Samsung LE 32A456 User Manual

							English - 9
Selecting the Time Zone (Spain only)
Select the local time zone.
1.  Press the MENU button to display the menu. 
Press the ▲ or ▼ button to select "Digital Menu", then press the 
ENTER
 button.
. Press the ▲ or ▼ button to select "Setup", then press the▲ or ▼ button to select "Setup", then press the button to select "Setup", then press the 
ENTER button.
. Press the ▲ or ▼ button to select "Time �one", then press the▲ or ▼ button to select "Time�one", then press the button to select "Time Zone", then press the 
ENTER button.
. Select the time zone where you locate by pressing the   ▲ or ▼ button.  
Press the ENTER button.
The following options are available   
The Iberian Peninsula and Balearic Islands  -   
Canary Islands
5. Press the EXIT button to exit.
➣
Viewing Product Information
You can view your product information. For service or repair, 
please contact a Samsung approved dealer.
1.   Press the MENU button to display the menu.  
Press the ▲ or ▼ button to select "Digital Menu", then press the 
ENTER
 button.
.  Press the ▲ or ▼ button to select "Setup", then press the    ENTER button.
. Press the ▲ or ▼ button to select "System", then press    the ENTER button.
. Press the ENTER button again, to select "Product    Information".
The Product Information menu is selected.  
- Software Version, Firmware Version
5. Press the EXIT button to exit.
➣
Setup

Audio Format  : PCM Audio Description Digital Text  : Enable Time Zone   Common Interfece
  
Move Enter Return
DTV
Time Zone
Adjust Enter Return
The Iberian Peninsula and balearic Islands  Canary Islands
DTV
Product InformationSoftware Version: T-PERLDEUC-0010Firmware Version: T-EMMA DEU b-0105
Return
DTV
BN68-01424D-Eng.indd   392008-03-03   ¿ÀÈÄ 5:22:06 
						

							English - 0
Upgrading the Software
To keep your product up-to-date with new Digital Television 
features then software upgrades are periodically broadcast as 
part of the normal Television signal.  
It will automatically detect these signals and display the 
software upgrade banner. You are given the option to install the 
upgrade.
1.   Press the MENU button to display the menu.  
Press the ▲ or ▼ button to select "Digital Menu", then press the 
ENTER
 button.
. Press the ▲ or ▼ button to select "Setup", then press the  ENTER button.
. Press the ▲ or ▼ button to select "System", then press the  ENTER button.
. Press the ▲ or ▼  button to select "Software Upgrade",  
then press the ENTER button.
5.   Press the ▲ or ▼ button to select “Software Information”,  
“Manual Upgrade” or “Standby Mode upgrade”.  
Press the ENTER
 button.♦    Software Information        Press the ENTER button, then the current software version is shown. To display the software version information, press the  ENTER button again. 
To switch to an alternative version, press the red button.  
Press the blue button to reset, activate the upgrade and restart.
♦
    Manual Upgrade     Press the ENTER button to search for new software from the currently broadcasting channels.
♦   Standby Mode Upgrade: On / Off       Press the ENTER button. To continue software upgrade with master power on, Select On by pressing the ▲ or ▼ button. 45 minutes after entering standby mode, a manual upgrade is 
automatically conducted. Since the power of the unit is turned on internally, the screen may be on 
slightly for the LCD product. This phenomenon may continue for more than 1 hour until the software 
upgrade is completed.
6. Press the EXIT button to exit.
Checking the Signal Information
You can get information about the signal status.
1.   Press the MENU button to display the menu.  
Press the ▲ or ▼ button to select "Digital Menu", then press the 
ENTER
 button.
.  Press the ▲ or ▼ button to select "Setup", then press the  ENTER button.
. Press the ▲ or ▼ button to select "System", then press the  ENTER button.
. Press the ▲ or ▼ button to select "Signal Information", then press the ENTER button.
5. Press the EXIT button to exit.
If the signal status is poor, the "No signal." message is displayed.➣
Move  Enter  Return
Signal InformationService: ?
Service ID:0000
Multiplex: ? (TSID 0000, ONID 0000)
Network: ? (ID 0000)
bit error level:       10Signal Strength:      0
Return
DTV
SystemProduct Information Signal Information  Software Upgrade Reset 
Move Enter Return
DTV
Software UpgradeSoftware Information  Manual Upgrade Standby Mode upgrade : On  
Move Enter Return
DTV
BN68-01424D-Eng.indd   402008-03-03   ¿ÀÈÄ 5:22:07 
						

