Samsung ML 2955ND User Manual

							Wireless network setup512. Using a network-connected machine
14 The wireless network connects according to the network 
configuration.
15 When the wireless network setting is completed, disconnect 
the USB cable between the computer and machine. 
16 Follow the instructions on the screen to complete the 
installation. After the installation is finished, click Quit or 
Restart.

18 
Using a network cable
Your machine is a network compatible machine. To enable your 
machine to work with your network, you will need to perform some 
configuration procedures.
 
• After completing the wireless network connection, you 
need to install a machine driver to print from an 
application (See "Installing driver over the network" on 
page 17).
• See your network administrator, or the person that set up 
your wireless network, for information about your 
network configuration.
 
Items to prepare
•Access point
• Network-connected computer
• Software CD that was provided with your machine
• The machine installed with a wireless network interface
•Network cable
Printing a network configuration report
You can identify the network settings of your machine by printing a 
network configuration report.
See "Printing a network configuration report" on page 13.
IP setting using SetIP Program (Windows)
This program is used to manually set the network IP address of your 
machine using its MAC address to communicate with the machine. 
The MAC address is the hardware serial number of the network 
interface and can be found in the Network Configuration Report. 
See "Setting IP address" on page 13.
Downloaded From ManualsPrinter.com Manuals 
						

							Wireless network setup522. Using a network-connected machine
Configuring the machine’s wireless network
Before starting you will need to know the network name (SSID) of 
your wireless network and the network key if it is encrypted. This 
information was set when the access point (or wireless router) was 
installed. If you do not know about your wireless environment, 
please ask the person who set up your network.
To configure wireless parameters, you can use SyncThru™ Web 
Service.
Using SyncThru™ Web Service
Before starting wireless parameter configuration, check the cable 
connection status. 
1Check whether or not the network cable is connected to the 
machine. If not, connect the machine with a standard network 
cable.
2 Start a web browser such as Internet Explorer, Safari or Firefox 
and enter your machine’s new IP address in the browser 
window.
For example,
3 Click Login on the upper right of the SyncThru™ Web Service 
website.
4 Type in the ID and Password then click Login.
•ID: admin 
•Password: sec00000 
5 When the SyncThru™ Web Service window opens, click 
Network Settings.
6 Click Wireless > Wizard.
 
Wizard will help you setup the wireless network 
configuration. However, if you want to set the wireless 
network directly, select Custom.
 
Downloaded From ManualsPrinter.com Manuals 
						

							Wireless network setup532. Using a network-connected machine
7 Select the one Network Name(SSID) in the list.
•SSID: SSID (Service Set Identifier) is a name that identifies a 
wireless network, access points, and wireless devices 
attempting to connect to a specific wireless network must 
use the same SSID. The SSID is case-sensitive.
•Operation Mode: Operation Mode refers to the type of 
wireless connections (See "Wireless network name and 
network key" on page 30).
-Ad-hoc: Allows wireless devices to communicate 
directly with each other in a peer-to-peer environment.
-Infrastructure: Allows wireless devices to 
communicate with each other through an access point.
 
If your network’s Operation Mode is Infrastructure, select 
the SSID of the access point. If the Operation Mode is Ad-
hoc, select the machine’s SSID. Note that “portthru” is the 
default SSID of your machine.
 
8 Click Next.
If the wireless security setting window appears, enter the 
registered password (network key) and click Next.
9 The confirmation window appears, please check your wireless 
setup. If the setup is right, click Apply.
 
Disconnect the network cable (standard or network). Your 
machine should then start communicating wirelessly with 
the network. In case of Ad-hoc mode, you can use a wireless 
LAN and wired LAN simultaneously.
 

19 
Turning the Wi-Fi network on/off
 
You can also turn on/off the Wi-Fi from the machine’s control 
panel using the Network menu.
 
1Check whether the network cable is connected to the 
machine. If not, connect the machine with a standard network 
cable.
2 Start a web browser such as Internet Explorer, Safari or Firefox 
and enter your machine’s new IP address in the browser 
window.
For example,
Downloaded From ManualsPrinter.com Manuals 
						

							Wireless network setup542. Using a network-connected machine
3 Click Login on the upper right of the SyncThru™ Web Service 
website.
4 Type in the ID and Password then click Login.
•ID: admin 
•Password: sec00000 
5 When the SyncThru™ Web Service window opens, click 
Network Settings.
6 Click Wireless > Custom.
You can also turn the Wi-Fi network on/off.

20 
Troubleshooting
Problems during setup or driver installation
►Printers Not Found
• Your machine may not be turned on. Turn on your computer and 
the machine.
• USB cable is not connected between your computer and 
machine. Connect machine to your computer using the USB 
cable.• The machine does not support a wireless network. Check the 
machine's user's guide included on the software CD supplied 
with your machine and prepare a wireless network machine.
►Connecting Failure - Not Found SSID
• The machine is unable to search the network name (SSID) you 
have selected or entered. Check the network name (SSID) on your 
access point and try connecting again. 
• Your access point is not turned on. Turn on your access point.
Downloaded From ManualsPrinter.com Manuals 
						

