Samsung Sdr3102 N Manual

							English _61
Setting the Port
1. Use the up/down buttons (▲▼) in  window to 
move to , and press [ENTER] 
button.
2.  Select .
3.  Use direction buttons (
▲▼_ +) to move to a desired 
item, and set the value.
•	 Protocol Type : Select the protocol type between TCP and 
UDP.
 
- TCP : If compared to UDP, TCP connection is more stable 
but slow. Recommended for Internet connection.
 
- UDP : If compared to TCP, UDP connection is less stable but fast. Recommended for use in LAN 
environment.
 
`If selected UDP, selections of Device Port,  UDP Port and Unicast/Multicast are activated.
 
`If setting the connection mode to PPPoE, you cannot select UDP for the protocol type.
•	 Device Port : Initially,  is set. It increases / decreases by 5.
 
- TCP: It has better stability and lower speed when compared to UDP, and recommended for internet 
environments.
•	 UDP Port : Initially,  is set. It increases / decreases by 160.
•	 Unicast/Multicast : Select one between UDP-Unicast and UDP-Multicast.
 
If selected Multicast, Multicast IP and TTL are activated.
 
- UDP- Unicast : Transfers data packet to an individual client.
 
- UDP-Multicast : Allows data communication to multiple clients causing no\
 additional traffic to the network.
•	Multicast IP Address : User can directly input.
•	 Multicast TTL : Select from 0 ~ 255. Initial value for the TTL is set to .
•	 HTTP Port : Enter the port number for the Web Viewer. Initially, it is set to .
•	 Multi Browser Support : The Web Viewer can be used with a browser that supports the Silverlight.
 
The multi viewer can be used only if the HTTP port is set to 80, protocol type is TCP and device ports range 
within 4505-4530. 
 
This is for the Siliverlight’s security purposes.
•	 Secure Video Transmission: Determine the network video transmission data is encrypted \
or not.  
Encrypt: ON, Not Encrypt: OFF.
If you set the secure video transmission mode, the max bandwidth performance will be limited\
.
When ON is selected, multi browser is not supported.
4.  When the protocol setup is done, press .
Connection ModePortInterface
 Protocol Type 
TCP
  
Device Port  4520 ~ 4524
  
UDP Port  8000 ~ 8160
  Unicast/Multicast 
Unicast
  Multicast IP 
Address  224.126.63.1
  
Multicast TTL   5
  
HTTP  Port  80
  
Secure Video Transmission           ON                  OFF
* Multi Browser Support:
 Device Port 4505~4530, HTTP Port 80
 OK  Cancel
 MAIN MENU  
						

							62_ main menu
Notification
 
J 
`In a multi-browser environment, the < HTTP Port> should be set to 80 (private port).  
Select one between 4505 and 4530 for RTSP
•	 Network Overview
POWER     REC     NETWORKPOWER     REC     NETWORK
Internet
Local PC DVR 1
Router (External IP: 109.112.92.133, 
Local IP: 192.168.1.1 Cable/ADSL  
Modem
DVR 2 DDNS Server 
(www.samsungipolis.com)
System
DVR 1
DVR 2
WEB RTSP WEBRTSP
IP 192.168.1.200 192.168.1.200192.168.1.202 192.168.1.202
Protocol TCPTCPTCP TCP
Private Port 804520~4524 814525~4529
Public Port 804520~4524 814525~4529
Connection ModeInterfacePort
 
IP Type  Static
  
Transfer Bandwidth 2Mbps
 OK  Cancel

 IP
 Address  192.168.1.200
  Gateway 
192.168.1.1
  Subnet Mask 
255.255.255.0
  DNS 
Manual 168.126.63.1
Connection ModeInterfacePort
 
IP Type  Static
  
Transfer Bandwidth 2Mbps
 OK  Cancel

 IP
 Address  192.168.1.202
  Gateway 
192.168.1.1
  Subnet Mask 
255.255.255.0
  DNS 
Manual 168.126.63.1
Connection ModePortInterface
 Protocol Type 
TCP
  
Device Port  4520 ~ 4524
  
UDP Port  8000 ~ 8160
  Unicast/Multicast 
Unicast
  Multicast IP 
Address  224.126.63.1
  
