Samsung Ht D350k User Manual

							10 EnglishEnglish 11
02 Connections
This section involves various methods of connecting the product to other external components. 
Before moving or installing the product, be sure to turn off the power and disconnect the power cord.
Connecting the Speakers
Front Speakers ei
Place these speakers in front of your listening position, facing inwards (about 45°) 
toward you. Place the speakers so that their tweeters will be at the same height 
as your ear. Align the front face of the front speakers with the front face of the 
Center speaker or place them slightly in front of the Center speakers.
Center Speaker fIt is best to install it at the same height as the front speakers. You can also install it 
directly over or under the TV.
Surround Speakers
hj
Place these speakers to the side of your listening position. If there isn't enough 
room, place these speakers so they face each other. Place them about 60 to 
90cm above your ear, facing slightly downward.
*    Unlike the front and Center speakers, the surround speakers are used to 
handle mainly sound effects and sound will not come from them all the time.
Subwoofer 
gThe position of the subwoofer is not so critical. Place it anywhere you like.
Position of the product
Place it on a stand or cabinet shelf, or under the 
TV stand.
Selecting the Listening PositionThe listening position should be located about 2.5 
to 3 times the distance of the TV's screen size 
away from the TV. 
 Example :    For 32" TV's 2~2.4m   
For 
55" TV's 3.5~4m   
SW
CAUTION
Do not let children play with or near the speakers. They could get hurt if the speaker falls.
When connecting the speaker wires to the speakers, make sure that the polarity (+ /–) is correct.
   Keep the subwoofer out of the reach of children so as to prevent them from inserting their hands or alien 
substances into the duct (hole) of the subwoofer.
 

  Do not hang the subwoofer on the wall through the duct (hole).
NOTE
If you place a speaker near your TV set, screen Color may be distorted because of the magnetic field 
generated by the speaker. If this occurs, place the speaker away from your TV set.
!
`
`
`
`
✎
`
Connections
 
						

							1 English
Connections
English 1
Speaker Components
SPEAKERCABLEFRONT
(L)(R)SUBWOOFER
SURROUND
(L)(R)CENTER
Speaker ComponentsAssembled Speakers
HT-D350K
HT-D355K

FRONT
SURROUND
(L) (R)STAND
STANDBASE
(L) (R)
SCREW (5×15): 4EA
SCREW (4×20): 16EA
SUBWOOFER
Center SPEAKER
FRONT/SURROUND  SPEAKER
SUBWOOFER
CENTER
HT-D355K
SPEAKERCABLE
HT-D353HK

HT-D353HK
SPEAKER
CABLESURROUND
(L) (R)
Stand Nut: 2EA
STANDBASEFRONT
(L) (R)
SUBWOOFER
CENTER
SUBWOOFER
FRONT SPEAKER
SURROUND 
SPEAKER
Center SPEAKERStand Screwdriver: 2EA
 
						

							1 EnglishEnglish 1
02 Connections
Installing the Speakers on the Tallboy Stand
* HT-D355K only - Front/Surround SpeakersTurn the Stand Base upside-down and connect it to 
the Stand.
Insert small screws (4*20, For connecting Stand & Stand 
Base) clockwise into the four holes marked using a 
screwdriver as shown in the illustration. 
 CAUTION : When you use a torque screwdriver, be 
careful not to put excessive force. Otherwise, it runs 
idle or can be damaged. (torque screwdriver- below 15 
kg.f.cm)
1.
2.
!
12
Stand
Stand 
Base
Connect the upper Speaker to the assembled Stand.
Insert another large screw (5*15, For connecting Speaker 
& Stand)
  clockwise into the hole on the rear of the 
speaker using a 
screwdriver.
This is the appearance after the speaker is installed. 
Follow this steps to install other speaker.
3.
4.
5.
5
4
5
43
Stand
Speaker
Installing the Speakers on the Half Tallboy Stand
* HT-D353HK only - Front Speakers
Stretch out the speaker cable and arrange it through 
the hole of the stand base as shown.
Tighten the stand nut (C) as shown and use the stand 
screwdriver (D) to tighten it in the arrow direction.
This is after the speaker is installed completely.
Tighten the other speakers in the same manner.
1.
2.
3.
Adjusting the height of the Half Tallboy Speaker
* HT-D353HK only - Front SpeakersIf you want to change the speaker position (height), 
remove two screws in the rear side.
Pull up the speaker in the arrow direction as shown. 
(See fi gure 2)
CAUTION : Do not apply excessive force. Otherwise, it 
may cause a physical injury.
1.
2.
!
1
1
2
1
Connections
2
Installing the Speakers on the Tallboy Stand
3
 
						

