Samsung Series 7 User Guide
Here you can view all the pages of manual Samsung Series 7 User Guide. The Samsung manuals for Television are available online for free. You can easily download all the documents as PDF.
Page 41
41 Preparations 1 1 Preparations zRS232C cable Connector: 9-Pin D-Sub to Stereo Cable LAN Cable zPin assignment -P1--P1- -P2--P2- Female Rx Tx Gnd 2 3 5-------->
Page 42
42 Preparations 1 1 Preparations zConnector: RJ45 Direct LAN cable (PC to HUB) Cross LAN cable (PC to PC) Signal P1 P2Signal TX+ 1 1TX+ TX- 2 2TX- RX+ 3 3RX+ RX- 6 6RX- Signal P1 P2Signal TX+ 1 3R X+ TX- 2 6RX- RX+ 3 1TX+ RX- 6 2TX - RJ45 MDC RJ45 MDC HUB P1 P1 P2 P2 RJ45 MDCP1P2
Page 43
43 Preparations 1 1 Preparations 1.6.2 Connection zConnection 1 zConnection 2 RS232CINOUTRS232CINOUTRS232CINOUTRS232CINOUT RJ45RJ45
Page 44
44 Preparations 1 1 Preparations zConnection 3 RS232COUT RJ45RS232CIN OUTRS232CINOUTRS232CINOUT
Page 45
45 Preparations 1 1 Preparations 1.6.3 Control Codes Viewing control state (Get control command) Controlling (Set control command) Command zIssued IDs can be displayed in hexadecimals. However, ID 0 must be displayed as 0xFF. zAll communications take place in hexadecimals. The checksum is calculated by adding up all values except the header. If a checksum adds up to be more than 2 digits as shown below (11+FF+01+01=112), the first digit is removed. E.g. Power On & ID=0 Header Command IDData length...
Page 46
46 Preparations 1 1 Preparations zTo control all devices connected by a serial cable simultaneously irrespective of IDs, set the ID as "0xFE" and transmit commands. Commands will be executed by each device but ACK will not respond. Power control zFunction A TV/monitor can be powered on and off using a PC. zViewing power state (Get Power ON / OFF Status) zSetting power ON/Off (Set Power ON / OFF) "Power": Power code to be set on a TV/monitor 1: Power ON 0: Power OFF zAck...
Page 47
47 Preparations 1 1 Preparations Volume control zFunction The volume of a TV/monitor can be adjusted using a PC. zViewing volume state (Get Volume Status) zSetting the volume (Set Volume) "Volume": Volume value code to be set on a TV/monitor (0-100) zAck "Volume": Volume value code to be set on a TV/monitor (0-100) zNak "ERR": A code showing what error has occurredHeader Command IDData length Checksum 0xAA 0x12 0 Header Command IDData length Data Checksum 0xAA 0x12 1...
Page 48
48 Preparations 1 1 Preparations Input source control zFunction The input source of a TV/monitor can be changed using a PC. zViewing input source state (Get Input Source Status) zSetting the input source (Set Input Source) "Input Source": An input source code to be set on a TV/monitor †DVI_video, HDMI1_PC and HDMI2_PC cannot be used with the Set command. They only respond to "Get" commands. †This model does not support BNC, S-Video, HDMI1, HDMI1_PC, HDMI2, HDMI2_PC, and DisplayPort....
Page 49
49 Preparations 1 1 Preparations zNak "ERR": A code showing what error has occurred Screen zFunction The screen mode of a TV/monitor can be changed using a PC. Screen mode cannot be controlled when the Video Wall function is enabled. This control can only be used on models that include a TV. zViewing screen status (Get Screen Mode Status) zSetting the picture size (Set Picture Size) "Screen Mode": A code that sets the TV/monitor status zAck "Screen Mode": A code that sets the...
Page 50
50 Preparations 1 1 Preparations Screen size control zFunction The screen size of a TV/monitor can be changed using a PC. zViewing the screen size (Get Screen Size Status) zAck "Screen Size": TV/monitor screen size (range: 0 – 255, unit: inch) zNak "ERR": A code showing what error has occurredHeader Command IDData length Checksum 0xAA 0x19 0 Header Command ID Data length Ack/Nak r-CMD Val1Checksum0xAA 0xFF 3‘A’ 0x19 "Screen Size" Header Command ID Data length Ack/Nak r-CMD...