Samsung HP-R4252 Plasma Television User Manual

							31
Connecting a Digital TV Set-Top Box
(480p, 720p, 1080i)
By inputting a high-bandwidth digital content protection High-Definition picture source
to the HDMI input jack on the TV, High-Definition pictures can be displayed on the
screen in their digital form.
Connecting to HDMI (High Definition Multimedia Interface)/DVI Compatible
TV
Connect the DVI AUDIO (L, R) input jacks on the TV with the AUDIO output jacks on the 
Set-Top Box using an audio cable.
Connect the HDMI input jack on the TV and the VIDEO output jack on the Set-Top Box 
using an HDMI/DVI cable.
How to Connect
1
2
Audio cable HDMI/DVI cable
From cable
or Antenna
Power cord
DTV Set-Top Box
BN68-00835A-00(002~035)  4/6/05  8:19 PM  Page 31 
						

							Connecting a Digital Audio System
There are many types of digital audio systems on the market today.
A simplified illustration of an audio system is shown below. For more information, see your
audio system owner’s manual.
32
If your audio system has a coaxial digital audio input, connect to the “COAXIAL” output jack 
on the TV.
If your audio system has a optical digital audio input, connect to the “OPTICAL“ output jack 
on the TV.
Be certain to remove the black cover from the optical output before inserting the cable.
If your system has both coaxial and optical digital audio inputs, SAMSUNG recommends 
you use the optical digital output on the TV.
Do not connect both optical and coaxial cables. This may damage your audio system.
• OPTICAL:  converts the electric signal into an optical light signal, and transmits it through 
glass fibers.
• COAXIAL: The digital audio signal is received through a coaxial copper cable.
How to Connect
1
2
3
TV
Digital Audio System
Optical cable Coaxial cablePower cord
BN68-00835A-00(002~035)  4/6/05  8:19 PM  Page 32 
						

							33
Connecting to an Analog Amplifier
TV
The “AUDIO OUT (AUDIO L/R)” terminals cannot be used for external speakers. 
You must hook them up to an amplifier.
When an audio amplifier is connected to the “AUDIO OUT (AUDIO L/R)” terminals: 
Decrease the gain (volume) of the audio amplifier, turn the TV’s internal mute on and adjust
the volume level with the volume control of the amplifier.
How to Connect
1
Analog AmplifierAudio cable
Power cord
BN68-00835A-00(002~035)  4/6/05  8:19 PM  Page 33 
						

							BN68-00835A-00(002~035)  4/6/05  8:19 PM  Page 34 
						

							PLASMA DISPLAY PANEL
Operation
Turning the TV On and Off ............................................................36
Viewing the Menus and Displays ..................................................40
Memorizing the Channels ............................................................41
Adding and Erasing Channels ......................................................44
Setting Up Your Remote Control ....................................................47
Viewing an External Signal Source ................................................49
BN68-00835A-00(002~035)  4/6/05  8:19 PM  Page 35 
						

							Turning the TV On and Off
36
Turning the TV On and Off
Press the POWER button on the remote control.
The TV will be turned on and you will be able to use its features.
You can also use the Power button on the front of the TV.
Note
•If your TV isn’t turned on when the POWER button is pressed:
Press the 
MODEbutton to check if the TV mode has been
chosen
. 
Plug & Play Feature
When the TV is initially powered On, basic customer settings proceed automatically and subsequently:
Setting the language, checking the antenna input, memorizing the channels, and setting the time.
Note
•The Plug & Play function operates after plugging in the TV for the first time.
1
Press the POWER button on the remote control.
The message “Menu language, Channels and Time 
will be set.” is displayed.
Press the ENTER button, then “Select the language of 
the OSD.” menu is automatically displayed.
2
Press the ENTER button to enter the language.
Press the ▲or ▼button to select language, then 
the ENTER button. “Select the antennas to 
memorize.” menu is automatically displayed.
Menu language, Channels 
and Time will be set.i
Start
Select the language of the OSD.
Menu Language          :English
Plug & Play
EnterSkip
English
Spanish
French
Move
BN68-00835A-00(036~049)  4/6/05  8:21 PM  Page 36 
						