Multicast TTL   5
  
HTTP  Port  80
  
Secure Video Transmission           ON                  OFF
* Multi Browser Support:
 Device Port 4505~4530, HTTP Port 80
 OK  Cancel
Connection ModePortInterface
 Protocol Type 
TCP
  
Device Port  4525 ~ 4529
  
UDP Port  8000 ~ 8160
  Unicast/Multicast 
Unicast
  Multicast IP 
Address  224.126.63.1
  
Multicast TTL   5
  
HTTP  Port  81
  
Secure Video Transmission           ON                  OFF
* Multi Browser Support:
 Device Port 4505~4530, HTTP Port 80
 OK  Cancel
main menu  
						

							English _63
•	1st Set Port Forwarding Setting
Port Forwarding is 4520~4524 
(4520, 4521, 4522, 4523, 4524)
SDR-5102192. 168. 1. 200
Port Forwarding is 80 
SDR-5102
•	 2nd Set Port Forwarding Setting
Port Forwarding is 4525~4529 
(4525, 4526, 4527, 4528, 4529)
SDR-5102
Port Forwarding is 81
SDR-5102
192. 168. 1. 200
192. 168. 1. 202
814525452581
192. 168. 1. 202
 MAIN MENU  
						

							64_ main menu
Connecting and Setting the Network
Networking may differ from the connection method, check your environment before setting the connection mode.
when no router is used
•	Static mode
 
- Internet connection : Static PPPoE, leased line, and LAN environments allows connection between the DVR 
and remote user.
 
- DVR Network Settings : Set the  in 
 menu of the connected DVR to .
 
`Consult your network manager for IP Address, Gateway and 
Subnet Mask.
•	 DHCP mode
 
- Internet connection : Connect the DVR directly to a cable 
modem, DHCP PPPoE modem or FTTH network.
 
- DVR Network Settings : Set the  in 
 menu of the connected DVR to .
•	 PPPoE mode
 
- Internet connection : An PPPoE modem is directly connected to the DVR, where the PPPoE connection 
requires user ID and password.
 
- DVR Network Settings : Set the  in 
 menu of the connected DVR to .
 
`< ID> and  should be the same to the PPPoE user 
information.  
If you don’t know the ID and password, consult your PPPoE service 
provider.
Connection ModeInterfacePort
  
IP Type  Static
  
Transfer Bandwidth 2Mbps
 OK  Cancel

 IP
 Address  192.168.1.200
  Gateway 
192.168.1.1
  Subnet Mask 
255.255.255.0
  DNS 
Manual 168.126.63.1
Connection ModeInterfacePort
 
IP Type  PPPoE
  
Transfer Bandwidth 600kbps
 OK  Cancel

 IP
 Address  192.168.1.200
  Gateway 
192.168.1.1
  Subnet Mask 
255.255.255.0
  DNS 
Manual 168.126.63.1
  
ID ID
  Password 
************
main menu  
						

							English _65
when a router is used
 
J 
`To avoid IP address conflict with the DVR's static IP, check followings :
•	 Setting the DVR with a static IP
 
-  
Internet connection : You can connect the DVR to a router which is connected to an PPPoE/Cable modem 
or a router in a Local Area Network (LAN) environment.
•	 Setting the DVR Network
1.  Set the  in  menu of the connected DVR to .
2.  Check whether the set IP address is in the static IP range provided by the Broadband Router.
 
IP Address, Gateway, and Subnet Mask : Consult your network manager.
 
`Check whether the set IP address is in the static IP range provided by the Broadband Router.
 
J 
`If a DHCP server is configured with starting address (192.168.0.100) and end addres\
s (192.168.0.200), you should 
set the IP address out of the configured DHCP range (192.168.0.2 ~ 192.\
168.0.99 and 192.168.0.201 ~ 
192.168.0.254).
3.  Check the Gateway address and subnet mask are equal to those set in the Broadband Router.
•	 Setting the DHCP IP Address of the Broadband Router
1.  To access the Broadband Router’s configurations, open a web browser on the local PC that is connected 
to the Broadband Router and enter the router’s address (ex : http://192.168.1.1).
2.  At this stage, make the local PC's windows network configurations to the\
 below example :
 
Ex)   IP Address : 192.168.1.2 
Subnet Mask : 255.255.255.0 
Gateway : 192.168.1.1
 
- Once connected to the Broadband Router, it prompts with password. While entering nothing to the User 
Name field, enter “admin” into the password field and press  to access the router configurations.
 