							English - 1
Viewing Common Interface
This contains information on CAM inserted in the CI slot and 
displays it.
1.   Press the MENU button to display the menu. 
Press the ▲ or ▼ button to select "Digital Menu", then press the 
ENTER
 button.
. Press the ▲ or ▼ button to select "Setup", then press the  ENTER button.
. Press the ▲ or ▼  button to select "Common Interface", then 
press the ENTER button.
. Press the ENTER button to display the information for    your application.
5. Press the EXIT button to exit.
The Application Info inserting is about the CI CARD.  
You can install the CAM anytime whether the TV is ON or    OFF.
 1.    Purchase the CI CAM module by visiting your nearest dealer   or by phone. .  
Insert the CI CARD into the CAM in the direction of the     arrow until it fits. .  
Insert the CAM with the CI CARD installed into the common interface slot. 
(Insert the CAM in the direction of the arrow, right up to the 
end so that it is parallel with the slot.)
 . Check if you can see a picture on a scrambled signal channel.
➣
Selecting the CI (Common Interface) Menu
This enables the user to select from the CAM-provided menu.
1.   Press the MENU button to display the menu.  
Press the ▲ or ▼ button to select "Digital Menu", then press the 
ENTER
 button.
. Press the ▲ or ▼ button to select "Setup", then press the    ENTER button.
. Press the ▲ or ▼  button to select "Common Interface",  
then press the ENTER button.
. Select to "CI Menu" by pressing the  ▲ or ▼ button, and press the 
ENTER button.
5. Select the required option by pressing the  ▲ or ▼ button, and press the ENTER button.
6. Press the EXIT button to exit.
Select the CI Menu based on the menu PC Card.➣
CI MenuMain menu
Move Enter Exit
Module information
Smart card information
Language
Software Download
Press OK to select, or Exit to quit
Application InfoType : CA
Manufacturer : Channel Plus
Info : Top Up TV
Return
DTV
BN68-01424D-Eng.indd   412008-03-03   ¿ÀÈÄ 5:22:08 
						

							English - 
Selecting the Preferred Language (Subtitle, Audio or Teletext)
You can change the default value for subtitle, audio teletext 
languages. 
Displays the language information for the incoming stream.
1.   Press the MENU button to display the menu. 
Press the ▲ or ▼ button to select "Digital Menu", then press the 
ENTER
 button.
. Press the ▲ or ▼  button to select "Language", then press   
the ENTER button.
. Press the ▲ or ▼ button to select "Audio Language",  
"Subtitle Language" or "Teletext Language".   
Press the ENTER
 button.
. Select a particular language by pressing the  ▲ or ▼ button  repeatedly. 
Press the ENTER button.
English is the default in cases where the selected  language is unavailable in the broadcast.
5. Press the EXIT button to exit.
While viewing a programme, the subtitle can be selected  
While viewing a programme, audio languages can be  selected.
➣
➣
Resetting
You can reset the values stored to the factory default values.
The Reset operation deletes all channel information and  user preferences returning all values to their default factory  state.
1.   Press the MENU button to display the menu.  
Press the ▲ or ▼ button to select "Digital Menu", then press the 
ENTER
 button.
. Press the ▲ or ▼ button to select "Setup", then press the  ENTER button.
. Press the ▲ or ▼ button to select "System", then press  the ENTER button.
. Press the ▲ or ▼ button to select "Reset", then press the  ENTER button.
5. The "Enter PIN" screen will appear.
6. Enter your current 4-digit PIN code by using the numeric  buttons (0~9).
The warning message is displayed. All values will be reset 
by pressing the coloured buttons (red, green, yellow, and 
blue) in turn.
7. Press the EXIT button to exit.
➣
➣
Reset
Enter PIN
 Enter PIN Return
DTV
ResetWARNING: All channel settings and user
preferences will be lost and returned to the factory 
defaults. It is recommended that a reset is performed 
only when serious problems are experienced.
Return
DTV
Language
Audio Language 
Subtitle Language
Teletext Language
Preference       
Move Enter Return
DTV
Language
Audio Language 
Subtitle Language
Teletext Language
Preference       
Move Enter Return
DTV
Language
Audio Language 
Subtitle Language 
Teletext Language
Preference       
Move Enter Return
DTV
BN68-01424D-Eng.indd   422008-03-03   ¿ÀÈÄ 5:22:09 
						