							1 English
Connections
English 1
Connecting The Speakers
Press down the terminal tab on the back of the speaker. 
Insert the black wire into the black terminal (–) and the red wire into the red 
terminal (+), and then release the tab.
Connect the connecting plugs to the back of the product by matching the 
Colors of the speaker plugs to the speaker jacks.
1.
2.
3.
BlackRed
Connecting the wall mount
Connect the speaker cord with the color tube 
to (+), and the speaker cord without the color 
tube to (–).
Prepare screws (not supplied) that are suitable 
for the hole on the back of each speaker.
See the illustrations below.
Fasten the screws to the wall, then hang the 
speaker on the wall.
1.
2.
3.Color tube
Front left speaker (L) : White
Front right speaker (R) : Red
Center speaker : Green
Surround left speaker (L) : Blue
Surround right speaker (R) : Gray
5 mm
10 mm
Hold on the back of the  speaker
30 mm 4 mm
8 to 10 mm
Depth of fastened screw
Adjust the speaker height by fi tting it up to any of the 
provided holes. See the following examples for the speaker 
height.
Hole 1: 650mm for the speaker height.
Hole 2: 635mm for the speaker height.
(The default speaker height is 570mm)
Close the cover and tighten two screws as shown.
This is after the speaker height is adjusted. 
Follow the steps above to adjust the speaker height 
at any time.
3.
4.
5.34
5
Hole 1Hole 2
 
						

							1 EnglishEnglish 1
02 Connections
Connecting the video Out to your Tv
Choose one of the three methods for connecting to a TV.
METHOD 1 : HDMI
Connect an HDMI cable (supplied) from the HDMI OUT jack on the back of the product to the HDMI IN jack 
on your TV.
METHOD 2 : Component Video
If your television is equipped with Component Video inputs, connect a Component video cable (not supplied) 
from the  COMPONENT OUT  (P
R, PB and Y) jacks on the back of the product to the Component Video Input 
jacks on your TV. 
METHOD 3 : Composite Video
Connect the supplied Video cable from the  VIDEO OUT jack on the back of the product to the VIDEO IN jack 
on your TV.
NOTE
Resolutions available for the HDMI output are 480p(576p), 720p,1080i/1080p. See page 20 for the resolution 
setting. 
This product operates in Interlace scan mode 480i(576i) for component/composite output.
After making the video connection, set the Video input source on your TV to match the corresponding Video 
output mode on your product. 
Turn this product on fi rst before you set the video input source on your TV.  See your TV owner's manual for 
more information on how to select the TV's Video Input source.
CAUTION
Do not connect the unit through a VCR. Video signals fed through VCRs may be affected by copyright 
protection systems and the picture will be distorted on the television.
✎
`
`
`
!
`
SURROUNDSURROUND
SUBWOOFER CENTER FRONT
FRONT
SPEAKERS OUT
SPEAKER IMPEDANCE : 3
FM ANT
VIDEO OUTAUX IN
COMPONENT OUT
HDMI OUT
DIGITAL
AUDIO IN
ONLY
FOR SERVICE
FM ANT
AUX INDIGITALAUDIO IN
METHOD 3  (supplied)
RedBlue Green
METHOD 1(supplied) METHOD 2
 
						

							1 English
Connections
English 1
HDMI FUNCTION
HDMI Auto Detection Function
The product's video output will automatically change to HDMI mode when connecting an HDMI cable while power is on.
HDMI (High Defi nition Multimedia Interface)
HDMI is an interface that enables the digital transmission of video and audio data with just a single 
connector. Using HDMI, the product transmits a digital video and audio signal and displays a vivid picture 
on a TV having an HDMI input jack.
HDMI connection description
    - HDMI outputs only a pure digital signal to the TV.
    -  If your TV does not support HDCP (High-bandwidth Digital Content Protection), random noise appears 
on the screen.
What is the HDCP?
HDCP (High-band width Digital Content Protection) is a system for protecting DVD content outputted via 
HDMI from being copied. It provides a secure digital link between a video source (PC, DVD. etc) and a 
display device (TV, projector. etc). Content is encrypted at the source device to prevent unauthorized 
copies from being made.
Using Anynet+(HDMI-CEC)
Anynet+ is a function that enables you to control other Samsung Devices with your Samsung TV's remote 
control. Anynet + can be used by connecting this product to a SAMSUNG TV using a HDMI Cable. This is 
only available with SAMSUNG TV's that support Anynet+.
Connect the product to a Samsung TV with an HDMI cable. (See page 15)
Set the Anynet+ function on your TV. (See the TV instruction manual for more information.)
NOTE
The Anynet+ function supports some buttons of the remote control.
This function is not available if an HDMI cable does not support CEC.
Depending on your TV, certain HDMI output resolutions may not work.
Please refer to the user’s manual of your TV.
Please check the 
  logo (If your TV has an   logo, then it supports Anynet+ function.)
~
~
~
~
~
1.
2.
✎
`
`
`
`
 
