Samsung Syncmaster 920lm Quick Start Guide

							1. Click 
Start , 
Setting , 
Control Panel.  
2. Double click the 
Display Icon.  
3. Choose the 
Settings tab and then click 
Advanced...  
4. Choose 
Monitor.  
5. Click 
Driver and then click on 
Update Driver.. then click on the Next button.  
6. Choose 
Display a list of the known drivers for this device so that I can choose a 
specific driver then click 
Next and then click 
Have disk.  
7. Click the 
Browse button then choose A:(D:\Driver).  
8. Click the 
Open button, then click 
OK button.  
9. Choose your monitor model and click the 
Next button then click 
Next button.  
10. Click the 
Finish button then the 
Close button.  
If you can see the 
Digital Signature Not Found window then click the 
Yesbutton. 
And click the 
Finish button then the 
Close button.  Case1: If the Properties button is inactive, it means your monitor is properly configured. 
Please stop installation 
Case2: If the Properties button is active, click the Properties button then follow next steps 
continually.
 
 
 
   Microsoft® Windows® Millennium Operating System 
 
1. Click 
Start , 
Setting , 
Control Panel.  
2. Double click 
Display icon.  
3. Select the 
Settings tab and click 
Advanced Properties button.  
4. Select the 
Monitor tab.  
5. Click the 
Change button in the 
Monitor Type area.  
6. Choose 
Specify the location of the driver.  
7. Choose 
Display a list of all the driver in a specific location.. then click 
Next button.  
8. Click the 
Have Disk button  
9. Specify A:\(D:\driver) then click 
OK button.  
10. Select 
Show all devices and choose the monitor that corresponds to the one you 
connected to your computer and click 
OK.  
11. Continue choosing 
Close button and 
OK button until you close the Display Properties 
dialogue box.  
 
 
 
   Microsoft® Windows® NT Operating System 
 
1. Click 
Start, 
Settings, 
Control Panel, and then double-click 
Display icon.  
2. In Display Registration Information window, click Settings Tab and then click 
All Display 
Modes.  
3. Select a mode that you wish to use (Resolution, Number of colors and Vertical frequency) 
and then click 
OK.  
4. Click 
Apply button if you see the screen working normally after clicking 
Test. If the screen is 
not normal, change to a different mode (lower mode of resolution, colors or frequency).  
If there is no Mode at 
All Display Modes, select the level of resolution and vertical 
frequency by referring to the Preset Timing Modes in the user guide.
 
 
 
   Linux Operating System 
 
        To execute X-Window, you need to make the X86Config file, which is a type of system setting file. 
 
 
1. Press Enter at the first and the second screen after executing the X86Config file.  
2. The third screen is for 
setting your mouse.  
3. Set a mouse for your computer.  
4. The next screen is for 
selecting a keyboard.  
5. Set a Keyboard for your computer.  
6. The next screen is for 
setting your monitor.  
7. First of all, set a 
horizontal frequency for your monitor. (You can enter the frequency 
directly.)  
8. Set a 
vertical frequency for your monitor. (You can enter the frequency directly.)  
9. Enter the 
model name of your monitor. This information will not affect the actual execution 
of X-Window.  
10. You have 
finished setting up your monitor.  
Execute X-Window after setting other requested hardware.  
 
						

							 
 
1. [ ]Use this button to open the on-screen menu and exit from the menu screen or close screen 
adjustment menu. 
2. [ ]These buttons allow you to adjust items in the menu.
3. [ ]Press this button to activate a highlighted menu item.
4. [
AUTO ]Press to self-adjust to the incoming PC signal. The values of fine,coarse and position are 
adjusted automatically.
 
 AUTO 
 
						

							Menu Description
AUTO When the 
AUTO button is pressed, the Auto Adjustment screen appears 
as shown in the animated screen on the center. 
Auto adjustment allows the monitor to self-adjust to the incoming video 
signal. The values of fine, coarse and position are adjusted automatically.  
(Available in analog mode only) 
 
To make the automatic adjustment function sharper, execute the AUTO 
function while the AUTO PATTERN is on. 
 
- If auto adjustment does not work properly, press AUTO button again to 
adjust picture with more accuracy. 
 
- If you change resolution in the control panel, auto function will be 
executed automatically. 
 
 
 OSD Lock & Unlock 
 
 When pressing the AUTO button after locking the OSD
 
						

							 
 
 When pressing the MENU button after locking the OSD
 
Menu Description
LockedThis is the function that locks the OSD in order to keep the current states of 
settings or prevent others from adjusting the current settings.  
 
Lock : Hold down the menu button for more than five seconds to activate 
the OSD adjustment lock function. 
 
Unlock : Hold down the menu button for more than five seconds to 
deactivate the OSD adjustment lock function. 
 
