Samsung Syncmaster 940mw Quick Start Guide

							 Cable
D-Sub Cable  Audio Cable Power Cord
 Others
Remote Control  Batteries (AAA X 2) Connecter
 Sold separately
DVI CableRCA Cable (Video-Yellow, 
Audio-Red and White)Component(PR, PB, Y) Cable
S-Video Cable  Earphones/Headphones SCART Cable
TV antenna cable
 
						

							Front
1. SOURCE  2. PIP 3. MENU 4.   CH   5. - VOL +
6. [   ] Enter button 
7. [   ] Power button 8. Power indicator 9. Remote Control Sensor  10. Speaker
1. SOURCE
Press the SOURCE button to change the input signal source.  
Changing the source is allowed only in external devices that are connected to the monitor 
at the time.  
To switch Screen modes:  
[PC] 
ç [DVI] 
ç [TV] 
ç [Ext.] 
ç [AV] 
ç [S-Video] 
ç [Component] 
>>Click here to see an animation clip
According to broadcasting type in each country, you may not be able to choose.  
For more information > Broadcasting Systems 
2. PIP - Available in PC/DVI Mode
In PC mode, turns on Video or TV screens in PIP mode.  
>>Click here to see an animation clip
3. MENU
Use this button for open the on-screen menu and exits from the menu screen or closes 
screen adjustment menu.  
4.  CH   
Moves from one menu item to another vertically or adjusts selected menu values.  
In TV mode, selects TV channels.  
>>Click here to see an animation clip
5. - VOL + 
Moves from one menu item to another horizontally or adjusts selected menu values.  
Adjusts the audio volume.  
>>Click here to see an animation clip
6. [   ] Enter button 
Activates a highlighted menu item.  
7. [   ] Power button 
Use this button to turn the monitor on and off.
8. Power indicator
Power indicator shows PowerSaver mode by green blinking. 
9. Remote Control Sensor  
Aim the remote control towards this spot on the monitor.  
10. Speaker  
You can hear sound by connecting the soundcard of your PC to the monitor.  
See PowerSaver described in the manual for further information regarding power saving functions.  
For energy conservation, turn your monitor OFF when it is not needed or when leaving it unattended 
for long periods. 
 
						

							Rear 
(The configuration at the back of the monitor may vary from product to product.) 
1. POWER  
Power terminal 
Connect the power cord for your monitor to the POWER on 
the back of the monitor. 
This product may be used with 100 ~ 240VAC(+/- 10%).  
2. DVI/PC IN  
DVI/PC IN 
1.
DVI(HDCP)
: Connect the DVI cable to the DVI(HDCP) port on the 
back of your monitor.  
2.
RGB
: Connect the signal cable to the RGB port on the back 
of your monitor. 
3.
AUDIO
: PC sound terminal (input) 
3. EXT(RGB) 
External device terminal  
EXT(RGB) is mainly used in Europe. 
As for EXT(RGB) port of the monitor, it makes TV or Video 
signal input and output. 
 
						

							4. COMPONENT IN COMPONENT IN
1.
R - AUDIO - L
: DVD/DTV sound input terminal (left/right)  
2.
P
R, PB,Y
: DVD/DTV video input terminal(PR, PB,Y)
5. ANT IN 
ANT IN
Connect the CATV cable or TV antenna cable to the ANT 
IN port on the rear side of the monitor. Make sure to use a 
TV antenna cable (sold separately) as the antenna cable.  
6.
 / S-VIDEO / VIDEO / L - AUDIO - R
1.   
: Headphone sound output terminal  
2.
S-VIDEO
: External device (S-video) input terminal 
3.
VIDEO
: External device (video) input terminal  
4.
L - AUDIO - R
: External device sound input terminal  
7.Kensington Lock
The Kensington lock is a device used to physically fix the 
system when using it in a public place.  
(The locking device has to be purchased separately.)  
For using a locking device, contact where you purchase 
it.
 
