Samsung LN-R269D TFT-LCD Television User Manual

Englis\b-65
CH\fNNELCONTROL
Edi\bing \bhe Channe\f Lis\bs
You can edit c\bannels to be added or deleted.
1
Press \bhe MENUbu\b\b\fn
\b\f display \bhe menu.
Press \bhe 
UP/DOWNbu\b\b\fns \b\f selec\b “Channel”,
\bhen press \bhe ENTERbu\b\b\fn.
2
Press \bhe UP/DOWNbu\b\b\fns \b\f selec\b “Channel
Lis\b”, \bhen press \bhe
ENTERbu\b\b\fn.
Press \bhe UP/DOWNbu\b\b\fns \b\f selec\b “Edi\b”, \bhen
press \bhe ENTERbu\b\b\fn.
3
Press \bhe UP/DOWNbu\b\b\fns \b\f selec\b “Channel”
and ENTERbu\b\b\fn.
Then, \bhe...

\fnglish\b66
CHANN\fLCONTROL
Fi\fe Tu\fi\fg A\falog Cha\f\fels
Use fine tuning to manually adjust a particular channel for optimal reception.
1
Press the MENUbutton
to displ\by the menu.
Press the 
UP/DOWNbuttons to sele\ft “Ch\bnnel”,
then press the ENTERbutton.
2
Press the UP/DOWNbuttons to sele\ft “Fine
Tune”, then press the
ENTERbutton.
3
Press the LEFT/RIGHTbuttons to \bdjust the fine 
tuning.
4
To store the fine tuning 
setting in the TV’s memory,
press the 
ENTER
button.
To reset the fine tuning...

\fnglish\b67
CHANN\fLCONTROL
Checki\fg the Digital-Sig\fal St\be\fgth
Unlike analog channels, which can vary in reception quality from “snowy” to clear,
digital (HDTV) channels have either perfect reception quality or you will not receive
them at all. So, unlike analog channels, you cannot fine tune a digital channel.
You can, however, adjust your antenna to improve the reception of available digital
channels.
1
Press the MENUbutton
to displ\by the menu.
Press the 
UP/DOWNbuttons to sele\ft “Ch\bnnel”,...

\fnglish\b68
CHANN\fLCONTROL
LNA (Low Noise Amplifie\b)
If the TV is operating in a weak\bsignal area, sometimes the LNA function can improve
the reception (a low\bnoise preamplifier boosts the incoming signal).
1
Press the MENUbutton
to displ\by the menu.
Press the 
UP/DOWNbuttons to sele\ft “Ch\bnnel”,
then press the ENTER
button.
2
Press the UP/DOWNbuttons to sele\ft “LNA”,
then press the ENTERbutton.
Press the 
UP/DOWNbuttons to sele\ft “On”, then
press the ENTERbutton.
Press the 
EXITbutton 
to...

\fnglish\b69
Chapte\b 7
PC DISPLAY
Usi\fg You\b TV as a Compute\b (PC) Display
Setti\fg Up You\b PC Softwa\be (Based o\f Wi\fdows XP)
The Windows display\bsettings for a typical computer are shown below. The actual screens on your PC
will probably be different, depending upon your particular version of Windows and your particular video
card. However, even if your actual screens look different, the same basic set\bup information will apply in
almost all cases. (If not, contact your computer manufacturer...

\fnglish\b70
How to Auto Adjust
Use the Auto Adjust function to have the TV set automatically adjust the video signals
the monitor receives. The function also automatically fine\btunes the settings and adjusts
the frequency values and positions.  
Note: This function does not work in DVI\bDigital mode.
1-1
Press the MENUbutton
to displ\by the menu.
Press the 
UP/DOWNbuttons to sele\ft “Setup”,
then press the ENTERbutton.
Press the 
UP/DOWNbuttons to sele\ft “PC”, then
press the ENTERbutton.
2
Press the...

\fnglish\b71
PC DISPLAY
Adjusti\fg the Sc\bee\f Quality
The purpose of the picture quality adjustment is to remove or reduce picture noise.
If the noise is not removed by fine tuning alone, then do the frequency adjustments to
the utmost and fine tune again. After the noise has been reduced, re\badjust the picture
so that it is aligned on the center of screen.
2
Press the ENTERbutton to sele\ft
“Im\bge Lo\fk”.
1-1
Press the MENUbutton
to displ\by the menu.
Press the 
UP/DOWNbuttons to sele\ft “Setup”,...

\fnglish\b72
3
Press the UP/DOWNbuttons to sele\ft
“Co\brse” or “Fine”,
then press the
ENTERbutton.
Press the
LEFT/RIGHTbuttons to \bdjust the
s\freen qu\blity. Verti\f\bl
stripes m\by \bppe\br or  
the pi\fture m\by be blurry.
Press the ENTERbutton.
Press the EXITbutton to
exit.


01 BN68-00910A-03Eng.qxd  10/20/05 3:33 PM  Page 72 

\fnglish\b73
PC DISPLAY
Cha\fgi\fg the Sc\bee\f Positio\f
2
Press the UP/DOWNbuttons to sele\ft
“Position”, then press
the 
ENTERbutton.
1-1
Press the MENUbutton
to displ\by the menu.
Press the 
UP/DOWNbuttons to sele\ft “Setup”,
then press the ENTER
button.
Press the 
UP/DOWNbuttons to sele\ft “PC”, then
press the ENTERbutton.
1-2
Press the MENUbutton
to displ\by the menu.
Press the 
UP/DOWNbuttons to sele\ft “Setup”,
then press the ENTERbutton.
Press the 
UP/DOWNbuttons to sele\ft “PC”, then
press the...

\fnglish\b74
3
Press the UP/DOWNbuttons to \bdjust the 
V-Position.
Press the
LEFT/RIGHTbuttons to \bdjust
the H-Position.
Press the ENTERbutton.
Press the EXITbutton 
to exit.
01 BN68-00910A-03Eng.qxd  10/20/05 3:34 PM  Page 74