							English - 
Preference
This menu consists of 6 sub-menus: 
Primary Audio Language, Secondary Audio Language, Primary 
Subtitle Language, Secondary Subtitle Language, Primary 
Teletext Language, Secondary Teletext Language.
Using this feature, users can select one of the languages 
(English, German, Italian, Swedish, French, Welsh, Gaelic, Irish, 
Danish, Finnish, Spanish, Dutch). The language selected here is the 
default when the user selects a channel.
♦     Press the ▲ or ▼ button to select required menu (Primary Audio Language, Secondary Audio Language, Primary Subtitle Language, Secondary Subtitle 
Language, Primary Teletext Language, Secondary Teletext Language), then press the  ENTER button. The options of the selected menu are displayed.
♦  	Select the appropriate language by pressing the ▲ or ▼ button.   
Press the  ENTER button to confirm your choice.
  If you change the language setting, the Subtitle Language, Audio Language, and the Teletext Language of the Language menu (refer to page  42) are automatically changed to the selected 
language.
The Subtitle Language, Audio Language, and the Teletext Language of the Language menu show a 
list of languages supported by the current channel and the selection is \
highlighted. If you change this 
language setting, the new selection is only valid for the current channe\
l. The changed setting does not 
change the setting of the Primary Subtitle Language, Primary Audio Language, or the Primary Teletext 
Language of the Preference menu.➣
➣
Move  Enter  Return
Language
Audio Language 
Subtitle Language
Teletext Language
Preference       
Move Enter Return
DTV
BN68-01424D-Eng.indd   432008-03-03   ¿ÀÈÄ 5:22:09 
						

							English - 
The Windows display-settings for a typical computer are shown below. The 
actual screens on your PC may be different depending upon your particular 
version of Windows and your particular video card. Even if your actual 
screens look different, the same, basic set-up information will apply in almost 
all cases. (If not, contact your computer manufacturer or Samsung Dealer.)
1.
 First, click on "Control Panel" on the Windows start menu.
. When the control panel window appears, click on "Appearance and Themes"    and a display dialog-box will appear.
.   When the control panel window appears, click on "Display" and a display  
dialog-box will appear.
.  Navigate to the "Settings" tab on the display dialog-box.    The correct size setting (resolution): Optimum- 1360 X 768  If a vertical-frequency option exists on your display settings dialog box, the correct value is   "60" or "60 Hz". Otherwise, just click "OK" and exit the dialog box. 
Setting up Your PC Software (based on Windows XP)
When using an HDMI/DVI cable connection, you must use the HDMI IN 2 jack\
.The interlace mode is not supported.
The set might operate abnormally if a non-standard video format is selec\
ted.
Separate and Composite modes are supported. SOG is not supported.  ➣
➣
➣
➣
Display Modes
both screen position and size will vary depending on the type of PC monitor and its resolution. 
The resolutions in the table are recommended. 
ModeResolutionhorizontal Frequency (khz)Vertical Frequency (hz)Pixel Clock Frequency (Mhz)Sync Polarity (h/V)
VESA 640×480
 
800×600  
1024×768  
1360 x 768
31.469 
37.879  
48.363  
47.712 59.940
 
60.317  
60.004  
60.015 25.175
 
40.000  
65.000  
85.500 -/- 
+/+  -/- 
+/+
 D-Sub Input
 hDMI/DVI Input 
ModeResolutionhorizontal Frequency (khz)Vertical Frequency (hz)Pixel Clock Frequency (Mhz)Sync Polarity (h/V)
IbM640x350  
720×400 31.469
 
31.469  70.086
 
70.087  25.175   
28.322 +/- 
-/+
VESA
640×480
 
640×480  
640×480  
800×600  
800×600  
800×600   
1024×768  
1024×768  
1024×768  
1360 x 768 31.469
 
37.861  
37.500  
37.879  
48.077  
46.875  
48.363  
56.476  
60.023  
47.712 59.940
 
72.809  
75.000  
60.317  
72.188  
75.000  
60.004  
70.069  
75.029  
60.015 25.175
 
31.500  
31.500  
40.000  
50.000  
49.500  
65.000  
75.000  
78.750  
85.500 -/- 
-/- 
-/- 
+/+ 
+/+ 
+/+  -/- 
-/- 
+/+ 
+/+
BN68-01424D-Eng.indd   442008-03-03   ¿ÀÈÄ 5:22:09 
						

							English - 5
Setting up the TV with your PC
  Preset: Press the  SOURCE button to select PC mode.
1.
    Press the MENU button to display the menu. 
Press the  ENTER button, to select "Picture".
.   Select the required option by pressing the ▲ or ▼ button, then press the  ENTER button.
.   When you are satisfied with your setting, press the  
ENTER button.
.   Press the  EXIT button to exit.  
 