						

							See Connecting the monitor for further information regarding cable connections. 
Remote Control 
The performance of the remote control may be affected by a TV or other electronic device operated near 
the monitor, causing malfunction due to interference with frequency.
1. POWER 
2. Number button 
3. +100, -/--
4. -  +
5.
 MUTE 
6. TTX/MIX
7.
 MENU
8.
ENTER
9.  CH/P   
10.
SOURCE 
11.
INFO
12.
EXIT 
13. Up-Down Left-Right buttons 
14. AUTO 
15. P.MODE, M/B (MagicBright™)
16. P.SIZE 
17. STILL 
18.PIP 
19. S.MODE 
20. DUAL/MTS
21. PRE-CH 
22.SOURCE 
23.SIZE 
24.POSITION 
25. MAGIC-CH
1.  POWER 
Use this button to turn the monitor on and off. 
 
						

							2. Number button 
Selects TV channels in the TV mode.  
Used to change channels when PIP is selected and the PIP Source is set to TV.  
3. +100  
Press to select channels over 100.  
For example, to select channel 121, press +100, then press 2 and 1. 
-
/-- (One/Two-Digit channel selection )Use to select a channel numbered ten or over.  
Press this button, and the -- symbol is displayed.  
Enter the two-digit channel number.  
This function is available only in Europe. 
4. -  + 
Adjusts the audio volume. 
5.  MUTE 
Press to mute the sound temporarily. 
Displayed on the bottom left of the screen.  
Press the MUTE button again to cancel the Mute function.  
Alternatively press the -   + buttons to cancel the Mute function.  
6. TTX/MIX  
TV channels provide written information services via teletext.  
For more information > TTX / MIX 
This function is available only in Europe. 
7.  MENU  
Use this button to open the on-screen menu and exit from the menu screen or close screen 
adjustment menu. 
8. ENTER  
Activates a highlighted menu item.  
9.  CH/P    
In TV mode, selects TV channels.  
10. SOURCE 
Press the SOURCE button to change the input signal source.  
Changing the source is allowed only in external devices that are connected to the monitor at 
the time.  
11. INFO  
Current picture information is displayed on the upper left corner of the screen. 
12. EXIT 
Exits from the menu screen.  
13.  U
p-Down Left-Right buttons Moves from one menu item to another horizontally, vertically or adjusts selected menu 
values.  
14. AUTO - Available In PC mode Onl
yAdjusts the screen display automatically.  
15. P.MODE, M/B 
(MagicBright™)Press to select a pre-defined Picture Mode of the monitor or to change the picture 
atmosphere as required. 
When you press this button, current mode is displayed on the lower center of the screen.  
TV / AV / Ext. / S-Video /Component Mode : P.MODE( Picture Mode )
The monitor has four automatic picture settings that are preset at the factory.  
Then push button again to circle through available preconfigured modes.  
( Dynamic 
ç Standard 
ç Movie 
ç Custom )  
PC / DVI Mode : M/B ( MagicBright™ )
MagicBright™ is a new feature providing the optimum viewing environment depending on 
the contents of the image you are watching.  
Then push button again to circle through available preconfigured modes.  
( Entertain
ç Internet 
ç Text 
ç Custom )  
16. P.SIZE - Not available in PC/DVI Mode
Press to change the screen size.  
( Auto Wide 
ç Wide 
ç Zoom 
ç 4:3 )  
Zoom are not available in 1080i(or over 720p) of DTV. 
 
						

