-
put on the PC. Alternatively, connect
the VGA cable to the RGB INsocket on
the monitor and RGB OUT on the PC.
The...

2.4 Finding the Best Viewing Angle
Connections for Video Calls
To make a video call, the monitor
should be connected to a network.
Connect the LAN cable from the LAN
port on the router to the LANport on
the monitor. If the router has no more
ports available for the monitor, connect
one port on the monitor to the router
and then the other port on the monitor
to the PC. Then the PC can communi-
cate with the router via the monitor.
The monitor ’s camera has a micro-
phone at the bottom; however, a head-...

2.5 Powering On the Monitor
2.5 Powering On the Monitor
Before you power on the monitor, insert the bat-
teries into the remote control, observing the po-
larity, which is marked on the base of the battery
compartment.
If the monitor does not respond to the remote
control, the batteries have been discharged. Be
sure to replace the batteries using standard 1.5V
AAA, taking into account the precautions below:
• Do not use different types of batteries together.
• Do not use a new and used battery together....

2.6 Navigating between Menus
Table 3: Video signal mode
Resolution Horizontal Vertical Clock Horizontal/Vertical
frequency frequency frequency polarities
(kHz) (Hz)(MHz) (H/V)
IBM, 640 ☓350 31.469 70.086 25.175 +/-
IBM, 720 ☓400 31.469 70.087 28.322 -/+
MAC, 640 ☓480 35.000 66.667 30.240 -/-
MAC, 832 ☓624 49.726 74.551 57.284 -/-
MAC, 1152 ☓870 68.681 75.062 100.000 -/-
VESA, 640 ☓480 31.469 59.940 25.175 -/-
VESA, 640 ☓480 37.861 72.809 31.500 -/-
VESA, 640 ☓480 37.500 75.000 31.500 -/-
VESA, 800 ☓600...

2.7 Keyboard Modes
2.7 Keyboard Modes
You can type in uppercase letters, lowercase letters, numbers, and several
symbols using three types of keyboard modes. The current keyboard mode
is shown in the right side of the field: ABCindicates uppercase mode, abc
lowercase mode, and 123number mode.
To change the keyboard mode, press
repeatedly until the keyboard
mode you want is displayed. To type in
John@Office , follow the steps below:
...
1 To type an uppercase J, press
to switch to uppercase mode, and
press...

2.8 Power-saving Modes
2.8 Power-saving Modes
As shown in Table 4 , there are three types of power supply modes. The moni-
tor enters active mode after you have pressed
and the monitor has turned
on.
Table 4:
Power specification
Input power 100–240 V
Active mode Less than 85 W
Standby mode Less than 35 W
Max. power-saving mode Less than 3 W
Max. Power Saving Mode
With this mode active, the monitor can save energy by automatically switch-
ing itself to maximum power-saving mode when it is in DVI or PC mode...

2.8 Power-saving Modes
...
2 Press to open the Setup screen.
...
3
Select an interval for activating Standbymode. Each interval is a mul-
tiple of 10 minutes from 10 to 60 minutes.
IfStandby is set to 10 minutes, the monitor will automatically turn off
and switch to standby mode after the remote control has been left idle
for 10 minutes.
...
4 To turn on the monitor again, press any button other than .
The monitor will automatically turn on when a call is received during
standby mode. However, the...