Samsung HP-R4252 Plasma Television User Manual

							PLASMA DISPLAY PANEL
Connections
Connecting VHF and UHF Antennas ..............................................22
Connecting Cable TV....................................................................23
Connecting CableCARD................................................................25
Connecting a VCR........................................................................26
Connecting a Camcorder ..............................................................27
Connecting a DVD Player..............................................................28
Connecting a DTV Receiver ..........................................................29
Connecting to HDMI (High Definition Multimedia Interface) ..............30
Connecting a Digital TV Set-Top Box ..............................................31
Connecting a Digital Audio System ................................................32
Connecting to an Analog Amplifier ................................................33
BN68-00835A-00(002~035)  4/6/05  8:19 PM  Page 21 
						

							Connecting VHF and UHF Antennas
22
Antennas with 75-ohm Round Leads
If your antenna looks like this: it has 75-ohm round leads.  
1
Plug the antenna lead into the ANT 2 IN (AIR IN) 
on the TV.
Use an antenna cable. (Sold Separately)
BN68-00835A-00(002~035)  4/15/05  7:14 PM  Page 22 
						

							23
Connecting Cable TV
You can connect different cable systems to your TV, including cable without a Cable box, and cable
with a Cable box that descrambles some or all channels.
Cable without a Cable Box
1
Plug the incoming cable into the ANT 1 IN (CABLE IN)
on the TV.
Use an antenna cable. (Sold Separately)
Cable with a Cable Box that Descrambles All Channels
1
Find the cable connected to the ANTENNA OUT 
terminal on your Cable box. This terminal might be 
labeled “ANT OUT”, “VHF OUT” or simply “OUT”.
2
Connect the cable to the ANT 1 IN (CABLE IN) on 
the TV. 
Use an antenna cable. (Sold Separately)
BN68-00835A-00(002~035)  4/15/05  7:14 PM  Page 23 
						

							24
Cable with a Cable Box that Descrambles Some (But Not All) Channels
To complete this connection you will need a two-way splitter, an RF (A/B) switch, and four coaxial
cables (which you can buy from your Samsung dealer or any electronics store).
1
Find and disconnect the cable that is 
connected to the ANTENNA IN terminal
of your Cable box. This terminal might 
be labeled “ANT IN”, “VHF IN” or  
simply, “IN”. Connect this cable to a 
two-way splitter.
2
Connect a coaxial cable between an
OUT terminal of the splitter and the 
IN terminal of the Cable box.
3
Connect a coaxial cable between the
ANTENNA OUT terminal of the Cable 
box and the B-IN terminal of the RF 
(A/B) switch.
4
Connect a coaxial cable between the
other OUT terminal of the Cable box 
and the A-IN terminal of the RF (A/B) 
switch.
5
Connect the last coaxial cable between
the OUT terminal of the RF (A/B) 
switch and the ANT 1 IN (CABLE IN) 
on the TV.
After youve made this connection, set the A/B switch to the “A” position for normal viewing. 
Set the A/B switch to the “B” position to view scrambled channels. (When you set the A/B switch to
“B”, you will need to tune your Set-Top Box to the Cable boxs output channel, which is usually
channel 3 or 4.)
BN68-00835A-00(002~035)  4/6/05  8:19 PM  Page 24 
						

							Connecting CableCARD
You must obtain a CableCARD from a local cable service provider.
Insert the CableCARD into the “CableCARD” slot and the message “CableCARD Inserted” 
is displayed on the screen. If the channel information does not exist, the message “Updating
Channel List” is displayed during channel information configuration. 
It could take several minutes to update the channel information depending on your cable
service provider.
The pairing information containing a telephone number, CableCARD ID, Host ID, and other
information will be displayed in about 2~3 minutes. If an error message is displayed, please
contact your service provider.
When the channel information configuration has finished, the message “Updating Completed”
is displayed, indicating that the channel list is now updated.
The Channel list can now be displayed by pressing CH LIST button.
Notes
•Once the channel list has been updated, only the channels on the channel list can be 
selected.
•Remove the CableCARD by carefully pulling it out with your hands since dropping the 
CableCARD may cause damage to it.
How to Connect
1
2
3
4
TV
Power cord
From cable TV
Please insert the card as shown.
25
BN68-00835A-00(002~035)  4/6/05  8:19 PM  Page 25 
						

