Samsung LCD TV Lt-P468w User Manual

							69
Setting the PictureChanging the Screen SizePress the [P.SIZE] button to change the screen size.Each press of the [P.SIZE] button switches the picture
size between , , ,
 and .
Wide
Panorama
Zoom1   Position
4:3
Note
• Zoom mode is only
enabled when the input
source is TV, AV, S-Video
or Component.
• Panorama, Zoom 1 or
Zoom 2 is disabled in PC
or DVI mode.
• The screen size can be
adjusted in each input
mode, and the PIP is only
enabled in Wide mode.
• The Panorama mode is
disabled in Component
modes (480p, 720p,
1080i, 1080p).
Caution
Displaying stationary
images that exceed the
above guidelines can cause
uneven aging of the display
that leave subtle, but
permanent burned-in ghost
images in the picture.
To avoid this, vary the
programming and images,
and primarily display full
screen moving images, not
stationary patterns or dark
bars that may appear when
you select the 4:3(Normal)
picture mode. Be careful in
the selection and duration of
television formats used for
viewing. Uneven display
aging as a result of format
selection and use, as well
as burned-in images, are
not covered by your
Samsung limited warranty.Picture Size
Wide
Sets the picture to 16:9 Wide Mode suitable
for DVD or Wide pictures.
PanoramaUse this mode to change from 16:9 to 4:3
mode.
Zoom1Magnifies the 16:9 mode to fill the full screen.
Press the […/†]button to move the picture up
or down.
Zoom2Magnifies the size of the screen in Zoom1
mode.
Press the 
[…/†]button to move the picture up
or down.
4:3Sets the video or current picture to 4:3
standard mode.
…
†
Zoom2   Position…
†
BN68-00665D-01_52~73  9/1/04  3:03 AM  Page 69  
						

							Picture… MoreBrightness Sensor: On√
Size : Wide√
Film Mode : Off√
Digital NR : On√
Move Enter Return
Picture… MoreBrightness Sensor: On
Size : Wide
Film Mode: Off
Digital NR : On
Move Enter Return
Film Mode Setup
70
Setting the Picture
Film Mode Setup
Use Film Mode for the best picture quality when viewing a film.
1Press the [MENU] button.The menu will be displayed.
2
Press the […/†] buttons to move to , then press
the [ENTER] button.
The  menu will be displayed.
3
Press the […/†] buttons to move to , then
press the [ENTER] button to display the 
selections.
4
Press the […/†] buttons to move to , then press the
[ENTER] button.
The  is set to .
Select  to deselect Film Mode.
5Press the [EXIT] button to finish.
Note
Film Mode is only
enabled in Video, S-
Video or Component
(480i) mode.
1
MENU
2,3,4
ENTER
2,3,4
…/†
5
EXIT
OffOn
BN68-00665D-01_52~73  9/1/04  3:03 AM  Page 70  
						

							Picture… MoreBrightness Sensor: On√
Size : Wide√
Film Mode : Off√
Digital NR : On√
Move Enter Return
Picture… MoreBrightness Sensor: On
Size : Wide
Film Mode : Off
Digital NR: On
Move Enter Return
OffOn
Digital Noise Reduction
71
Setting the PictureDigital Noise Reduction (NR)
If the broadcast signal received by your TV is weak, you can activate the Digital Noise Reduction feature to help
reduce any static and ghosting that may appear on the screen.
1Press the [MENU] button.The menu will be displayed.
2
Press the […/†] buttons to move to , then press
the [ENTER] button.
The  menu will be displayed.
3
Press the […/†] buttons to move to , then
press the [ENTER] button to display the 
selections.
4
Press the […/†] buttons to move to , then press the
[ENTER] button.
The  is set to .
Select  to deselect the Digital NR function.
5Press the [EXIT] button to finish.
1
MENU
2,3,4
ENTER
2,3,4
…/†
5
EXIT
BN68-00665D-01_52~73  9/1/04  3:03 AM  Page 71  
						

							SetupTime√
Plug & Play√
V-Chip√
Caption√
Language : English√
Blue Screen : Off√
Color Weakness: Off√
† More
Move Enter Return
SetupTime
Plug & Play
V-Chip
Caption
Language : English
Blue Screen: Off
Color Weakness: Off
† More
Move Enter Return
Blue Screen Mode Setup
72
Setting the Picture
Blue Screen Mode Setup
If no signal is being received or the signal is very weak, a blue screen automatically replaces the noisy picture.
To view channels with weak signals, it may be necessary to turn the Blue Screen mode Off.
1Press the [MENU] button.The menu will be displayed.
2
Press the […/†] buttons to move to , then press
the [ENTER] button.
The  menu will be displayed.
3
Press the […/†] buttons to move to , then
press the [ENTER] button to display the 
selections.
4
Press the […/†] buttons to select , then press the
[ENTER] button.
The  is set to .
Select  to deselect the Blue Screen function.
5Press the [EXIT] button to finish.
1
MENU
2,3,4
ENTER
2,3,4
…/†
5
EXIT
OffOn
BN68-00665D-01_52~73  9/1/04  3:03 AM  Page 72  
						