							3
Press the ▲or ▼button to memorize the channels of
the selected connection. 
Press the ENTER button to select “Start”.
Notes
•  If the antenna is connected to ANT 1 IN (CABLE IN),
select “Cable” and if it is connected to ANT 2 IN 
(AIR IN), select “Air”.
•  If both ANT 1 IN and ANT 2 IN are connected, 
select the “Air + Cable”.
•
If the CableCARD is inserted into the “CableCARD” 
slot on the rear panel, “Cable” and “Air + Cable” 
are not available.
When selecting Cable TV :
Press the ▲or ▼button to select “Cable” or “Air + Cable”,
then press the ENTER button.
Press the ▲or ▼button to select “Digital Channel”, then 
press the ENTER button.
Press the ▲or ▼button to select “STD”, “HRC”, or “IRC”,
press the ENTER button.
Press the ▲or ▼button to select “Analog Channel”, then
press the ENTER button.
Press the ▲or ▼button to select “STD”, “HRC”, or “IRC”,
press the ENTER button.
Press the ▲or ▼button to select “Start”, then press the 
ENTER button to memorize the channels.
Note
•STD, HRC, and IRC identify various types of cable
TV systems. Contact your local cable company to
identify the type of cable system that exists in your
particular area. At this point the signal source has
been selected. Proceed to “Storing Channels in
Memory” on page 43.
37
Select the antennas to memorize.
Air               
Cable
Air + Cable
Plug & Play
EnterSkipMove
StartStart
Select the cable system.
Digital Channel : STD
√Analog Channel : STD√Start
Plug & Play
EnterSkipMove
Select the cable system.
Digital Channel : STD
√Analog Channel : STD√Start
Plug & Play
EnterSkipMove
Select the cable system.
Digital Channel :STD
√Analog Channel : STD√Start
Plug & Play
EnterSkipMove
STD
HRC
IRC
Select the cable system.
Digital Channel : STD
√Analog Channel :STD√Start
Plug & Play
EnterSkipMove
STD
HRC
IRC
Start
BN68-00835A-00(036~049)  4/6/05  8:21 PM  Page 37 
						

							38
4
The TV will begin memorizing all of the available
channels. After all the available channels are stored, 
the Auto program menu reappears. 
Press the ENTER button to select OK when channel 
memorization is complete.
“Set to daylight savings time.” menu is automatically 
displayed.
Press the ENTER button at any time to interrupt the 
memorization process.
5
Press the ENTER button. Press the ▲or ▼button to 
select “Yes” or “No”, then the ENTER button.
“Select the time zone in which you live” menu is 
automatically displayed.
6
Press the ▲or ▼button to highlight the time zone 
for your local area (and to move the highlight to the 
appropriate time zone on the map of the United States).
Press the ENTER button. 
If you have received a digital signal, the time will 
be set automatically. If not, see page 100 to set the 
clock.
7
The message “Completed. Time will be updated
automatically.” is displayed. 
When you have finished, press the ENTER button.
•The message will automatically disappear after a few 
seconds, even if the ENTER button is not pressed.
Plug & Play
EnterSkip
Auto Program in progress.
Cable  Channel  67
Stop
Plug & Play
EnterSkip
Auto Program is completed.
14 Channels were memorized.
Air : 9, Cable : 5.
OK
Set to daylight savings time.
Daylight Savings Time          :English
Plug & Play
EnterSkip
No
Ye s
Move
Select the time zone in which you live.
Plug & Play
Eastern
Central
Mountain
Pacific
Alaska
Hawaii
Enter
SkipMove
Completed. Time will 
be updated automatically.i
OK
BN68-00835A-00(036~049)  4/6/05  8:21 PM  Page 38 
						

							39
If you want to reset this feature...
1
Press the MENU button. Press the ▲or ▼button to select
“Setup”, then press the ENTER button.
2
Press the ENTER button to select “Plug & Play”.
3
For further details on setting up options, refer to the 
previous page.
Note
•Plug and Play can only be accessed in the TV mode.
Plug & Play√Language : English√Time√V-Chip√Caption√Menu Transparency : Medium√
†More
SetupTV
MoveEnterReturn
Menu language, Channels 
and Time will be set.i
Start
BN68-00835A-00(036~049)  4/6/05  8:21 PM  Page 39 
						

							40
Viewing the Menus and Displays
Your TV has a simple, easy-to-use menu system that appears on the TV screen. 
This system makes it convenient and fast to use features on the TV. 
Your TV also lets you display the status of many of your TV’s features.
Viewing the Menus
1
With the power on, press the MENU button on the
remote control. The main menu appears on the 
screen. The Input menu is selected.
2
Press the ▲or ▼button to move to items in the menu.
Press the œ/√/ENTER buttons to display, 
change, or use the selected items.
Press the ENTER button to enter items in the menu.
On screen menus disappear from the screen 
automatically after about two minutes or you can press 
the MENU or EXIT button on your remote control to exit 
the menu.
Displaying Status Information
Press the INFO button on the remote control.
The TV will display the Picture Mode, Sound Mode, MTS, 
V-Chip, and Current Time. 
Source List : TV√Edit Name√Anynet√
InputTV
MoveEnterReturn
Air 28
Picture Mode : Dynamic
Sound Mode : Custom
MTS : Stereo
V-Chip : Off
12 : 00 am Mono
BN68-00835A-00(036~049)  4/6/05  8:21 PM  Page 40