♦
    Auto Adjustment        Auto adjustment allows the PC screen of set to self-adjust to the incoming PC video signal. The values of fine, coarse and 
position are adjusted automatically.
Easy Setting
1.  Press the  TOOLS button on the remote control.
.   Press the ▲ or ▼ button to select “Auto Adjustment”, then press the  ENTER button.
♦   Screen Adjustment:    Coarse/Fine       The purpose of picture quality adjustment is to remove or reduce picture noise. If the noise is not removed by Fine-
tuning alone, then adjust the frequency as best as possible 
(coarse) and Fine-tune again. After the noise has been 
reduced, re-adjust the picture so that it is aligned on the 
center of screen. 
Press the ▲ or ▼ button to select "Coarse" or "Fine", then 
press the  ENTER
 button. 
Press the ◄ or ► button to adjust the screen quality. 
Press the  ENTER
 button.
   
   Position       Adjust the PC’s screen positioning if it does not fit the TV screen. 
Press the ▲ or ▼ button to adjusting the Vertical-Position. 
Press the ◄ or ► button to adjust the Horizontal-Position.
Press the  ENTER
 button.
     Image Reset 
You can replace all image settings with the factory default 
values.
Screen AdjustmentCoarse     50Fine     Position    
Image Reset     
TV
 Move    Enter Return
Position
TV
 Move  
 Enter Return
PictureMode  : Standard   backlight       7Contrast      95brightness      5Sharpness      50 Auto Adjustment          Screen Adjustment                           Detailed Settings       Picture Options       Reset : OK   
TV
 Move   Enter Return
Screen AdjustmentCoarse     50Fine     Position    
Image Reset     
TV
 Move    Enter Return
Auto Adjustment in progress
Please wait.
Anynet+ (hDMI-CEC)Picture Mode  : StandardSound Mode : CustomSleep Timer : OffSRS TS XT : OffEnergy Saving : OffAuto Adjustment
 Move   Enter Exit
Tools
BN68-01424D-Eng.indd   452008-03-03   ¿ÀÈÄ 5:22:11 
						

							English - 6
Connecting Anynet+
 Devices
The Anynet+ system supports AV devices supporting Anynet+ only.
Check if there is an Anynet+ mark on the AV device to be connected to the TV.
To directly connect to TV
Connect the [HDMI 1], [HDMI 
2] or [HDMI 3] jack on the TV 
and the HDMI OUT jack of the 
corresponding Anynet+ device 
using the HDMI cable.
To connect to home Theater
1. Connect the [HDMI 1], [HDMI 2] or [HDMI 3] 
jack on the TV and the 
HDMI OUT jack of the 
corresponding Anynet+ 
device using the HDMI 
cable.
. Connect the HDMI IN jack of the home theatre and 
the HDMI OUT jack of the 
corresponding Anynet+ 
device using the HDMI 
cable.
 
Connect only the optical cable between [Digital Audio Out (Optical)] on your TV and Digital Audio 
Input on the receiver.
Connect only one receiver.
You can listen to 5.1 channel sound through the home theatre’s speakers. Otherwise, you can only 
listen to 2 channel stereo sound in other cases. Make sure to connect th\
e Digital Audio IN (Optical) of 
the home theatre and the TV correctly to listen to TV sound through the home theatre. However, you 
cannot listen to sound from the BD recorder that is sent to the home the\
atre via the TV in 5.1 channel 
sound because the TV outputs only 2 channel stereo sound. Please see the manual for the home 
theatre.
You can connect an Anynet+ device using the  HDMI cable. Some HDMI cables may not support 
Anynet+ functions.
Anynet+ works when the AV device supporting Anynet+ is in the Standby or On status.
Anynet+ supports up to 8 AV devices in total.
➣
➣
➣
➣
➣
➣
What is Anynet +
? 
Anynet+ is an AV network system that enables an easy-to-use AV interface for users by controlling 
all connected AV devices through the Anynet+ menu when Samsung Electronics AV devices are 
connected.
Anynet+ Device 1Anynet+ Device Anynet+ Device TV
hDMI CablehDMI CablehDMI Cable
TV
Anynet+ Device 1
Anynet+ Device 
Anynet+ Device 
hDMI CablehDMI Cable
hDMI Cable
hDMI Cable
home Theatre
Optical Cable
BN68-01424D-Eng.indd   462008-03-03   ¿ÀÈÄ 5:22:11 
						

							English - 7
Setting Up Anynet+
The following settings are to use Anynet+ functions.
Using the Anynet+ Function
1.
 
