Samsung Syncmaster 940mw Quick Start Guide

 Cable
D-Sub Cable  Audio Cable Power Cord
 Others
Remote Control  Batteries (AAA X 2) Connecter
 Sold separately
DVI CableRCA Cable (Video-Yellow, 
Audio-Red and White)Component(PR, PB, Y) Cable
S-Video Cable  Earphones/Headphones SCART Cable
TV antenna cable
 

Front
1. SOURCE  2. PIP 3. MENU 4.   CH   5. - VOL +
6. [   ] Enter button 
7. [   ] Power button 8. Power indicator 9. Remote Control Sensor  10. Speaker
1. SOURCE
Press the SOURCE button to change the input signal source.  
Changing the source is allowed only in external devices that are connected to the monitor 
at the time.  
To switch Screen modes:  
[PC] 
ç [DVI] 
ç [TV] 
ç [Ext.] 
ç [AV] 
ç [S-Video] 
ç [Component] 
>>Click here to see an animation clip
According to broadcasting type in each...

Rear 
(The configuration at the back of the monitor may vary from product to product.) 
1. POWER  
Power terminal 
Connect the power cord for your monitor to the POWER on 
the back of the monitor. 
This product may be used with 100 ~ 240VAC(+/- 10%).  
2. DVI/PC IN  
DVI/PC IN 
1.
DVI(HDCP)
: Connect the DVI cable to the DVI(HDCP) port on the 
back of your monitor.  
2.
RGB
: Connect the signal cable to the RGB port on the back 
of your monitor. 
3.
AUDIO
: PC sound terminal (input) 
3. EXT(RGB)...

4. COMPONENT IN COMPONENT IN
1.
R - AUDIO - L
: DVD/DTV sound input terminal (left/right)  
2.
P
R, PB,Y
: DVD/DTV video input terminal(PR, PB,Y)
5. ANT IN 
ANT IN
Connect the CATV cable or TV antenna cable to the ANT 
IN port on the rear side of the monitor. Make sure to use a 
TV antenna cable (sold separately) as the antenna cable.  
6.
 / S-VIDEO / VIDEO / L - AUDIO - R
1.   
: Headphone sound output terminal  
2.
S-VIDEO
: External device (S-video) input terminal 
3.
VIDEO
: External device (video)...

See Connecting the monitor for further information regarding cable connections. 
Remote Control 
The performance of the remote control may be affected by a TV or other electronic device operated near 
the monitor, causing malfunction due to interference with frequency.
1. POWER 
2. Number button 
3. +100, -/--
4. -  +
5.
 MUTE 
6. TTX/MIX
7.
 MENU
8.
ENTER
9.  CH/P   
10.
SOURCE 
11.
INFO
12.
EXIT 
13. Up-Down Left-Right buttons 
14. AUTO 
15. P.MODE, M/B (MagicBright™)
16. P.SIZE 
17. STILL 
18.PIP 
19....

2. Number button 
Selects TV channels in the TV mode.  
Used to change channels when PIP is selected and the PIP Source is set to TV.  
3. +100  
Press to select channels over 100.  
For example, to select channel 121, press +100, then press 2 and 1. 
-
/-- (One/Two-Digit channel selection )Use to select a channel numbered ten or over.  
Press this button, and the -- symbol is displayed.  
Enter the two-digit channel number.  
This function is available only in Europe. 
4. -  + 
Adjusts the audio volume....

17. STILL - Operates only for the CVBS, S-Video and RF Signal sources.
Press the button once to freeze the screen. Press it again to unfreeze.  
18.PIP - Available in PC/DVI Mode
Push the PIP button to turn PIP screen On/Off.  
19. S.MODE 
( Sound Mode )When you press this button, current mode is displayed on the lower center of the screen.  
The monitor has a built-in high fidelity stereo amplifier.  
Then push button again to circle through available preconfigured modes.  
( Standard 
ç Music 
ç...

     
 
 
Connecting the monitor 
1.Connecting to a Computer
1.Connect the power cord for your monitor to the POWER on the back of the monitor. 
Plug the power cord for the monitor into a nearby outlet.
2-1. Using the D-sub (Analog) connector on the video card.  
Connect the signal cable to the 
RGB port on the back of your monitor. 
 
2-2. Using the DVI (Digital) connector on the video card. 
Connect the DVI cable to the 
DVI(HDCP) port on the back of your monitor.  
 
3. Connect the 
(DVI/PC IN) AUDIO...

 
1. Using the D-sub (Analog) connector on the video card.  Connect the signal cable to the D-SUB port on the Macintosh computer. 
 
 
2. For older model Macintoshes, you need to adjust th e resolution control DIP switch on the Macintosh 
adapter (optional) referring to the switch  configuration table shown on its rear. 
 
3. Turn on the monitor and Macintosh.   
   
 
Connecting to Other devices 
This monitor allows the user to connect it to such input devices as a DVD player, a VCR or 
camcorder, or a...

3. Then, start the DVD, VCR or Camcorders with a DVD disc or tape inserted.  
4. Select AV or S-Video using the  SOURCE.  
 
   
1-2. Connecting EXT.(RGB) - It only applies to AV DEVICE that supports SCART. 
Connect to the DVD Devices input if the device has a EXT (RGB) jack.  
You can watch DVD simply by hooking up the DVD player with the monitor as long as the power 
is on. 
1. Connect the
 EXT (RGB) port of the monitor to the DVD Player using a SCART jack. 
 
2. Select Ext. by using the SOURCE.  
 
2....