Samsung SCX 4300 User Manual

Getting started
2.5
3Squeeze the paper width guide, as shown and slide it to 
the stack of paper until it lightly touches the side of the 
stack.
NOTES:
• Do not push the paper width guide far enough to cause the 
materials to warp.
• If you do not adjust the paper width guide, it may cause 
paper jams.
Making connections
1Connect a USB cable to the USB connector on your 
machine. You need to buy a USB 2.0 compliant cable that 
is not longer than 3 m.
2Connect the other end of the cable to the USB port...

Getting started
2.6
Setting up the machine system
Overview of control panel menus
The control panel provides access to various menus to set up 
the machine or use the machine’s functions. They can be 
accessed by pressing 
Menu. 
Refer to the following diagram.
Reduce/Enlarge
Darkness
Original Type
Special Copy
Off
Clone
Auto Fit
ID Card Copy
2 UP
Poster
Toner Save
Paper SettingPaper Size
Paper Type
Copy SetupDefault-Change
Timeout
Report
Machine SetupLanguage
Power Save
USB mode
MaintenanceClean Drum...

Getting started
2.7
Printer software overview
Supplied printer software
You must install the printer software using the supplied printer 
driver CD after you have set up your machine and connected it 
to your computer. For details, see the 
Software Section. 
The printer driver CD provides you with the following software:
Programs for windows
To use your machine as a printer and scanner in Windows, you 
must install the MFP driver. You can install selectively or all the 
following components: 
•
Printer...

Getting started
2.8
System requirements
Before you begin, ensure that your system meets the minimum 
requirements.
Windows
Your machine supports the following Windows operating systems. 
NOTE: 
• Internet Explorer 5.0 or higher is the minimum requirement 
for all Windows operating systems.
• Users who have an administrator right can install the 
software.
Operating 
SystemRequirement (recommended)
CPURAMfree HDD 
space
Windows 
2000Pentium II 400 MHz 
(Pentium III 933 MHz)64 MB 
(128 MB)650 MB
Windows...

Loading original documents and paper
3.1
3Loading original 
documents and paper
This chapter introduces you to how to load documents and print 
materials into your machine.
This chapter includes:
• Loading document
• Selecting print materials
• Loading paper
• Setting the paper size and type
• Selecting an output location
Loading document
You can use the document glass to load an original document 
for copying and scanning.
1Lift and open the document cover.
2Place the document face down on the document...

Loading original documents and paper
3.2
Selecting print materials
You can print on a variety of print materials, such as plain 
paper, envelopes, labels, and transparencies. Always use print 
materials that meet the guidelines for use with your machine. 
Paper that does not meet the guidelines outlined in this user’s 
guide may cause the following problems:
• Poor print quality
• Increased paper jams
•Premature wear on the machine.
Properties, such as weight, composition, grain, and moisture 
content,...

Loading original documents and paper
3.3
Paper size supported in each mode
Envelope
(continued)Envelope C6 114 x 162 mm
(4.48 x 6.37 
inches)60 to 90 
g/m2 (16 to 
24 lb)1 sheet of 
paper for 
the manual 
feeder
Transparency Letter, A4 Refer to the Plain 
paper section138 to 148 
g/m
21 sheet of 
paper for 
the manual 
feeder
Labels Letter, Legal, 
Folio, A4, JIS 
B5, ISO B5, 
Executive, 
A5, A6Refer to the Plain 
paper section120 to 150 
g/m
2 (32 to 
40 lb)1 sheet of 
paper for 
the manual 
feeder
Card...

Loading original documents and paper
3.4
Guidelines for special materials
Paper TypeGuidelines
Envelopes • Successful printing on envelopes depends upon the 
quality of the envelopes. When selecting envelopes, 
consider the following factors:
- Weight: The weight of the envelope paper should 
not exceed 90 g/m
2 (24 lb) or jamming may 
occur.
- Construction: Prior to printing, envelopes should 
lie flat with less than 6 mm (0.25 inches) curl, and 
should not contain air.
- Condition: Envelopes should not...

Loading original documents and paper
3.5
Loading paper
In the paper input tray
Load the print material you use for the majority of your print 
jobs in the paper input tray. The paper input tray can hold a 
maximum of 250 sheets of 20 lb (
80 g/m2) plain paper. 
To load paper, pull open the paper input tray and load paper 
with the side to be printed on face down.
You can load letterhead paper with the design side face down. 
The top edge of the sheet with the l o g o  s h o u l d  be  p l a c e d a t  t...

Loading original documents and paper
3.6
2Adjust the manual feeder guides to the width of the print 
material without bending it.
3After loading paper, you need to set the paper type and 
size for the manual feeder. See page 3.6 for copying or the 
Software Section for PC-printing.
NOTE: The settings made from the printer driver override the 
settings on the control panel.
4If you want to use the rear cover, open the rear cover.
Tips on using the manual feeder
• Print materials should be loaded face up...