Press The TOOLS  button. Then Press the ENTER button 
to select "Anynet+(HDMI-CEC)". 
Press the ▲ or ▼ button to select  "Setup", then press the 
ENTER
 button..  Press the ENTER button to select "Anynet+ (HDMI-CEC)", 
then press the ENTER button..  Press the ▲ or ▼ button to select "On", then press the  
ENTER button.
The "Anynet+ (HDMI-CEC)" function is enabled.
If you select "Off", "Anynet+ (HDMI-CEC)" is disabled.
When the "Anynet+ (HDMI-CEC)"  function is disabled, all the 
Anynet+ related operations are deactivated.
Turning an Anynet+ Device Off Automatically when the TV is Turned Off
1.
  Press the ▲ or ▼ button to select  "Auto Turn Off", then press 
the ENTER button..  Press the ▲ or ▼ button to select "Yes", then press the  
ENTER button.
The Auto turn off function is enabled.
If you select "No", the Auto turn off function is cancelled .
 Press the EXIT button to exit.
The Select Device setting of the TV remote control is to be set 
to TV to use the Anynet+ function.
If you set "Auto Turn Off" to " No", connected external devices 
are also turned off when the TV is turned off. However, if the 
device is recording, it may not be turned off.
➣
➣
➣
➣
➣
➣
➣
Setup
Anynet+ (hDMI-CEC)  : Off
Auto Turn Off   : Off
Searching Connections 
Off
On
Move    Enter Return
Setup
Anynet+ (hDMI-CEC) : On
Auto Turn Off   : Off
Searching Connections 
No
Yes
Move    Enter Return
View TV Select Device Record   Menu on Device Device Operation Receiver :Off Setup   
TVP9
Move    EnterReturn
Anynet+ (hDMI-CEC)Picture Mode  : StandardSound Mode : CustomSleep Timer : OffSRS TS XT : OffEnergy Saving : OffDual l-ll : Mono
 Move   Enter Exit
Tools
BN68-01424D-Eng.indd   472008-03-03   ¿ÀÈÄ 5:22:12 
						

							English - 
Scanning and Switching between Anynet+
 Devices
1.   Press the TOOLS  button. Then press the ENTER button to select "Anynet+(HDMI-CEC)"..  Press the ▲ or ▼ button to select "Select Device", then press the ENTER button..   Press the ▲ or ▼ button to select to a particular device and press the ENTER button. It is switched to the selected device..  If you cannot find a device you want, press the ▲ or ▼ button to select "Setup", then press the ENTER button.5.  Press the ▲ or ▼ button to select "Searching Connections", then press the ENTER button.   The message "Configuring Anynet+ connection..." is displayed. 
When searching devices completes, the connected devices are 
listed in the Anynet+ menu.
Switching to the selected devices may take up to 2 minutes.   
You cannot cancel the operation during the switching operation.
The time required to scan for devices is determined by the 
number of connected devices.
When the device scan is complete, the number of found 
devices is not displayed.
Although the TV automatically scans devices when it is turned on using the  POWER button, devices 
connected when the TV is on or under a specific circumstance are not displayed in the device list. 
Therefore select "Searching Connections"  menu to search devices.
If you have selected external input mode by pressing the  SOURCE button, you cannot use the 
Anynet+ function. Make sure to switch to an Anynet+ device by using the  TOOLS button.
➣
➣
➣
➣
➣
Move    Enter Return
Setup
Anynet+ (hDMI-CEC) :   On 
Auto Turn Off   : Yes 
Searching Connections       
Move   Enter Return
View TV Select Device Record   Menu on Device Device Operation Receiver :Off Setup   
TVP9
Move    EnterReturn
BN68-01424D-Eng.indd   482008-03-03   ¿ÀÈÄ 5:22:13