- Access the router’s DHCP configuration menu and set its DHCP server activation, and provide the start and 
end address.
 
Set the start address (192.168.0.100) and end address (192.168.0.200).
 
M 
`Above steps may differ from the router devices depending on the manufacturer.
 MAIN MENU  
						

							66_ main menu
•	Setting Router’s Port Forwarding
1.  Set the protocol to .
2.  External Port Range : Enter the TCP Port set in the 
 
 in  menu of the connected DVR. 
If more than one DVRs are connected to the router, the 
TCP port can be different.
3.  Internal PC IP Address : Enter the IP address set to the 
 in  menu of the connected 
DVR.
4.  Internal Port Range : Set the same to the “External Port 
Range”.
 
M   
`Above steps may differ from the router devices depending on the manufacturer.  
Port forwarding is required when you want to access the DVR connected to the r\
outer from outside of the router’s 
network.
DDNS
You can set the DDNS site for a remote user’s network connection.
Using the mouse may help make setup easier.
1.  Use the up/down buttons (▲▼) in  window to 
move to , and press [ENTER] button.
 
DDNS Setup screen appears.
2.  Use the virtual keyboard to enter the .
 
`Refer to “Using Virtual Keyboard”. (Page 35)
 
`If selected  input fields are deactivated.
 
`If selected , the server name field is disabled.
•	 DDNS Site : Set whether to use DDNS or not, and select 
the DDNS site if enabled.
•	 Server Name : Enter the server name of the selected DDNS site.
•	 Product ID : Enter the product ID which was registered to the DDNS site.
•	 Quick Connect : Appears if the  is set to .
 
To use this feature, connect the DVR to a UPnP router and set to .
 
M 
`If the quick connect setup has been cancelled while progressing, it is automatically set to .
3.  When the DDNS setup is done, press .
  OK  Cancel
DDNS
 DDNS Site 
iPOLiS
  
Server Name  www.samsungipolis.com
  
Product ID 
  Quick Connect 
Not Used Use
  DDNS Host Address 
http://www.samsungipolis.com/
Connection ModePortInterface
 Protocol Type 
TCP
  
Device Port  4520 ~ 4524
  
UDP Port  8000 ~ 8160
  Unicast/Multicast 
Unicast
  Multicast IP 
Address  224.126.63.1
  
Multicast TTL   5
  
HTTP  Port  80
  
Secure Video Transmission           ON                  OFF
* Multi Browser Support:
 Device Port 4505~4530, HTTP Port 80
 OK  Cancel
main menu  
						

							English _67
DDNS Setting
DDNS is a short form of Dynamic Domain Naming System. 
DNS (Domain Name System) is a service that routes a domain name consisting of user friendly characters  
(ex : www.google.com) to an IP address consisting of numbers (64.233.189.104). 
DDNS (Dynamic DNS) is a service that registers a domain name and the floating IP address with the DDNS 
server so that the domain name can be routed to the IP address even if the IP is changed in a dynamic IP 
system.
•	Setting DDNS in the DVR
Set  in the  menu of the connected DVR to the following :
Ex)   Protocol Type : TCP
 
Device Port : 4520~4524 
DDNS Site : iPOLiS
•	 DDNS Settings of the Router
Select the corresponding menu for the network transfer protocol of the router.
•	 SETTING UP SAMSUNG iPOLiS DDNS
Go to Your PC
1.  Open your browser and go to http://www.samsungipolis.com and click .
2.  You first need to create an account.
 
