Samsung LCD TV Ltn406w User Manual

English-14
INSTALLATION
Connecting the Speakers
5.1. Channel system: 5 channels – 2 channels for the front (left and right);                       
1 channel for the center; and 2 for the rear (left and right)
0.1 Channel – Subwoofer Channel
 The center, rear (left and right) and the subwoofer speakers are sold separately.
 Contact the nearest electronics store to purchase them.
1. Connect the speaker cables to the Speaker OUT jacks on the TV and the IN jacks on the speakers.
2. Connect the Subwoofer...

English-15
INSTALLATION
Connecting a PC
Note: This figure shows the Standard Connector-jack panel. The actual configuration on
your TV may be different, depending on the model.
PC VIDEO CABLE
( DVI-D+DVI-D )
PC AUDIO  CABLE
 PC AUDIO INPUT
Connect these to the audio-output jacks on your PC.
 PC VIDEO INPUT
Connect to the video output port on your PC.
# Each external input source device has a different back panel configuration.
TV rear panel PC rear
PC VIDEO CABLE
( DVI + D-SUB)
PC AUDIO  CABLE
TV rear...

English-16
Changing Channels
Using the Channel Buttons
1
Press the CH/ buttons to change channels.
When you press the CH/buttons, the TV changes channels in sequence.
You will see all the channels that the TV has memorized. (The TV must have 
memorized at least three channels.) You will not see channels that were either erased
or not memorized.
Using the Pre-CH Button to select the Previous Channel
1
Press the PRE-CHbutton.
The TV will switch to the last channel viewed.
To quickly switch between two...

English-17
SPECIALFEATURES
1
Press MUTEand the sound cuts off. 
The word “ ” will appear in the lower-left corner of the screen.
2
To turn mute off, press the MUTEbutton again, or simply
press either the VOL +/–button.
Using Mute
At any time, you can temporarily cut off the sound using the Mute button.
Viewing the Display
The display identifies the current channel and the status
of certain audio-video settings. 
The on-screen displays
disappear after about ten seconds.
Press the button once more or wait...

English-18
Setting Up Your Remote Control
After it has been set up properly, your remote control can operate in four different modes:
TV, VCR, Cable, or DVD. Pressing the corresponding button on the remote cont\
rol allows
you to switch between these modes, and control whichever piece of equipm\
ent you hoose.
Note
The remote control might not be compatible with all DVD Players, VCRs and Cable boxes.
Note on Using Remote Control Modes: VCR
When your remote control is in “VCR” mode, the volume buttons...

English-19
Setting Up the Remote to Operate Your Cable Box
Note on Using Remote Control Modes: Cable Box
When your remote control is in “Cable Box” mode, the volume button\
s still control your TV’s volume.
1Turn off your cable box.
2Press the MODE button and make sure that the Cable LED is illuminated.
3Press the SET button on your TV’s remote control.
4Using the number buttons on your remote control, enter three digits of the cable box code listed on page 21 of this manual
for your brand of cable box....

English-20
Setting Up the Remote to Operate Your DVD
Note on Using Remote Control Modes: DVD
When your remote control is in “DVD” mode, the volume buttons stil\
l control your TV’s volume.
1Turn off your DVD.
2Press the MODE button and make sure that the DVD LED is 
illuminated.
3Press the SET button on your TV’s remote control.
4Using the number buttons on your remote control, enter three  digits of the DVD code listed on page 21 of this manual for 
your brand of DVD. Make sure you enter three digits of...

English-21
Remote Control Codes
Admiral
Aiwa
Audio Dynamics
Bell&Howell
Broksonic
Candle
Canon
Citizen
Colortyme
Craig
Curtis-Mathes
Daewoo
DBX
Dimensia
Dynatech
Electrohome
Emerson
Fisher
Funai
GE
Go Video
Harman Kardon
Hitach
Instant Replay
JC Penney
JCL
JVC
kenwood015,088
024
022,025
011
019
016,018,022,054,055,061
017,062
016,018,022,054,055,061
023
016,021
009,016,017,023,024,055,062,073,076
003,004,005,006,007,008,022,054,085
009
024
036
017,018,019,022,024,029,032,036,043,...

English-22
Chapter Four
OPERATION
Plug & Play Feature
When the TV is initially powered On, two basic customer settings proceed
automatically and subsequently: Setting Auto program, Clock.
1
Press the POWER
button on the remote
control.
The message “Plug &
Play” is displayed.
2
Press the ENTER
button. 
The TV will begin  mem-
orizing all of the avail-
able channels.
3
Press the LEFT/RIGHT
buttons to move
to the hour or minute.
Set the hour or minute
by pressing the
UP/DOWNbuttons.
(refer to “Setting and...

English-23
OPERATION
Memorizing the Channels
Your TV can memorize and store all of the available channels for both “off-air” (antenna)
and cable channels. After the available channels are memorized, use the CH and CH
buttons to scan through the channels. This eliminates the need to change channels by
entering the channel digits. There are three steps for memorizing channels: selecting a
broadcast source, memorizing the channels (automatic) and adding and deleting channels
(manual).
Selecting the Video...