Samsung Rm 25 Kgrs Owners Manual

21
INSTALLATION INSTRUCTIONS
INSTALLATION OF THE REFRIGERATOR
LEVELLING
If the front of the appliance is slightly higher than the rear, the door can be opened and closed easier.
The appliance tilts down to the left.
Turn the left adjusting leg in the direction of
the arrow with a flat head screwdriver until
the appliance is level.
Loading Plan
The appliance tilts down to the right.
Turn the right adjusting leg in the direction of
the arrow with a flat head screwdriver until
the appliance is level.
• Be...

22
ADJUSTING THE HEIGHT BETWEEN THE DOORS
The doors will be uneven if the refrigerator is not level.
Case 1) Freezer door is lower than       
the refrigerator door.Insert a flat-blade screwdriver (-)  (
➀) into a slot of 
the control lever (➁), turn it clockwise and level the
refrigerator.
Case 2) Freezer door is higher than   
the fridge doorInsert a flat-blade screwdriver (-) (
➀) into a slot of
the control lever (➁), turn it clockwise and level 
the refrigerator.
Do not make small adjustments with...

INSTALLATION INSTRUCTIONS
ADJUSTING THE HEIGHT BETWEEN THE DOORS
23
Making small adjustments between doors.
If the door of fridge is lower than that of the freezer,
1) If you open the Fresh Select Zone Door (➀), you can see the hinge-mid (➁).
2) Insert enclosed hex wrench (
➂) into the shaft (
➃) of the hinge mid.
3) Please adjust the height difference between the doors turning the hex wrench (
➂) clockwise (          )
or counter clockwise (          ).
4) After adjusting the doors, please insert...

24
ADJUSTING THE HEIGHT BETWEEN THE DOORS
The adjuster in the Fresh Select Zone can be used in the same way.NOTE
If the Arctic Select Zone Door is lower than the Fresh Select Zone Door.
1) Locate the height-adjuster (➀) in the Arctic Select Zone.
Unscrew the four phillips screws (➁) slightly to loose the door.
2) Unscrew the adjuster-phillips screw (
➂) two times turns to rotate the adjuster.
3) Find the best adjuster-level to align the door gap.
After adjustment, tighten the screws (➁ & ➂) in reverse...

25
INSTALLATION INSTRUCTIONS
1) With the door closed,remove the upper hinge cover (➀) using a screwdriver, and then remove the
water tube by pressing the coupler-ring (➁) and pulling the water tube (
➂) away. Unscrew two phillips screws from the front leg cover.
Pull the front leg-cover down with both hands and remove it by lifting it up with the upper rib.
Then, disengage the lower hooks.
Removing the Freezer Door
•Lift the door straight up.
•Be careful not to pinch the water tubing and wire harness on...

26
4) Remove the door from the lower
hinge(
➇)carefully lifting the door(➈).5) Remove the phillips screw(➉)and two hex
head screws (   )from the lower hinge11
Removing the Freezer Door
REMOVING THE REFRIGERATOR DOORS
2) Disengage the hooks on the connector - cover (
➃) protecting the connector and open it.
Push the lever-hook (➄) on the connector and disconnect the wires.
3) Pull and open the latch (➅), and take off the door hinge (➆) along the arrow.
Be careful when removing the door to ensure that it...

27
INSTALLATION INSTRUCTIONS
REMOVING THE REFRIGERATOR DOORS
3) Removethe door from the lower hinge (
➃)by
lifting the door (
➄).
4) Remove the phillips screw (➅) and two hex
head screws (➆) from the lower hinge. 1) With the door closed, remove the upper hinge cover (➀) using a screwdriver.
2) Pull and open the latch (➁), and take off the door hinge (
➂) along the arrow.
Removing the Fridge Door
%&	


 

.

 

28
REMOVING THE REFRIGERATOR DOORS
How to disassemble/assemble the Arctic Select Zone Door
1) Open the Arctic Select Zone Door.
3) Locate the eight phillips screws in the Arctic Select Zone. To lift the door up, unscrew the eight
phillips screws(➀) four turns. Do not remove the screws (➀) out.
(You don’t need to unscrew the adjuster-phillips screw(➁ )2) Take out the box in the Arctic Select
Zone Door.
4) Remove the door carefully from the rail lifting up the
door with both hands.
To allow screw(➀) heads...

29
INSTALLATION INSTRUCTIONS
REMOVING THE REFRIGERATOR DOORS
How to disassemble/assemble the Fresh Select Zone Door
4) Remove the door carefully from the rail lifting up
the door with both hands.To allow screw(➀) heads
to pass through the rail holes. 3) Locate the eight phillips screws in the Fresh Select Zone. To lift the door up, unscrew the eight phillips
screws(➀) four turns. Do not remove the screws (➀) out.
(You don’t need to unscrew the adjuster-phillips screw(➁) 1) Open the Fresh Select Zone...

30
Reattaching the Freezer Door
REATTACHING THE REFRIGERATOR DOORS
1) Reattach a phillips screw (
➀) and two hex head
screws (➁) to the hinge completely.2) Place the hole in the bottom of the door (➃)
over the hinge (
➂).
3) Insert the upper hinge shaft (➄) into the hole (➅). After levelling between the hinge brackets (➆).
Reattach and close the latch (
➇) along the arrow.
Connect the water tube (➈) and the wires (
➉). Then, place the water tube(➈) on the hanger (   )
4) Put the connector (   ) in the...