Samsung Syncmaster 2233sw User Manual

Your Monitor
Initial Settings
Select the language using the up or down key.
The displayed content will disappear after 40 seconds.
Turn the Power button off and on. It will be displayed again.
It can be displayed up to three (3) times. Make sure to adjust the res\
olution of your PC before
reaching the maximum count.
 Note
The resolution displayed on the screen is the optimal resolution for thi\
s product.
Adjust your PC resolution so that it is the same as the optimal resoluti\
on for this product....

 Note
You can configure the customized key for a required function via  Setup >
Customized Key. Adjust buttons [ ]
These buttons allow you to adjust items in the menu. Enter button [ ]
Activates a highlighted menu item.
Push the  , then selects the video signal while the OSD is off. (When
the   button is pressed to change the input mode, a message appears in
the upper left of the screen displaying the current mode -- analog or di\
gital
input signal.)  Note
If you select the digital mode, you must...

POWER port
Connect the power cord for your monitor to the POWER port on the back of\
the monitor.
DVI IN port
Connect the DVI Cable to the DVI IN port on the back of your monitor.
RGB IN port
Connect the D-sub cable to the 15-pin, RGB IN port on the back of your m\
on-
itor.
Kensington Lock
The Kensington lock is a device used to physically fix the system when u\
sing
it in a public place. (The locking device has to be purchased separatel\
y.) For
using a locking device, contact where you purchase it....

Cable holding ring
• Fix the cables using the holding ring, as shown in the figure.
Introduction
13 

Connections
Connecting Cables
 Connect the power cord for your monitor to the power port on the back o\
f the monitor.
Plug the power cord for the monitor into a nearby outlet.  Use a connection appropriate for your computer.
 Using the D-sub (Analog) connector on the video card.
• Connect the signal cable to the 15-pin, D-sub port on the back of your m\
onitor. [RGB IN]
 Using the DVI (Digital) connector on the video card.
• Connect the DVI Cable to the DVI IN Port on the back of your Monitor. [DVI IN]...

Using the Stand
Folding the base
 Note
.
Attaching a Base This monitor accepts a 100 mm x 100 mm VESA-compliant mounting interface\
 pad. A. Monitor
B. Mounting interface pad (Sold separately)
1. Turn off your monitor and unplug its power cord.
2. Lay the LCD monitor face-down on a flat surface with a cushion beneath i\
t to protect the
screen.
3. Remove four screws and then remove the stand from the LCD monitor.
4. Align the mounting interface pad with the holes in the rear cover mounti\
ng pad and...

•
For wall mounts that do not comply with VESA standard screw specifica-
tions, the length of the screws may differ depending on their specificat\
ions.
• Do not use screws that do not comply with the VESA standard screw
specifications.
Do not fasten the screws too tightly, as this may damage the product or
cause the product to fall, leading to personal injury.
Samsung is not liable for these kinds of accidents.
• Samsung is not liable for product damage or personal injury when a non-
VESA or...

Using the Software
Monitor Driver
 Note
When prompted by the operating system for the monitor driver, insert the\
 CD-
ROM included with this monitor. Driver installation is slightly differen\
t from one
operating system to another. Follow the directions appropriate for the o\
per-
ating system you have.
Prepare a blank disk and download the driver program file at the Interne\
t web
site shown here.
Internet web site :
http://www.samsung.com/ (Worldwide) Installing the Monitor Driver (Automatic)
1....

 Note
This monitor driver is under certifying MS logo, and this installation d\
oesnt damage your
system.
The certified driver will be posted on Samsung Monitor homepage.
http://www.samsung.com/
Installing the Monitor Driver (Manual) Microsoft®
 Windows Vista™‚ Operating System
1. Insert your Manual CD into your CD-ROM drive.
2. Click  (Start) and Control Panel. Then, double-click on Appearance and Perso\
nal-
ization. 3. Click Personalization and then Display Settings.
4. Click Advanced Settings.......

If the message Windows needs... is displayed, as shown in the figure b\
elow, click
Continue.
 Note
This monitor driver is under certifying MS logo, and this installation d\
oesnt damage your
system.
The certified driver will be posted on Samsung Monitor homepage.
6. Click Update Driver... in the Driver tab. 7.
Check the Browse my computer for driver software checkbox and click L\
et me pick
from a list of device drivers on my computer. 8. Click Have Disk...” and select the folder (for example,...