							Connecting a VCR 
26
Connecting a VCR to the Video or S-Video/Audio jack
Connect the Video/Audio cables between the VIDEO or S-VIDEO/AUDIO input jacks on the 
TV and VIDEO or S-VIDEO/AUDIO output jacks on the VCR. 
(Note: For better video, use an S-Video cable.)
Note
•Please be sure to match the color coded input terminals and cable jacks.
Videotape Playback:
1. Turn on your TV.
2. Press the SOURCE button to select “AV” or “S-Video”.
3. Turn on your VCR, insert a videotape and press the Play button.
How to Connect
TV
S-Video cable Audio cable
Video cable VCR
Power cord
BN68-00835A-00(002~035)  4/6/05  8:19 PM  Page 26 
						

							Connecting a Camcorder
TV
S-Video cable Audio cable
Video cable Camcorder
Connect a Video/Audio cable between the VIDEO or S-VIDEO/AUDIO input jacks on the TV 
and the VIDEO or S-VIDEO/AUDIO output jacks on the camcorder. 
(Note: For better video, use an S-VIDEO cable.)
Note
•Please be sure to match the color coded input terminals and cable jacks.
Viewing Tapes
1. Turn on your TV.
2. Press the SOURCE button to select “AV” or “S-Video”.
3. Turn on your camcorder and set it to video mode. (For details, refer to your camcorder 
owner’s instructions.)
4. Insert the tape into the camcorder and press the Play button.
How to Connect
Viewing camcorder tapes
27
Power cord
BN68-00835A-00(002~035)  4/7/05  4:46 PM  Page 27 
						

							Connecting a DVD Player (480i, 480p)
28
Playing DVD
Connect the Y, PB, PR(COMPONENT1, 2) input jacks on the TV to the Y, PB, PRoutput jacks 
on the DVD player using a component cable. 
Connect the AUDIO L/R (COMPONENT1, 2) input jacks on the TV to the AUDIO output 
jacks on the DVD player using a audio cable.
Note 
•Please be sure to match the color coded input terminals and cable jacks.
To Play DVD:
1. Turn on your TV.
2. Press the SOURCE button to select “Component 1” or “Component 2”.
3. Turn on your DVD player, insert a DVD disc and press the Play button.
• For an explanation of component video, see your DVD player’s owner’s instructions.
How to Connect
1
2
TV
Audio cable Component cableDVD Player
Power cord
BN68-00835A-00(002~035)  4/6/05  8:19 PM  Page 28 
						

							Connecting a DTV Receiver (480p, 720p, 1080i)
This TV displays the optimum picture in 720p mode.
Watching DTV
Connect the cable or antenna to the antenna input jack on the DTV.
Connect the Y, P
B, PR(COMPONENT1, 2) or HDMI input jack on the TV to the Y, PB, PRor 
DVI output jacks on the DTV receiver using a component or HDMI/DVI cable.
Connect the AUDIO L/R (COMPONENT1, 2 or DVI AUDIO IN) input jacks on the TV with 
the AUDIO output jacks on the DTV receiver using an audio cable.
Note
•Please be sure to match the color coded input terminals and cable jacks.
To Watch DTV:
1. Turn on your TV.
2. Turn on your DTV receiver.
• For an explanation of component video, see your DTV receiver owner’s instructions.
3. Press the SOURCE button to select “Component1”, “Component2” or “HDMI”.
How to Connect
1
2
3
TV
DTV Receiver
29
HDMI/DVI cable Audio cable Component cable
Power cord
BN68-00835A-00(002~035)  4/6/05  8:19 PM  Page 29 
						

							Connecting to HDMI (High Definition 
Multimedia Interface) (480p, 720p, 1080i)
30
Watching DTV
Connect the cable or antenna to the antenna input jack on the DTV.
Connect the HDMI input jack on the TV with the HDMI output jack on the DTV Set-Top Box 
using an HDMI cable.
Note
•Please make sure the HDMI source’s power is on before selecting HDMI from the “Source List”
on the TV.
To Watch DTV:
1. Turn on your TV.
2. Turn on your DTV receiver.
• For an explanation of HDMI video, see your DTV receiver owner’s instructions.
3. Press the SOURCE button to select “HDMI”.
How to Connect
1
2
TV
DTV Set-Top Box HDMI cable
Power cord
BN68-00835A-00(002~035)  4/6/05  8:19 PM  Page 30