Though the OSD adjustment lock function is activated, you can still 
adjust the brightness and contrast, and adjust MagicBright ( ) 
using the Direct button.
 
 
 
						

							 MagicBright™ 
 
Menu Description
 
MagicBright™Then push the MagicBright button again to circle through available 
preconfigured modes. 
- Four different modes(Custom/Text/Internet/Entertain) 
 
 
 Brightness 
Menu Description
 
BrightnessWhen OSD is not on the screen, push the button to adjust brightness.
 
 
 
						

							 
 
 
  Picture Brightness Contrast
  Color Color Tone Color Control Gamma
  Image Coarse Fine Sharpness H-Position V-Position
  OSD Language H-Position V-Position Transparency Display Time
  Setup Image Reset Color Reset
  Information
 Picture  
Menu Description Play/Stop
BrightnessYou can use the on-screen menus to change the 
brightness according to personal preference.  
 
Direct Access Feature : When OSD is not on the screen, 
push the [   ] button to adjust brightness.  
 
[MENU →
  →
  →
 ,  →
 MENU]
ContrastYou can use the on-screen menus to change the contrast 
according to personal preference.  
 
[MENU →
  →
 ,  →
  →
 ,  →
 MENU]
 
 
 
 
 Color  
 
						

							Menu Description Play/Stop
Color ToneThe tone of the color can be changed and one of four 
modes can be selected - Cool, Normal, Warm and 
Custom.  
[MENU →
 ,  →
  →
 ,  →
  →
 ,  →
 MENU]
Cool- Makes whites bluish.
Normal- Keeps whites white.
Warm- Makes whites reddish.
Custom- Select this mode when you want to adjust 
the image according to your preferences.
Color ControlAdjusts individual R,G,B color balance. 
 [MENU →
 ,  →
  →
 ,  →
  →
 ,  →
  →
 ,  →
 MENU]
GammaGamma correction changes the luminance of the colors 
with intermediate luminance. zMode 1  zMode 2  
zMode 3  
[MENU →
 ,  →
  →
 ,  →
  →
 ,  →
 MENU]
 
 
 
 
 Image  
 
						

							Menu Description Play/Stop
CoarseRemoves noise such as vertical stripes. Coarse 
adjustment may move the screen image area. You may 
relocate it to the center using the horizontal control menu. 
(Available in analog mode only) 
 
[MENU →
 ,  →
  →
  →
 ,  →
 MENU]
Fine Removes noise such as horizontal stripes. If the noise 
persists even after fine tuning, repeat it after adjusting the 
frequency (clock speed). 
(Available in analog mode only) 
 
[MENU →
 ,  →
  →
 ,  →
  →
 ,  →
 MENU]
SharpnessChanges the clearance of image. 
 [MENU →
 ,  →
  →
 ,  →
  →
 ,  →
 MENU]
H-PositionChanges the horizontal position of the monitors entire 
display. 
(Available in analog mode only) 
 
[MENU →
 ,  →
  →
 ,  →
  →
 ,  →
 MENU]
V-PositionChanges the vertical position of the monitors entire 
display. 
(Available in analog mode only) 
 
[MENU →
 ,  →
  →
 ,  →
  →
 ,  →
 MENU]
 
 
 
 
 OSD  
 
						

							Menu Description Play/Stop
LanguageYou can choose one of 9 languages. 
 
Note:The language chosen affects only the language of 
the OSD. It has no effect on any software running on the 
computer. 
 
[MENU →
 ,  →
  →
  →
 ,  →
 MENU]
H-PositionYou can change the horizontal position where the OSD 
menu appears on your monitor. 
 
[MENU →
 ,  →
  →
 ,  →
  →
 ,  →
 MENU]
V-PositionYou can change the vertical position where the OSD menu 
appears on your monitor. 
 
[MENU →
 ,  →
  →
 ,  →
  →
 ,  →
 MENU]
TransparencyChange the transparency of the background of the OSD. 
 [MENU →
 ,  →
  →
 ,  →
  →
 ,  →
 MENU]
Display TimeThe menu will be automatically turned off if no adjustments 
are made for a certain time period.  
You can set the amount of time the menu will wait before it 
is turned off. 
 
[MENU →
 ,  →
  →
 ,  →
  →
 ,  →
 MENU]
 
 
 
 
 Setup  
 
						

							Menu Description Play/Stop
Image ResetImage parameters are replaced with the factory default 
values. 
 
[MENU →
 ,  →
  →
 ,  →
  →
 ,  →
 MENU]
Color ResetColor parameters are replaced with the factory default 
values. 
 
[MENU →
 ,  →
  →
 ,  →
  →
 ,  →
 MENU]
 
 
 
 
 Information