							Wireless network setup552. Using a network-connected machine
►Connecting Failure - Invalid Security
• You configured security incorrectly. Check the configured 
security on your access point and machine.
►Connecting Failure - General Connection Error
• Your computer is not receiving a signal from your machine. 
Check the USB cable and your machine’s power.
►Connecting Failure - Connected Wired Network
• Your machine is connected with a wired network cable. Remove 
the wired network cable from your machine.
►PC Connection Error
• The configured network address is unable to connect between 
your computer and machine.
- For a DHCP network environment
The receives the IP address automatically (DHCP) when 
computer is configured to DHCP.
- For a Static network environment
The machine uses the static address when the computer is 
configured to static address.
For example:
If the computer’s network information is as shown below:
▪IP address: 169.254.133.42▪Subnet Mask: 255.255.0.0
Then, the machine’s network information should be as below:
▪IP address: 169.254.133.43
▪Subnet Mask: 255.255.0.0 (Use the computer’s subnet 
mask.)
▪Gateway: 169.254.133.1
Other problems
If problems occur while using the machine on a network, check the 
following: 
 
For information on the access point (or wireless router), refer 
to its own user's guide. 
 
•Your computer, access point (or wireless router), or machine may 
not be turned on.
• Check the wireless reception around the machine. If the router is 
far from the machine or there is an obstacle, you might have 
difficulty receiving the signal. 
• Cycle the power for the access point (or wireless router), machine, 
and computer. Sometimes cycling the power can recover 
network communication.
Downloaded From ManualsPrinter.com Manuals 
						

							Wireless network setup562. Using a network-connected machine
• Check whether firewall software (V3 or Norton) is blocking the 
communication. 
If the computer and the machine are connected on the same 
network and it cannot be found when searching, firewall 
software might be blocking the communication. Refer to the 
user's guide for the software to turn it off and try searching for the 
machine again.
• Check whether the machine's IP address is allocated correctly. 
You can check the IP address by printing the network 
configuration report.
• Check whether the access point (or wireless router) has a 
configured security (password). If it has a password, refer to the 
access point (or wireless router) administrator.
• Check the machine's IP address. Reinstall the machine driver and 
change the settings to connect to the machine on the network. 
Due to the characteristics of DHCP, the allocated IP address could 
change if the machine is not used for a long time or if the access 
point has been reset.
• Check the wireless environment. You might not be able to 
connect to the network in the infrastructure environment where 
you need to type in a user's information before connecting to 
access point (or wireless router).
• This machine only supports IEEE 802.11 b/g/n and Wi-Fi. Other 
wireless communication types (e.g., Bluetooth) are not 
supported.• When using the ad hoc mode, in operating systems such as 
Windows Vista, you might need to set the wireless connection 
setting every time you use the wireless machine. 
• You cannot use Infrastructure mode and Ad hoc mode at the 
same time for Samsung wireless network machines.
• The machine is within the range of the wireless network.
• The machine is located away from obstacles that could block the 
wireless signal.
Remove any large metal objects between the access point (or 
wireless router) and the machine.
Make sure the machine and wireless access point (or wireless 
router) are not separated by poles, walls, or support columns 
containing metal or concrete.
• The machine is located away from other electronic devices that 
may interfere with the wireless signal.
Many devices can interfere with the wireless signal, including a 
microwave oven and some Bluetooth devices.
Downloaded From ManualsPrinter.com Manuals 
						

							3. Useful management tools
This chapter introduces management tools provided to help you make full use 
of your machine. 
• Samsung AnyWeb Print 58
• Easy Eco Driver 59
• Using SyncThru™ Web Service 61
• Using Samsung Easy Printer Manager 65 
• Using Samsung Printer Status 68
• Using Smart Panel 70
• Using the Linux Unified Driver Configurator 72
† If you have Internet access, you can get help, support, machine drivers, 
manuals, and order information from the Samsung website, 
www.samsung.com/printer > find your product >download center.
Downloaded From ManualsPrinter.com Manuals 
						

							583. Useful management toolsSamsung AnyWeb Print
 
Available for Windows and Macintosh OS users only.
 
This tool helps you screen-capture, preview, scrap, and print pages 
more easily, than when you use an ordinary program.
To open the Program: 
•For Windows: Select Start > All Programs > Samsung Printers 
> Samsung AnyWeb Print > Download the latest version.
•For Macintosh: Open the Applications folder > Samsung folder 
> Samsung AnyWeb Print.
Downloaded From ManualsPrinter.com Manuals 
						

							593. Useful management toolsEasy Eco Driver
With the Easy Eco Driver, you can apply Eco features to save paper 
and toner before printing. To use this application, Start Easy Eco 
Driver before printing job checkbox in the printer properties 
should be checked. 
Easy Eco Driver also allows you simple editing such as removing 
images and texts, changing fonts, and more. You can save frequently 
used settings as a preset.
 
Available for Windows OS users only.
 
How to use: 
1 Open a document to print.
2 Print the document.
A preview window appears.
3 Select the options you want to apply to the document.
You can see the preview of the applied features.
4 Click Print.
Downloaded From ManualsPrinter.com Manuals 
						

							603. Useful management toolsUnderstanding Easy Capture Manager
Capture your screen and launch Easy Capture Manager by simply 
pressing the Print Screen key on the keyboard. Now you can easily 
print your captured screen as captured or edited. 
Downloaded From ManualsPrinter.com Manuals