Samsung Rm 25 Kgrs Owners Manual
Have a look at the manual Samsung Rm 25 Kgrs Owners Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 1705 Samsung manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
21 INSTALLATION INSTRUCTIONS INSTALLATION OF THE REFRIGERATOR LEVELLING If the front of the appliance is slightly higher than the rear, the door can be opened and closed easier. The appliance tilts down to the left. Turn the left adjusting leg in the direction of the arrow with a flat head screwdriver until the appliance is level. Loading Plan The appliance tilts down to the right. Turn the right adjusting leg in the direction of the arrow with a flat head screwdriver until the appliance is level. • Be careful when you open the door in full swing. It might come in contact with its adjacent units. CAUTION 1617.0 908 1391.0 630.6507 Front View Side View Door View To get the maximum energy efficiency, you had bet- ter give enough clearance of the back side. To get more space remove the box in the Freezer and the Fridge,the partition and the upper box in the Arctic Select Zone, the upper box in the Fresh Select Zone since it does not effect satisfactory ther- mal and mechanical characteristics. NOTE • Allow sufficient space to install the refrigerator on a flat surface. - If your refrigerator is not level, the internal cooling system may not work correctly. WARNING %& .
22 ADJUSTING THE HEIGHT BETWEEN THE DOORS The doors will be uneven if the refrigerator is not level. Case 1) Freezer door is lower than the refrigerator door.Insert a flat-blade screwdriver (-) ( ➀) into a slot of the control lever (➁), turn it clockwise and level the refrigerator. Case 2) Freezer door is higher than the fridge doorInsert a flat-blade screwdriver (-) ( ➀) into a slot of the control lever (➁), turn it clockwise and level the refrigerator. Do not make small adjustments with the control lever, Please refer to the next page. DIFFERENCE OF HEIGHT DIFFERENCE OF HEIGHT ➀DRIVER(-) ➀DRIVER(-) ➁CONTROL LEVER ➁CONTROL LEVER Please level the refrigerator first NOTE %& .
INSTALLATION INSTRUCTIONS ADJUSTING THE HEIGHT BETWEEN THE DOORS 23 Making small adjustments between doors. If the door of fridge is lower than that of the freezer, 1) If you open the Fresh Select Zone Door (➀), you can see the hinge-mid (➁). 2) Insert enclosed hex wrench ( ➂) into the shaft ( ➃) of the hinge mid. 3) Please adjust the height difference between the doors turning the hex wrench ( ➂) clockwise ( ) or counter clockwise ( ). 4) After adjusting the doors, please insert enclosed fastener-ring (➄) using a plier (➅) in the gap between the hinge-grommet (➆) and the hinge-mid ( ➇). The number of the fastener-ring to insert depends on the gap. When you turn counter clockwise ( ), the door goes up.NOTE Four fastener-rings are enclosed with the refrigerator.NOTE adjustment part %& .
24 ADJUSTING THE HEIGHT BETWEEN THE DOORS The adjuster in the Fresh Select Zone can be used in the same way.NOTE If the Arctic Select Zone Door is lower than the Fresh Select Zone Door. 1) Locate the height-adjuster (➀) in the Arctic Select Zone. Unscrew the four phillips screws (➁) slightly to loose the door. 2) Unscrew the adjuster-phillips screw ( ➂) two times turns to rotate the adjuster. 3) Find the best adjuster-level to align the door gap. After adjustment, tighten the screws (➁ & ➂) in reverse order. adjustment part Arctic Select Zone Fresh Select Zone - Rotate down the adjuster-face with +2.0number to reduce the door gap. - The number of the adjuster to rotate depends on the gap. Arctic Select Zone DoorFresh Select Zone Door gap ➁ ➀ ➂ CASE) The gap is about 2mm (0.08inch) as shown below. reference plane %& .