Click .
3.  Follow the account registration instructions on the website.
4.  After completing the account registration, login to your 
account.
5.  Add your DVR to your account. Click .
6.  Create a name(Product ID) for your DVR. Use 4 to 20 
alphanumeric characters without spaces. Select 
classification, model number of the DVR and click 
.
7.  After registration, you should see your product in the list.
 MAIN MENU  
						

							68_ main menu
Go back to DVR
1. From network tab, click on .
2.  Under DDNS Site, select .
3.  Under Product ID, enter the product ID you created on the 
Samsung iPOLiS website.
 
Under Quick Connect, select  and click .
 
M 
`If the connection was not successful, your router may not be 
supporting UPNP.  
For more information on enabling UPNP on your router, please 
see Router manual.
  OK  Cancel
DDNS
 DDNS Site 
iPOLiS
  
Server Name  www.samsungipolis.com
  
Product ID 
  Quick Connect 
Not Used Use
  DDNS Host Address 
http://www.samsungipolis.com/
 OK  Cancel
DDNS
 DDNS Site 
iPOLiS
  
Server Name  www.samsungipolis.com
  
Product ID sdr5102dhome
  Quick Connect 
Not Used Use
  DDNS Host Address 
http://www.samsungipolis.com/srd1673dhome
 OK  Cancel
DDNS
 DDNS Site 
iPOLiS
  
Server Name  www.samsungipolis.com
  
Product ID srd1673dhome
  Quick Connect 
Not Used Use
  DDNS Host Address 
http://www.samsungipolis.com/srd1673dhome
Connection
OK
Quick Connect Success
Network
Logout 
Return
Connection Mode
DDNS
Live Transfer
Mailing Service
main menu  
						

							English _69
Live Transfer
Sets the quality of the image that is transferred from the DVR to the network.
Using the mouse may help make setup easier.
1. Use the up/down buttons (▲▼) in  window to 
move to , and press [ENTER] button.
 
The Live Transfer window appears.
2.  Use direction buttons (
▲▼_ +) to move to a desired 
item, and set the value.
•	 Resolution: Shows the selected network profile’s resolution 
setting.
•	 Quality: Shows the selected network profile’s image quality 
setting.
3.  When the live transfer is done, press .
Live Transfer
  OK  Cancel Previous/Next Page
 
CH  Resolution 
 
Quality 

  1  CIF 
 Low 

  2  CIF 
 Low 

  3  CIF 
 Low 

  4  CIF 
 Low 

  5  CIF 
 Low 

  6  CIF 
 Low 

  7  CIF 
 Low 

  8  CIF 
 Low 

 MAIN MENU  
						

							70_ main menu
Mailing Service
You can send an e-mail to a DVR-registered user at a specific time interval, or if an event occurs.
 
M 
`If an event occurs with a channel where the camera’s video is set to  or the remaining recording count is set 
to , only the text notification will be sent to the applicable email address.
 
J 
`If you set the interval of the e-mail notice too short, the e-mail server may consider it as spam that will not be 
transferred normally.
SMTP Setting
Sets the SMTP mail server.
Using the mouse may help make setup easier.
1.  Use the up/down buttons (▲▼) in  window to 
move to , and press [ENTER] button.
2.  Select .
 
You will see the SMTP setting window.
3.  Use direction buttons (
▲▼_ +) to move to a desired 
item, and set the value.
•	 ServerType : Displays the connected server type.
•	 Server Address : Enter a server to connect to.
•	 Port : Sets the communication port.
•	 Use Authentication : Check this if the SMTP server uses 
user authentication.
 
The account input box will be activated.
•	 ID : Enter a user to use authentication when connecting to the SMTP server\
.
•	 Password : Enter the password of the SMTP server user.
•	 Secure Transfer : Select one from  and .
•	 Sender Address : Use the virtual keyboard to enter the sender’s e-mail address.
 
`Refer to “Using Virtual Keyboard”. (Page 35)
•	 E-mail Test : Conducts the test on the server settings.
4.  When the SMTP setup is done, press .
Mailing ServiceSMTPEvent 
  OK  Cancel
Use Authentication Group
Recipient
 ServerType 
SMTP mail Server
  
Server Address  
  Port 
25
ID 
Password 
  Secure Transfer 
Never
  
Sender Address    ex. [email protected]
E-mail Test
main menu