							Freezing the Picture
73
Setting the PictureFreezing the Picture
Press the [STILL] button.Each press of the [STILL] button toggles between On and Off.
Still
Note
Normal sound will still be heard when the picture
is frozen.
BN68-00665D-01_52~73  9/1/04  3:03 AM  Page 73  
						

							BN68-00665D-01_74~83  9/1/04  3:03 AM  Page 74  
						

							Setting the Sound
Selecting the Sound Mode .................................. 76
Adjusting the Equalizer ...................................... 77
Setting Multi-Channel Sound (MTS) ...................... 78
Automatic Volume Control .................................. 79
SRS TruSurround XT Setup .................................. 80
Setting the Sub Woofer Output............................ 81
Selecting the Sub(PIP) Window Sound ................. 82
Setting up the Melody Sound .............................. 83
BN68-00665D-01_74~83  9/1/04  3:03 AM  Page 75  
						

							SoundMode : Standard√
Equalizer√
MTS : Stereo√
Auto Volume : Off√
SRS TSXT : Off√
Sub Woofer√
Sound Select : Main√
Move Enter Return
SoundMode: Standard
Equalizer
MTS : Stereo
Auto Volume : Off
SRS TSXT : Off
Sub Woofer
Sound Select : Main
Move Enter ReturnStandardMusic
Movie
Speech
Custom
Selecting the Sound Mode
76
Setting the Sound
Selecting the Sound Mode
You can select a sound setting among ,  or .
1Press the [MENU] button.The menu will be displayed.
2
Press the […/†] buttons to move to , then press
the [ENTER] button.
The  menu will be displayed.
3Press the [ENTER] button to select .
4
Press the […/†] buttons to move to the desired sound
mode, then press the [ENTER] button.
Each time you press the […/†] button you cycle through
, , ,  and .
5Press the [EXIT] button to finish.
1
MENU
2,3,4
ENTER
2,3,4
…/†
5
EXIT
Sound Mode
StandardStandard settings suitable for all programs.MusicEnhances of playback of music.MovieEmphasizes bass tones.SpeechEmphasizes crisp, clear dialogue.CustomRecalls your personalized settings. √See page 77
BN68-00665D-01_74~83  9/1/04  3:03 AM  Page 76  
						

							SoundMode : Standard√
Equalizer√
MTS : Stereo√
Auto Volume : Off√
SRS TSXT : Off√
Sub Woofer√
Sound Select : Main√
Move Enter Return
Equalizer
Move Adjust Return
Adjusting the Equalizer
77
Setting the SoundAdjusting the Equalizer
You can adjust the L/R balance and different frequencies.
1Press the [MENU] button.The menu will be displayed.
2
Press the […/†] buttons to move to , then press
the [ENTER] button.
The  menu will be displayed.
3
Press the […/†] buttons to move to , then
press the [ENTER] button to display the 
adjustments.
4Press the [œ/√] buttons to move to the item of your
choice, then press the […/†] buttons to adjust.
5Press the [EXIT] button to finish.
1
MENU
2,3,4
ENTER
2,3,4
…/†
5
EXIT
100     300     1K     3K     10K
R
L
Sound Adjustment
Equalizer
Move Adjust Return
100     300     1K     3K     10K
R
L
Ϋ
1L/R Sound Balance Adjustment
To adjust the sound balance of the
L/R speakers.
2Bandwidth Adjustment
To adjust the level of different
bandwidth frequencies.
BN68-00665D-01_74~83  9/1/04  3:04 AM  Page 77  
						

							SoundMode : Standard√
Equalizer√
MTS : Stereo√
Auto Volume : Off√
SRS TSXT : Off√
Sub Woofer√
Sound Select : Main√
Move Enter Return
SoundMode : Standard
Equalizer
MTS: Stereo
Auto Volume : Off
SRS TSXT : Off
Sub Woofer
Sound Select : Main
Move Enter Return
MonoStereo
SAP
Setting Multi-Channel Sound (MTS)
78
Setting the Sound
Setting Multi-Channel Sound (MTS)
Depending on the particular program being broadcast, you can listen to stereo, mono, or a Secondary Audio
Program. (SAP audio is usually a foreign-language translation. Sometimes SAP has unrelated information like
news or weather.)
1Press the [MENU] button.The menu will be displayed.
2
Press the […/†] buttons to move to , then press
the [ENTER] button.
The  menu will be displayed.
3Press the […/†] buttons to move to , then press
the [ENTER] button to display the  selections.
4
Press the […/†] buttons to move to the desired MTS
Setting, then press the [ENTER] button.
Each time you press the […/†] button you cycle through “Mono”,
“Stereo” and “SAP”.
5Press the [EXIT] button to finish.
Press the [MTS] button.Each press of the [MTS] button cycles through ,
 and .
1
MENU
2,3,4
ENTER
2,3,4
…/†
5
EXIT
MTS : Stereo
Note
• The MTS function
operates in TV mode
only.
MTS Setting
StereoChoose Stereo for channels that are broadcasting in stereo.
MonoChoose Mono for channels that are broadcasting in mono, 
or if you are having difficulty receiving a stereo signal.
SAPChoose SAP to listen to the Secondary Audio Program, 
which is usually a foreign-language translation.
BN68-00665D-01_74~83  9/1/04  3:04 AM  Page 78