Samsung Syncmaster 320tsn User Manual

							 
 
 
1) Safety Screen 
- Eliminates the afterimages that can result when the selected display stays in Pause mode for an extended period of 
time. You can set the repeat cycle timer by selecting the Interval by hour and Second by second. 
It can be set to Scroll, Pixel, Bar and Eraser by Screen Type.
The Input source of MagicInfo works only on MagicInfo model. 
The Input source of TV works only on TV model. 
Setting Second, you can set to 1, 2, 3, 4, 5 for Scroll Type and to 10, 20, 30, 40, 50 for Pixel, Bar, and 
Eraser Type.  
The Maintenance Control feature is available only for the displays whose power status is ON.
 Maintenance  
 
Video Wall 
1. Click on the Maintenance icon in the Main Icon column to display the Maintenance screen.
 
						

							 
 
 
 
 
1) Video Wall  
- A Video Wall is a set of video screens that are connected together, so that each screen shows a part of the whole 
picture or so that the same picture is repeated on each screen.
2) Video Wall (Screen divider) 
- The screen can be divided into. 
You can select a number of screens with a different layout when dividing. 
zSelect a mode from Screen divider. zSelect a display from Display Selection. zThe place will be set up by pressing a number in the selected mode.  zThe MDC program supplied by Samsung supports up to 5x5 LCD Displayes.
3) On / Off  
- Turns on/off the Video Wall function of the selected display. 
4) Format 
- The format can be selected to see a divided screen. 
zFull 
zNatural 
You may not operate this function in MagicInfo.
The Input source of TV works only on TV model. 
The Maintenance Control function is available only for the displays where the power status is ON.
Troubleshooting 
 
1.
The display you wish to control does not appear on the Power Control Info Grid 
- Check the connection of RS232C. (Check if it is properly connected to the Com1 port)
 
						

							 
 
 
 
 
  - Check the displays to see if any of the other displays connected have the same ID. If more than one displays have 
the same ID, those displays are not properly detected by the program due to data conflict.
- Check if the Display Set ID is a number between 0 and 25. (Adjust using the Display menu)  
Note :A Display Set ID must be a value between 0 and 25 . 
2. The display you wish to control does not appear on the other Control Info Grids 
- Check to see if the display power is ON. (You can check this in Power Control Info Grid)
- Check if you can change the input source of the display. 
3. The dialogue box appears repeatedly. 
- Check to see if the display you wish to control is selected. 
4. Both On Timer and Off Timer have been set but different time is showing.  
- Apply current time to synchronize the display clocks.
5. The remote may not function properly when you turn off the remote Function, disconnect the RS-232C cable, or exit 
the program in an Irregular manner. Rerun the program and turn the remote function again to Restore normal 
functions. 
 
This program may malfunction due to problems in communication circuits or interference from electronic 
appliances nearby.
Settings Value Display In Multiple Display Mode 
 
 
 
When there are more than one displays connected, the settings values are displayed as follows.
1. No selection: Displays the Factory Default Value.
2. Selected one display: Fetches and displays the settings value for the selected display.
3. Selected one display (ID1) and add another display (ID3): The program, which was displaying the settings value of 
ID 1, fetches and displays the value of ID3.
4. Selected all sets using Select All: Returns to the Factory Default Value.
 
						

							Downloaded from ManualMonitor.com Manual± 
						

							Downloaded from ManualMonitor.com Manual± 
						

							Downloaded from ManualMonitor.com Manual± 
						

							Downloaded from ManualMonitor.com Manual± 
						

							Downloaded from ManualMonitor.com Manual± 
						

							Downloaded from ManualMonitor.com Manual± 
						

							Downloaded from ManualMonitor.com Manual±