							17. STILL - Operates only for the CVBS, S-Video and RF Signal sources.
Press the button once to freeze the screen. Press it again to unfreeze.  
18.PIP - Available in PC/DVI Mode
Push the PIP button to turn PIP screen On/Off.  
19. S.MODE 
( Sound Mode )When you press this button, current mode is displayed on the lower center of the screen.  
The monitor has a built-in high fidelity stereo amplifier.  
Then push button again to circle through available preconfigured modes.  
( Standard 
ç Music 
ç Movie 
ç Speech 
ç Custom )  
20. DUAL / MTS  
DUAL : STEREO/MONO, DUAL l / DUAL ll and MONO/NICAM MONO/NICAM STEREO 
can be operated depending on broadcasting type by using DUAL button on the remote 
control while watching TV. 
MTS : You can select the MTS (Multichannel Television Stereo) mode.  
. Mono, Stereo, SAP (Separate Audio Program)  
Set MTS to ON to choose Mono, Stereo or SAP.  
21. PRE-CH  
This button is used to return to the immediately previous channel.  
22.SOURCE - Ad
justable when the PIP function is ON.
Selects the Video source.  
23.SIZE - Ad
justable when the PIP function is ON.
You can switch the PIP picture size.  
24.POSITION - Ad
justable when the PIP function is ON.
Changes the Position of the PIP window.  
25. MAGIC-CH  
MagicChannel enables you to watch only certain channels. 
This function is available only in Korea.
 
						

							     
 
 
Connecting the monitor 
1.Connecting to a Computer
1.Connect the power cord for your monitor to the POWER on the back of the monitor. 
Plug the power cord for the monitor into a nearby outlet.
2-1. Using the D-sub (Analog) connector on the video card.  
Connect the signal cable to the 
RGB port on the back of your monitor. 
 
2-2. Using the DVI (Digital) connector on the video card. 
Connect the DVI cable to the 
DVI(HDCP) port on the back of your monitor.  
 
3. Connect the 
(DVI/PC IN) AUDIO  port on the rear side of the monitor to the sound card of the PC.
4. Turn on both your computer and the monitor.
 
 
2. Connecting to a Macintosh 
 
						

							 
1. Using the D-sub (Analog) connector on the video card.  Connect the signal cable to the D-SUB port on the Macintosh computer. 
 
 
2. For older model Macintoshes, you need to adjust th e resolution control DIP switch on the Macintosh 
adapter (optional) referring to the switch  configuration table shown on its rear. 
 
3. Turn on the monitor and Macintosh.   
   
 
Connecting to Other devices 
This monitor allows the user to connect it to such input devices as a DVD player, a VCR or 
camcorder, or a DTV or TV without disconnecting the PC.  
The configuration at the back of the monitor may vary from product to product.  
 
1-1. Connecting AV Devices 
The monitor has AV connection terminals to connect AV input devices like DVDs, VCRs or 
Camcorders. You may enjoy AV signals as long as the monitor is turned on. 
1. Input devices such as DVD, VCR or Camcorder are connected to the VIDEO or S-VIDEO terminal of the monitor using the Video or S-Video cable. 
 
2. Connect the port of the DVD, VCR (DVD / DTV Set-Top Box) to the  R-AUDIO-L port of the monitor. 
 
 
						

							3. Then, start the DVD, VCR or Camcorders with a DVD disc or tape inserted.  
4. Select AV or S-Video using the  SOURCE.  
 
   
1-2. Connecting EXT.(RGB) - It only applies to AV DEVICE that supports SCART. 
Connect to the DVD Devices input if the device has a EXT (RGB) jack.  
You can watch DVD simply by hooking up the DVD player with the monitor as long as the power 
is on. 
1. Connect the
 EXT (RGB) port of the monitor to the DVD Player using a SCART jack. 
 
2. Select Ext. by using the SOURCE.  
 
2. Connecting TV 
You may view television programs on the monitor if it is connected to an antenna or CATV cable 
without installing any separate TV reception hardware or software on your computer. 
1. Connect the CATV cable or TV antenna cable to the ANT IN port on the rear side of the monitor.  Make sure to use a TV antenna cable (sold separately) as the antenna cable. 
 
 
2. Turn on the monitor.   
3. Select TV using the  SOURCE. 
 
4. Select a desired TV channel.     When using an interior antenna terminal:
 
     Check the antenna terminal on the wall first and connect the antenna cable.
  When using an outdoor antenna:  
     If you are using an outdoor antenna, us e a professional for installation if possible.
  To connect the RF cable to the antenna input terminal:  
     Keep the copper wire portion of the RF cable straight.