						

							1 EnglishEnglish 1
02 Connections
Connecting the fm Antenna
Connect the FM antenna supplied to the FM Antenna jack.
Slowly move the antenna wire around until you fi nd a location where reception is good, then fasten it to a 
wall or other rigid surface.
NOTE
  This product does not receive AM broadcasts.
Connecting microphone
You can enjoy the feeling of a karaoke bar in the comfort of your home. 
Watch the video and sing along the lyrics displayed on the TV screen 
against the accompaniment.
Connect the microphone to the MIC jack on the front of the product.
Press the MIC VOL button to adjust the volume of the microphone.
Press the  ECHO button to adjust the echo level of the microphone.
   NOTE
If you hear strange noises (squealing or howling) while using the Karaoke feature, move the microphone away 
from the speakers. Turning down the microphone's volume or the speaker volume is also effective.
The microphone does not operate in the AUX and TUNER mode.
1.
2.
✎
`
1.
2.
3.
✎
`
`
SURROUNDSURROUND
SUBWOOFER CENTER FRONT
FRONT
SPEAKERS OUT
SPEAKER IMPEDANCE : 3
FM ANT
VIDEO OUTAUX IN
COMPONENT OUT
HDMI OUT
DIGITAL
AUDIO IN
ONLY
FOR SERVICEVIDEO OUTAUX IN
COMPONENT OUT
HDMI OUT
DIGITALAUDIO IN
FM Antenna (supplied)
5V 500mAMIC 1 MIC 2
 
						

							1 English
Connections
English 1
Connecting Audio from External Components
SURROUNDSURROUND
SUBWOOFER CENTER FRONT
FRONT
SPEAKERS OUT
SPEAKER IMPEDANCE : 3
FM ANT
VIDEO OUTAUX IN
COMPONENT OUT
HDMI OUT
DIGITAL
AUDIO IN
ONLY
FOR SERVICESURROUNDSURROUNDSUBWOOFER
CENTERFRONTFRONTSPEAKERS OUT
SPEAKER IMPEDANCE : 3
FM ANT
VIDEO OUTAUX IN
COMPONENT OUT
HDMI OUT
ONLYFOR SERVICE
Optical Cable
(not supplied)
Audio Cable (not supplied)
If the external Analog component 
has only one Audio Out, connect 
either left or right.
Set-Top Box VCR
AUX
OPTICAL
Red White
AUX : Connecting an External Analog Component
Analog signal components such as a VCR.
Connect  AUX IN (Audio) on the back of the product to the Audio Out of the external Analog component. 
Be sure to match the Colors of the connecting jacks.
Press the  FUNCTION  button to select  AUX input. 
The mode switches as follows : 
DVD/CD  ➞ D.IN  ➞ AUX  ➞ USB  ➞ FM
   NOTE
You can connect the Video Output jack of your VCR to the TV, and connect the Audio Output jacks of the 
VCR to this product.
OPTICAL : Connecting an External Digital Component
Digital signal components such as a Cable Box/Satellite receiver (Set-Top Box).
Connect the  DIGITAL AUDIO IN  (OPTICAL ) on the back of the product to the Digital Output of the 
external digital component.
Press the  FUNCTION  button to select  D.IN.
The mode switches as follows : 
DVD/CD  ➞ D.IN  ➞ AUX  ➞ USB  ➞ FM
1.
~
2. ~
✎
`
1.
2.~
 
						

							1 EnglishEnglish 1
03 Setup
Before Starting (Initial Setting)
Press the POWER button when it is plugged in 
TV for the fi rst time.
Initial Setting screen will be displayed.
Move   Select              Return
Initial settings I On-Screen Language
Select a language for the on-screen displays.
English
à´	¯
Nederlands FrançaisDeutsch Italiano
Press the ▲▼ buttons to select the desired 
language, then press the  ENTER button.
Press the  ENTER button to select Start button.
Press the ▲▼ buttons to select desired TV Aspect, 
then press the  ENTER button.
 