25 INSTALLATION INSTRUCTIONS 1) With the door closed,remove the upper hinge cover (➀) using a screwdriver, and then remove the water tube by pressing the coupler-ring (➁) and pulling the water tube ( ➂) away. Unscrew two phillips screws from the front leg cover. Pull the front leg-cover down with both hands and remove it by lifting it up with the upper rib. Then, disengage the lower hooks. Removing the Freezer Door •Lift the door straight up. •Be careful not to pinch the water tubing and wire harness on the door. •Place doors on a protected surface. NOTE REMOVING THE REFRIGERATOR DOORS FRONT LEG COVER RIB HOOK Removing the Front Leg Cover Do not cut the water tube. Separate it from the coupler.NOTE %& .
26 4) Remove the door from the lower hinge( ➇)carefully lifting the door(➈).5) Remove the phillips screw(➉)and two hex head screws ( )from the lower hinge11 Removing the Freezer Door REMOVING THE REFRIGERATOR DOORS 2) Disengage the hooks on the connector - cover ( ➃) protecting the connector and open it. Push the lever-hook (➄) on the connector and disconnect the wires. 3) Pull and open the latch (➅), and take off the door hinge (➆) along the arrow. Be careful when removing the door to ensure that it does not fall on you. %& .
27 INSTALLATION INSTRUCTIONS REMOVING THE REFRIGERATOR DOORS 3) Removethe door from the lower hinge ( ➃)by lifting the door ( ➄). 4) Remove the phillips screw (➅) and two hex head screws (➆) from the lower hinge. 1) With the door closed, remove the upper hinge cover (➀) using a screwdriver. 2) Pull and open the latch (➁), and take off the door hinge ( ➂) along the arrow. Removing the Fridge Door %& .
28 REMOVING THE REFRIGERATOR DOORS How to disassemble/assemble the Arctic Select Zone Door 1) Open the Arctic Select Zone Door. 3) Locate the eight phillips screws in the Arctic Select Zone. To lift the door up, unscrew the eight phillips screws(➀) four turns. Do not remove the screws (➀) out. (You don’t need to unscrew the adjuster-phillips screw(➁ )2) Take out the box in the Arctic Select Zone Door. 4) Remove the door carefully from the rail lifting up the door with both hands. To allow screw(➀) heads to pass through the rail holes.5) Slide the rail carefully to the inside. When you assemble the Arctic Select Zone Door, follow the contrary order.NOTE %& .
29 INSTALLATION INSTRUCTIONS REMOVING THE REFRIGERATOR DOORS How to disassemble/assemble the Fresh Select Zone Door 4) Remove the door carefully from the rail lifting up the door with both hands.To allow screw(➀) heads to pass through the rail holes. 3) Locate the eight phillips screws in the Fresh Select Zone. To lift the door up, unscrew the eight phillips screws(➀) four turns. Do not remove the screws (➀) out. (You don’t need to unscrew the adjuster-phillips screw(➁) 1) Open the Fresh Select Zone Door. 2) Take out the box in the Fresh Select Zone. 5) Slide the rail carefully to the inside. When you assemble the Fresh Select Zone Door, follow the contrary order.NOTE %& .
30 Reattaching the Freezer Door REATTACHING THE REFRIGERATOR DOORS 1) Reattach a phillips screw ( ➀) and two hex head screws (➁) to the hinge completely.2) Place the hole in the bottom of the door (➃) over the hinge ( ➂). 3) Insert the upper hinge shaft (➄) into the hole (➅). After levelling between the hinge brackets (➆). Reattach and close the latch ( ➇) along the arrow. Connect the water tube (➈) and the wires ( ➉). Then, place the water tube(➈) on the hanger ( ) 4) Put the connector ( ) in the guide ( ) of the connector-cover and close it.5) Put the front part of the upper hinge cover ( ) on the front part of the upper hinge ( ) and reattach it from the front of the upper hinge cover first. 6) Reattach a phillips screw to the hinge cover ( ). Be sure to insert the water tube and push to the end.NOTE 14 15 16 1213 11 %& .