Samsung Sde 5001 N Manual

							English _11
 OVER
REMOTE CONTROL
Using the numeric buttons
CHANNEL 1
						

							12_ installation
Please take note of the followings before using this product.
• Do not use the pr
• Do not spill water or liquid in the connection part of the pr
• Do not impose the system to excessive shock or for
• Do not pull out the power plug for
• Do not disassemble the pr
• Do not exceed the rated input/output range.
• Use a certified power cor
• For the pr
CHECKING THE INST
Samsung Digital Video Recor
state-of-art security device, and contains mass storage har
disk\(s\) and critical cir
When the temperatur
may br
pay attention to the following r
installation.
The followings ar
1. 
2. 
3. 
suitable space or install a ventilating opening for air cir
4. 
top.
5. 
cir
6. 
40
						

							English _13
 CONNECTING WITH OTHER DEVICE
CONNECTING THE VIDEO, AUDIO, AND MONITOR
  M  Do not connect UTP camera and BNC camera simultaneously
CONNECTING THE CAMERA
Equipped with the IR LED and the illumination sensor
The camera is suitable for both inter
connecting with other device
NETWORK
USBAUDIO IN 1
AUDIO IN 2 VIDEO IN 2 VIDEO IN 1VIDEO OUTCONSOLE
CAMERA POWER12V
12VSENSOR POWERGGG
COM1 4 3 2 1DVR & CAMERA POWER VGA
AUDIO OUT
1 - 12 CH 13 - 16 CH5 1
6 2
7 3
8 4
139
14 10
15 11
16 12
ALARM INALARM OUT


SEB-1005R
b
c
 
						

							14_ connecting with other device
connecting with other device
Name
Camer
GrooGroove that is used to fit the camera bracket.
There are two grooves; one on the top and one on the bottom.
IR LEDThese infrared LEDs are controlled by the illumination sensor
LensFocal length of 3.8mm enables you to cover relatively longer range of monitoring.
Illumination SensorDetects incoming light to control the IR LED.
DVR Connection
CableConnect the cable directly to the DVR without using a particular power cable.
Y
RJ-45 cable to connect to a remote camera.
RJ-45 Cable
Installing the camera \(SEB-1005R\)
The camera can be installed on the wall, ceiling, shelf or a desir
1. Select a position wher
  Make sure the selected position can sustain the weight of the camera.
2. Use the scr
the wall or ceiling.
3. Place the camera on the selected position and fit the hole either on
the top or the bottom of the camera into the fixing bolt of the
bracket, and tur
  J  Y
the cable connectors may be wet with moisture or pile up with impurities.
CVBS+12V
CVBS-
N.C
GNDGND\(A
GND
M4 X L15 sized 
scr
w 
						

							English _15
 CONNECTING WITH OTHER DEVICE
Camera Bracket
The camera bracket can be used to install the camera on the wall, ceiling or shelf.
Camera Bracket Specification
Name
UseIndoor
InstallationW
Dimensions57\(W\) x 47.2\(H\) x 100.5\(L\) mm/
2.25\(W\) x 1.86\(H\) x 3.95\(L\) inch
W130g \(0.29 lbs\)
Oper-10C ~ 50C \(14F ~ 122F\)
AccessoriesSCREW \(M4 X L15\) :
Adjusting the Camera Bracket
1. Choose an installation site that can suf
the equipments to be installed.
2. Attach the camera bracket to the wall using the supplied scr
\(M4 X L15\). 4x15 sized scr
3. Adjust the camera to target the video location and tighten the camera
bracket handle on the camera bracket. Install the camera on to the
male scr
4. Loosen the handle by tur
camera position. Tighten the handle, tur
camera in position.
5. Connect the camera cable to the camera.
Handle 
						

							16_ connecting with other device
connecting with other device
Installing the camera \(SED-1001R\)
Pr
Ensur
  
Select an installation site \(ceiling or wall\) that can endur
  
Stuck-in or peeled-of
1. Hold down the bottom lock lever while r
other hand.
2. Pr
the bracket counter clockwise to r
3. Use the pr
position \(ceiling or wall\).
  Ensure that the  label on the bracket faces the
direction for camera monitoring.
Wiring Cover
 
						

							English _17
 CONNECTING WITH OTHER DEVICE
4. Arrange the cables thr
If you intend to drill a hole in the installation site for the wiring purpose, r
hole. Arrange the cables thr
If you intend to arrange the cables without drilling a hole, use the empty arCAMERA
FRONT> label side for the wiring purpose.
5. Mount the main unit onto the bracket.
Align the marking hole of the main unit with the  
label of the bracket, and turLOCK> dir
6. Adjust the lens in a desir
For adjusting the lens dirAdjusting the monitoring
dir
						

							18_ connecting with other device
connecting with other device
CONNECTING THE USB
1. By factory default, a USB port is pr
2. Y
3. If a USB HDD is connected to the system, rMenu > Setting the Device > 
Storage Device
						

							English _19
 CONNECTING WITH OTHER DEVICE
CONNECTING THE NETWORK
Connecting to Inter
Connecting to the Inter
NETWORK
USBAUDIO IN 1
AUDIO IN 2 VIDEO IN 2 VIDEO IN 1VIDEO OUTCONSOLE
CAMERA POWER12V
12VSENSOR POWERGGG
COM1 4 3 2 1DVR & CAMERA POWER VGA
AUDIO OUT
1 - 12 CH 13 - 16 CH5 1
6 2
7 3
8 4
139
14 10
15 11
16 12
ALARM INALARM OUT
Windo
Netw
BacHub/Switc
Hub/Switc RJ-45 Ether
\(Dir
INTERNET
NETWORK
USBAUDIO IN 1
AUDIO IN 2 VIDEO IN 2 VIDEO IN 1VIDEO OUTCONSOLE
CAMERA POWER12V
12VSENSOR POWERGGG
COM1 4 3 2 1DVR & CAMERA POWER VGA
AUDIO OUT
1 - 12 CH 13 - 16 CH5 1
6 2
7 3
8 4
139
14 10
15 11
16 12
ALARM INALARM OUT
RouterxDSL or Cable 
ModemxDSL or Cable 
Modem
Exter
PC
DDNS Ser
\(Data Center\)
INTERNET 
						

							20_ connecting with other device
connecting with other device
Connecting to Inter
NETWORK
USBAUDIO IN 1
AUDIO IN 2 VIDEO IN 2 VIDEO IN 1VIDEO OUTCONSOLE
CAMERA POWER12V
12VSENSOR POWERGGG
COM1 4 3 2 1DVR & CAMERA POWER VGA
AUDIO OUT
1 - 12 CH 13 - 16 CH5 1
6 2
7 3
8 4
139
14 10
15 11
16 12
ALARM INALARM OUT
Windo
Netw
Phone\(ADSL\) Line
ADSL MODEM
Hub/Switc RJ-45 Ether
\(DirINTERNET