 NOTE
If you have not selected a preferred language in 
the initial settings, you will see a language 
selection window next time you turn on the 
product.
Your language selection will apply to all menus: 
On-Screen Menu, Disc Menu, Audio, Subtitle.
If you want to move to the previous screen, press the 
RETURN  button.
Once you select a menu language, you can change it by 
pressing the  STOP (@ ) button on the remote control for 
more than 5 seconds with no disc inserted.
When the Initial Setting screen does not appear, refer to 
the Initial Setting. (see  page 22)
1.
2.
3.
4.
✎
`
`
`
`
`
Setting the Setup menu
The access step may differ depending on the selected 
menu. The GUI (Graphical User Interface) in this 
manual may differ, depending on the fi rmware version.
1 2 3
4 5 6
7 8
0 9
FUNCTION
TV SOURCE
DSP / EQ
A B C DS/W LEVEL
REPEAT USB REC DIMMER TUNER 
MEMORY
MO/STDISC
MENUTITLE
INFO GIGA
VOL
TV CH V
TUNING V
DVD RECEIVER SELECT
SAMSUNG TV
MUTE
POWER
P L
TOOLS
1
2
3
4
1MENU BUTTON : Display the home menu.
2
ENTER / DIRECTION BUTTON
Move the cursor and select an item.
Select the currently selected item.
Confi rm the setting.
3RETURN BUTTON : Return to the previous 
setup menu.
4EXIT BUTTON : Exit the setup menu.
Function    DVD/CD       Settings
Press the 
POWER button.
Press the 
_+ buttons to select  Settings, then 
press the  ENTER button.
Press the 
$% buttons to select the desired 
menu, then press the  ENTER button.
Press the 
$% buttons to select the desired sub-
menu, then press the  ENTER button.
Press the 
$% buttons to select the desired 
item, then press the  ENTER button.
Press the  EXIT button to exit the setup menu.
1.
2.
3.
4.
5.
6.
Setup
 
						

							0 English
Setup
English 1
Display
You can configure various display options such as 
the TV Aspect, Resolution, etc.
TV Aspect
Depending on the type of television you have, you 
may want to adjust the screen setting.
4:3 Pan-Scan~
Select when you want to see the 16:9 
video supplied by the DVD without the 
black bars on top and bottom, even 
though you have a TV with a 4:3 ratio 
screen(extreme left and right portion of 
the movie picture will be cut off).
4:3 Letter Box~
Select when you want to see the total 
16:9 ratio screen DVD supplies, even 
though you have a TV with a 4:3 ratio 
screen. Black bars will appear at the 
top and bottom of the screen.
16:9 Wide~
You can view the full 16:9 picture on 
your widescreen TV.
NOTE
When using HDMI, the screen is automatically converted to the 
16:9 Wide mode and TV Aspect is deactivated.
If a DVD is in the 4:3 ratio, you cannot view it in the wide screen.
Since DVD discs are recorded in various image formats, they will 
look different depending on the software, the type of TV, and the 
TV aspect ratio setting.
BD Wise 
(Samsung products only)
BD Wise is Samsung's latest inter-connectivity 
feature. When you connect Samsung products with 
BD-Wise to each other via HDMI, the optimum 
resolution will be set automatically.
On  : The original resolution of the DVD disc will 
be output to the TV direct.
Off  : The output resolution will be fixed 
according to the Resolution previously set, 
regardless of the resolution of the disc. 
✎
`
`
`
~
~
NOTE
This will optimize the picture quality according 
to the content (In the DVD disc, etc) that you 
want to play and the product or your BD Wise-
compliant Samsung TV.
If you want to change the resolution in BD Wise 
mode, you must set BD mode to Off in advance.
BD Wise will be disabled if the product is connected 
to a device that does not support BD Wise.
Resolution 
Sets the output resolution of the HDMI video signal. The 
number in 576p, 720p, 1080i and 1080p indicates the 
number of lines of video. 
The i and p indicate interlace and progressive scan, 
respectively.
480p(576p)  : Outputs 480 lines of progressive video.
720p  : Outputs 720 lines of progressive video.
1080i  : Outputs 1080 lines of interlaced video.
1080p  : Outputs 1080 lines of progressive video.
BD Wise  : Automatically sets the optimal resolution when 
connected via HDMI to a TV with the BD Wise feature. (The 
BD Wise menu item appears only if BD Wise is set to On.)
NOTE
If component or composite is connected, the 
resolution supports only 480i(576i).
1080P may not appear depending on TV.
HDMI Format
You can optimize the Color setting from the HDMI 
output. Select a connected device Type.
Monitor :  Select if connected to a Monitor via HDMI.
TV :  Select if connected to a TV via HDMI.
Video Out Signal
Different countries apply different TV standard. 
You can select from NTSC or PAL.
NTSC :  You can select the NTSC video format
PAL :  You can select the PAL video format
Audio
Speaker Setting
Speaker Size
You can set the Speaker Size of the Center and Surround 
Speakers, as well as Test Tone in this mode.
✎
`
`
`
~
~
~
~
~
✎
`
`
~
~
~
~